This patch moves all definitions of the PCI resource names to an 'enum',
and also replaces some hard-coded resource variables with symbol
names. This change eases introduction of device specific resources.
Reviewed-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This cleanup removes unnecessary argument 'struct resource *res' in
pci_update_resource(), so it takes same arguments as other companion
functions (pci_assign_resource(), etc.).
Signed-off-by: NYu Zhao <yu.zhao@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

It's too large to be inlined.
Acked-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

This patch adds pci_swizzle_interrupt_pin(), which implements the
INTx swizzling algorithm specified in Table 9-1 of the "PCI-to-PCI
Bridge Architecture Specification," revision 1.2.

There are many architecture-specific implementations of this
swizzle that can be replaced by this common one.
Reviewed-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NBjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Device drivers that use pci_request_regions() (and similar APIs) have a
reasonable expectation that they are the only ones accessing their device.
As part of the e1000e hunt, we were afraid that some userland (X or some
bootsplash stuff) was mapping the MMIO region that the driver thought it
had exclusively via /dev/mem or via various sysfs resource mappings.

This patch adds the option for device drivers to cause their reserved
regions to the "banned from /dev/mem use" list, so now both kernel memory
and device-exclusive MMIO regions are banned.
NOTE: This is only active when CONFIG_STRICT_DEVMEM is set.

In addition to the config option, a kernel parameter iomem=relaxed is
provided for the cases where developers want to diagnose, in the field,
drivers issues from userspace.
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NArjan van de Ven <arjan@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The acpi_query_osc, __pci_osc_support_set, pci_osc_support_set, and
pcie_osc_support_set functions have been obsoleted in favor of setting
these capabilities during root bridge discovery with
pci_acpi_osc_support.  There are no longer any callers of these
functions, so remove them.
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The _OSC capability OSC_MSI_SUPPORT is set when the root bridge is added
with pci_acpi_osc_support(), so we no longer need to do it in the PCI
MSI driver.  Also adds the function pci_msi_enabled, which returns true
if pci=nomsi is not on the kernel command-line.
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The _OSC capabilities OSC_ACTIVE_STATE_PWR_SUPPORT and
OSC_CLOCK_PWR_CAPABILITY_SUPPORT are set when the root bridge is added
with pci_acpi_osc_support(), so we no longer need to do it in the ASPM
driver.  Also add the function pcie_aspm_enabled, which returns true if
pcie_aspm=off is not on the kernel command-line.
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The _OSC capability OSC_EXT_PCI_CONFIG_SUPPORT is set when the root
bridge is added with pci_acpi_osc_support() if we can access PCI
extended config space.

This adds the function pci_ext_cfg_avail which returns true if we can
access PCI extended config space (offset greater than 0xff). It
currently only returns false if arch=x86 and raw_pci_ext_ops is not set
(which might happen if pci=nommcfg is set on the kernel command-line).
Signed-off-by: NAndrew Patterson <andrew.patterson@hp.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Add pci_acpi_osc_support() and call it when a PCI bridge is added.  This
allows us to avoid having every individual PCI root bridge driver call
_OSC support for every root bridge in their probe functions, a
significant savings in boot time.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The pci-acpi.h file will not compile without including linux/acpi.h.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

PCI Advanced Features Capability is introduced by "Conventional PCI
Advanced Caps ECN" (can be downloaded in pcisig.com).  Add defines for
the various AF capabilities, including function level reset (FLR).
Reviewed-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NSheng Yang <sheng@linux.intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The __SWAB_64_THRU_32__ case of a 64-bit byte swap was depending on the
no-longer-existant ___swab32() method (three underscores).  We got rid
of some of the worst indirection and complexity, and now it should just
use the 32-bit swab function that was defined right above it.
Reported-and-tested-by: NNicolas Pitre <nico@cam.org>
Reported-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This implementation caused problems in userspace which can, and does
define _both_ __LITTLE_ENDIAN and __BIG_ENDIAN.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The first step to make swab.h a regular header that will
include an asm/swab.h with arch overrides.

Avoid the gratuitous differences introduced in the new
linux/swab.h by naming the ___constant_swabXX bits and
__fswabXX bits exactly as found in the old implementation
in byteorder/swab[b].h

Use this new swab.h in byteorder/[big|little]_endian.h and
remove the two old swab headers.

