The firmware expects the port numbers for offloaded UDP tunnels in
Little Endian format. We accidentally sent the value in Big Endian
format which obviously will cause the wrong port number to be put into
the UDP tunnels list. This results in VxLAN and Geneve tunnel Rx
offloads being essentially disabled, unless the port number happens to
be identical after byte swapping. Note that i40e_aq_add_udp_tunnel()
will byteswap the parameter from host order into Little Endian so we
don't need worry about passing strictly a __le16 value to the command.

This patch essentially reverts b3f5c7bc ("i40e: Fix for extra byte
swap in tunnel setup", 2016-08-24), but in a way that makes the result
much more clear to the reader.

Fixes: b3f5c7bc ("i40e: Fix for extra byte swap in tunnel setup", 2016-08-24)
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Reviewed-by: NWilliams, Mitch A <mitch.a.williams@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.

As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Information reported to ethtool about link modes is wrong for 25G NIC.  Fix
it by checking for presence of 25G NIC, checking the link speed reported by
NIC firmware, and then assigning proper values to the
ethtool_link_ksettings struct.
Signed-off-by: NManish Awasthi <manish.awasthi@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The sunvnet netdev is connected to the controlling ldom's vswitch
for network bridging.  However, for higher performance between ldoms,
there also is a channel between each client ldom.  These connections are
represented in the sunvnet driver by a queue for each ldom.  The driver
uses select_queue to tell the stack which queue to use by tracking the mac
addresses on the other end of each port.  When a connected ldom shuts down,
the driver receives an LDC_EVENT_RESET and the port is removed from the
driver, thus a queue with no ldom on the other end will never be selected
for Tx.

The driver was trying to reinforce the "don't use this queue" notion with
netif_tx_stop_queue() and netif_tx_wake_queue(), which really should only
be used to signal a Tx queue is full (aka XOFF).  This misuse of queue
state resulted in NETDEV WATCHDOG messages and lots of unnecessary calls
into the driver's tx_timeout handler.  Simply removing these takes care
of the problem.

Orabug: 25190537
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make sure multicast packets get counted in the device.

Orabug: 25190537
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Track our used and unused queue indexies correctly.  Otherwise, as ports
dropped out and returned, they all eventually ended up with the same
queue index.

Orabug: 25190537
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In this driver, there is a "port" created for the connection to each of
the other ldoms; a netdev queue is mapped to each port, and they are
collected under a single netdev.  The generic netdev statistics show
us all the traffic in and out of our network device, but don't show
individual queue/port stats.  This patch breaks out the traffic counts
for the individual ports and gives us a little view into the state of
those connections.

Orabug: 25190537
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When an ldom VM is bound, the network vswitch infrastructure is set up for
it, but was being forced 'UP' by the userland switch configuration script.
When 'UP' but not actually connected to a running VM, the ipv6 neighbor
probes fail (not a horrible thing) and start cluttering up the kernel logs.
Funny thing: these are debug messages that never actually show up, but
we do see the net_ratelimited messages that say N callbacks were
suppressed.

This patch defers the netif_carrier_on() until an actual link has been
established with the VM, as indicated by receiving an LDC_EVENT_UP from
the underlying LDC protocol.  Similarly, we take the link down when we
see the LDC_EVENT_RESET.  Now when we see the ndo_open(), we reset the
link to get things talking again.

Orabug: 25525312
Signed-off-by: NShannon Nelson <shannon.nelson@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All IRQs owned by the PF and VF drivers share the same nondescript name
"octeon"; this makes it difficult to setup interrupt affinity.

Change the IRQ names to reflect their specific purpose:

    LiquidIO<id>-<func>-<type>-<queue pair num>

Examples:
    LiquidIO0-pf0-rxtx-3
    LiquidIO1-vf1-rxtx-0
    LiquidIO0-pf0-aux

We cannot use netdev->name for naming the IRQs because:

    1.  Early during init, the PF and VF drivers require interrupts to
        send/receive control data from the NIC firmware; so the PF and VF
        must request IRQs long before the netdev struct is registered.

    2.  The IRQ name can only be specified at the time it is requested.
        It cannot be changed after that.
Signed-off-by: NRick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NSatanand Burla <satananda.burla@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove invalid call to dma_sync_single_for_cpu() because previous DMA
allocation was coherent--not streaming.  Remove code that references fields
in struct list_head; replace it with calls to list_empty() and
list_first_entry().  Also, add comment to clarify complicated if statement.
Signed-off-by: NRick Farrington <ricardo.farrington@cavium.com>
Signed-off-by: NFelix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: NDerek Chickles <derek.chickles@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allows the BCMA version of the bgmac driver to obtain MAC address
from the device tree.  If no MAC address is specified there, then
the previous behavior (obtaining MAC address from SPROM) is
used.
Signed-off-by: NSteve Lin <steven.lin1@broadcom.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NJon Mason <jon.mason@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CONFIG_8xx is being deprecated. Since the includes dependent on
CONFIG_8xx are useless, just drop them.
Signed-off-by: NChristophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add basic support for handling suspend and resume.
Signed-off-by: NJane Li <jiel@marvell.com>
Reviewed-by: NJisheng Zhang <jszhang@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that port netdevs can be enslaved to a VRF master we need to make
sure the device's routing tables won't be flushed upon the insertion of
a l3mdev rule.