Although the inclusion of asm/byteorder.h looks strange in
linux/swab.h, this will allow each arch to move the actual
arch overrides for the swab bits in an asm file and then
the includes can be cleaned up without requiring a flag day
for all arches at once.

Keep providing __fswabXX in case some userspace was using them
directly, but the revised __swabXX should be used instead in
any new code and will always do constant folding not dependent
on the optimization level, which means the __constant versions
can be phased out in-kernel.

Arches that use the old-style arch macros will lose their
optimized versions until they move to the new style, but at
least they will still compile.  Many arches have already moved
and the patches to move the remaining arches are trivial.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

No one cares do_coredump()'s return value, and also it seems that it
is also not necessary. So make it void.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NWANG Cong <wangcong@zeuux.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove excess kernel-doc notation from rio header and driver:

Warning(include/linux/rio_drv.h:399): Excess function parameter or struct member 'buffer' description in 'rio_get_inb_message'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Provide a static debounce configuration mechanism for twl4030 GPIOs,
replacing the previous dynamic one.  The single user of that mechanism was
for MMC card detect debouncing.

Boards can provide a bitmask saying which GPIOs to debounce (30 msec).
It's always enabled for pins with the MMC card-detect/VMMCx link active,
so most boards won't need to set the debounce mask.

This is a net code shrink, including runtime footprint.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

- the type assigned at mount when no type is given is changed
  from 0 to AUTOFS_TYPE_INDIRECT. This was done because 0 and
  AUTOFS_TYPE_INDIRECT were being treated implicitly as the same
  type.

- previously, an offset mount had it's type set to
  AUTOFS_TYPE_DIRECT|AUTOFS_TYPE_OFFSET but the mount control
  re-implementation needs to be able distinguish all three types.
  So this was changed to make the type setting explicit.

- a type AUTOFS_TYPE_ANY was added for use by the re-implementation
  when checking if a given path is a mountpoint. It's not really a
  type as we use this to ask if a given path is a mountpoint in the
  autofs_dev_ioctl_ismountpoint() function.

- functions to set and test the autofs mount types have been added to
  improve readability and make the type usage explicit.

- the mount type is used from user space for the mount control
  re-implementtion so, for consistency, all the definitions have
  been moved to the user space include file include/linux/auto_fs4.h.
Signed-off-by: NIan Kent <raven@themaw.net>
Signed-off-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The parameter usage in the device node ioctl code uses arg1 and arg2 as
parameter names.  This patch redefines the parameter names to reflect what
they actually are in an effort to make the code more readable.
Signed-off-by: NIan Kent <raven@themaw.net>
Signed-off-by: NJeff Moyer <jmoyer@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Allows kprobes to probe __exit routine.  This adds flags member to struct
kprobe.  When module is freed(kprobes hooks module_notifier to get this
event), kprobes which probe the functions in that module are set to "Gone"
flag to the flags member.  These "Gone" probes are never be enabled.
Users can check the GONE flag through debugfs.

This also removes mod_refcounted, because we couldn't free a module if
kprobe incremented the refcount of that module.

[akpm@linux-foundation.org: document some locking]
[mhiramat@redhat.com: bugfix: pass aggr_kprobe to arch_remove_kprobe]
[mhiramat@redhat.com: bugfix: release old_p's insn_slot before error return]
Signed-off-by: NMasami Hiramatsu <mhiramat@redhat.com>
Acked-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: NMasami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add kprobe_insn_mutex for protecting kprobe_insn_pages hlist, and remove
kprobe_mutex from architecture dependent code.

This allows us to call arch_remove_kprobe() (and free_insn_slot) while
holding kprobe_mutex.
Signed-off-by: NMasami Hiramatsu <mhiramat@redhat.com>
Acked-by: NAnanth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This series of patches allows kprobes to probe module's __init and __exit
functions.  This means, you can probe driver initialization and
terminating.

Currently, kprobes can't probe __init function because these functions are
freed after module initialization.  And it also can't probe module __exit
functions because kprobe increments reference count of target module and
user can't unload it.  this means __exit functions never be called unless
removing probes from the module.

To solve both cases, this series of patches introduces GONE flag and sets
it when the target code is freed(for this purpose, kprobes hooks
MODULE_STATE_* events).  This also removes refcount incrementing for
allowing user to unload target module.  Users can check which probes are
GONE by debugfs interface.  For taking timing of freeing module's .init
text, these also include a patch which adds module's notifier of
MODULE_STATE_LIVE event.

This patch:

Add within_module_core() and within_module_init() for checking whether an
address is in the module .init.text section or .text section, and replace
within() local inline functions in kernel/module.c with them.

kprobes uses these functions to check where the kprobe is inserted.
Signed-off-by: NMasami Hiramatsu <mhiramat@redhat.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Acked-by: NRusty Russell <rusty@rustcorp.com.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Generalize the old at91rm9200 "bootstrap" bitbanging SPI master driver as
"spi_gpio", so it works with arbitrary GPIOs and can be configured through
platform_data.  Such SPI masters support:

 - any number of bus instances (bus_num is the platform_device.id)
 - any number of chipselects (one GPIO per spi_device)
 - all four SPI_MODE values, and SPI_CS_HIGH
 - i/o word sizes from 1 to 32 bits;
 - devices configured as with any other spi_master controller

When configured using platform_data, this provides relatively low clock
rates.  On platforms that support inlined GPIO calls, significantly
improved transfer speeds are also possible with a semi-custom driver.
(It's still painful when accessing flash memory, but less so.)

Sanity checked by using this version to replace both native controllers on
a board with six different SPI slaves, relying on three different
SPI_MODE_* values and both SPI_CS_HIGH settings for correct operation.

[akpm@linux-foundation.org: cleanups]
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Acked-by: NMagnus Damm <damm@igel.co.jp>
Tested-by: NMagnus Damm <damm@igel.co.jp>
Cc: Torgil Svensson <torgil.svensson@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

linux_binfmt uses list_head, so list.h is needed.

[akpm@linux-foundation.org: fix `make headerscheck']
Signed-off-by: NHiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

For NR_CPUS >= 16 values, FBC_BATCH is 2*NR_CPUS

Considering more and more distros are using high NR_CPUS values, it makes
sense to use a more sensible value for FBC_BATCH, and get rid of NR_CPUS.

A sensible value is 2*num_online_cpus(), with a minimum value of 32 (This
minimum value helps branch prediction in __percpu_counter_add())

We already have a hotcpu notifier, so we can adjust FBC_BATCH dynamically.

We rename FBC_BATCH to percpu_counter_batch since its not a constant
anymore.
Signed-off-by: NEric Dumazet <dada1@cosmosbay.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

f_op->poll is the only vfs operation which is not allowed to sleep.  It's
because poll and select implementation used task state to synchronize
against wake ups, which doesn't have to be the case anymore as wait/wake
interface can now use custom wake up functions.  The non-sleep restriction
can be a bit tricky because ->poll is not called from an atomic context
and the result of accidentally sleeping in ->poll only shows up as
temporary busy looping when the timing is right or rather wrong.

This patch converts poll/select to use custom wake up function and use
separate triggered variable to synchronize against wake up events.  The
only added overhead is an extra function call during wake up and
negligible.

This patch removes the one non-sleep exception from vfs locking rules and
is beneficial to userland filesystem implementations like FUSE, 9p or
peculiar fs like spufs as it's very difficult for those to implement
non-sleeping poll method.

While at it, make the following cosmetic changes to make poll.h and
select.c checkpatch friendly.