Note that we assume the notified l3mdev rule is a simple rule as used by
the VRF master. We don't check for the presence of other selectors such
as 'iif' and 'oif'.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a similar fashion to the previous patch, allow bridges and VLAN
devices on top of bridges to be enslaved to a VRF master device.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow port netdevs, LAG and VLAN devices stacked on top of these to be
enslaved to a VRF master device.

Upon enslavement, create a router interface (RIF) for the enslaved
netdev and associate it with a virtual router (VR) based on the VRF's
table ID.

If a RIF already exists for the netdev (f.e., due to the existence of an
IP address), then it's deleted and a new one is created with the
appropriate VR binding.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We usually destroy the netdev's router interface (RIF) when the last IP
address is removed from it.

However, we shouldn't do that if it's enslaved to an L3 master device.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a router interface (RIF) is created due to a netdev being enslaved
to a VRF master, then it should be associated with the appropriate
virtual router (VR) and not the default one.

If netdev is a VRF slave, lookup the VR based on the VRF's table ID.
Otherwise default to the MAIN table.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit c3852ef7 ("ipv4: fib: Replay events when registering FIB
notifier") we dumped the FIB tables and replayed the events to the
passed notification block.

However, we merely sent a RULE_ADD notification in case custom rules
were in use. As explained in previous patches, this approach won't work
anymore. Instead, we should notify the caller about all the FIB rules
and let it act accordingly.

Upon registration to the FIB notification chain, replay a RULE_ADD
notification for each programmed FIB rule, custom or not. The integrity
of the dump is ensured by the mechanism introduced in the above
mentioned commit.

Prevent regressions by making sure current listeners correctly sanitize
the notified rules.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Acked-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements workaround for errata 10GE_8 and ENET_11:
"HW reports length error for valid 64 byte frames with len <46 bytes"
by recovering them from error.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NQuan Nguyen <qnguyen@apm.com>
Signed-off-by: NToan Le <toanle@apm.com>
Tested-by: NFushen Chen <fchen@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch implements workaround for errata 10GE_1:
10Gb Ethernet port FIFO threshold default values are incorrect.
Signed-off-by: NQuan Nguyen <qnguyen@apm.com>
Signed-off-by: NToan Le <toanle@apm.com>
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Tested-by: NFushen Chen <fchen@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes Rx checksum validation logic and
adds NETIF_F_RXCSUM flag.
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the wrong logical OR operation by changing it to
bit-wise OR operation.

Fixes: 3bb502f8 ("drivers: net: xgene: fix statistics counters race condition")
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NQuan Nguyen <qnguyen@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the hardware checksum settings by properly program
the classifier. Otherwise, packet may be received with checksum error
on X-Gene1 SoC.
Signed-off-by: NQuan Nguyen <qnguyen@apm.com>
Signed-off-by: NIyappan Subramanian <isubramanian@apm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The configurable priority to traffic class mapping and the user specified
queue ranges are used to configure the traffic class, overriding the
hardware defaults when the 'hw' option is set to 0. However, when the 'hw'
option is non-zero, the hardware QOS defaults are used.

This patch makes it so that we can pass the data the user provided to
ndo_setup_tc. This allows us to pull in the queue configuration if the
user requested it as well as any additional hardware offload type
requested by using a value other than 1 for the hw value.

Finally it also provides a means for the device driver to return the level
supported for the offload type via the qopt->hw value. Previously we were
just always assuming the value to be 1, in the future values beyond just 1
may be supported.
Signed-off-by: NAmritha Nambiar <amritha.nambiar@intel.com>
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

At the end of the timeout loop, retries will always be zero so
the check for zero is redundant so remove it.  Also replace
printk with pr_err as recommended by checkpatch.
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares the main ISR for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch configures TSO for all available tx queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares the DMA initialization process for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares RX and TX set tail functions for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares tx and rx ring length configuration for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds rx watchdog configuration for all queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares DMA interrupts treatment for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares stmmac_err for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares the RX/TX DMA stop/start process for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares the DMA IRQ enable/disable process for multiple queues.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch prepares DMA Operation Mode configuration for multiple queues.
The work consisted on breaking the DMA operation Mode configuration function
into RX and TX scope and adapting its mechanism in stmmac_main.
Signed-off-by: NJoao Pinto <jpinto@synopsys.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A previous commit introduced a field that tracks the features
that are disabled due to HW resource limitations as opposed
to the featured disabled by the user. This patch changes the
name of the field to make it more readable since it might get
confusing when looking at code containing both the flags
field and the auto_disable_features field together.

Change-ID: Idcc9888659698f6fe3ccff17c8c3f09b5026f708
Signed-off-by: NHarshitha Ramamurthy <harshitha.ramamurthy@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: NBimmy Pujari <bimmy.pujari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>