* s/type * symbol/type *symbol/		   : three places in poll.h
* remove blank line before EXPORT_SYMBOL() : two places in select.c

Oleg: spotted missing barrier in poll_schedule_timeout()
Davide: spotted missing write barrier in pollwake()
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: NMiklos Szeredi <mszeredi@suse.cz>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Brad Boyer <flar@allandria.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Roland McGrath <roland@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: Davide Libenzi <davidel@xmailserver.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Create a helper macro to divide two numbers and round the result to the
nearest whole number.  This is a helper macro for hwmon drivers that want
to convert incoming sysfs values per standard hwmon practice, though the
macro itself can be used by anyone.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com>
Cc: Gabor Gombas <gombasg@sztaki.hu>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Ingo Molnar <mingo@elte.hu>,
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The atomic_t type cannot currently be used in some header files because it
would create an include loop with asm/atomic.h.  Move the type definition
to linux/types.h to break the loop.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

xacct_add_tsk() relies on do_exit()->update_hiwater_xxx() and uses
mm->hiwater_xxx directly, this leads to 2 problems:

- taskstats_user_cmd() can call fill_pid()->xacct_add_tsk() at any
  moment before the task exits, so we should check the current values of
  rss/vm anyway.

- do_exit()->update_hiwater_xxx() calls are racy.  An exiting thread can
  be preempted right before mm->hiwater_xxx = new_val, and another thread
  can use A_LOT of memory and exit in between.  When the first thread
  resumes it can be the last thread in the thread group, in that case we
  report the wrong hiwater_xxx values which do not take A_LOT into
  account.

Introduce get_mm_hiwater_rss() and get_mm_hiwater_vm() helpers and change
xacct_add_tsk() to use them.  The first helper will also be used by
rusage->ru_maxrss accounting.

Kill do_exit()->update_hiwater_xxx() calls.  Unless we are going to
decrease rss/vm there is no point to update mm->hiwater_xxx, and nobody
can look at this mm_struct when exit_mmap() actually unmaps the memory.
Signed-off-by: NOleg Nesterov <oleg@redhat.com>
Acked-by: NHugh Dickins <hugh@veritas.com>
Reviewed-by: NKOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Acked-by: NBalbir Singh <balbir@linux.vnet.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

s_syncing livelock avoidance was breaking data integrity guarantee of
sys_sync, by allowing sys_sync to skip writing or waiting for superblocks
if there is a concurrent sys_sync happening.

This livelock avoidance is much less important now that we don't have the
get_super_to_sync() call after every sb that we sync.  This was replaced
by __put_super_and_need_restart.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove WB_SYNC_HOLD.  The primary motiviation is the design of my
anti-starvation code for fsync.  It requires taking an inode lock over the
sync operation, so we could run into lock ordering problems with multiple
inodes.  It is possible to take a single global lock to solve the ordering
problem, but then that would prevent a future nice implementation of "sync
multiple inodes" based on lock order via inode address.

Seems like a backward step to remove this, but actually it is busted
anyway: we can't use the inode lists for data integrity wait: an inode can
be taken off the dirty lists but still be under writeback.  In order to
satisfy data integrity semantics, we should wait for it to finish
writeback, but if we only search the dirty lists, we'll miss it.

It would be possible to have a "writeback" list, for sys_sync, I suppose.
But why complicate things by prematurely optimise?  For unmounting, we
could avoid the "livelock avoidance" code, which would be easier, but
again premature IMO.

Fixing the existing data integrity problem will come next.
Signed-off-by: NNick Piggin <npiggin@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove page_remove_rmap()'s vma arg, which was only for the Eeek message.
And remove the BUG_ON(page_mapcount(page) == 0) from CONFIG_DEBUG_VM's
page_dup_rmap(): we're trying to be more resilient about that than BUGs.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Complete zap_pte_range()'s coverage of bad pagetable entries by calling
print_bad_pte() on a pte_file in a linear vma and on a bad swap entry.
That needs free_swap_and_cache() to tell it, which will also have shown
one of those "swap_free" errors (but with much less information).

Similar checks in fork's copy_one_pte()?  No, that would be more noisy
than helpful: we'll see them when parent and child exec or exit.

Where do_nonlinear_fault() calls print_bad_pte(): omit !VM_CAN_NONLINEAR
case, that could only be a bug in sys_remap_file_pages(), not a bad pte.
VM_FAULT_OOM rather than VM_FAULT_SIGBUS?  Well, okay, that is consistent
with what happens if do_swap_page() operates a bad swap entry; but don't
we have patches to be more careful about killing when VM_FAULT_OOM?
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Simplify the PAGE_FLAGS checking and clearing when freeing and allocating
a page: check the same flags as before when freeing, clear ALL the flags
(unless PageReserved) when freeing, check ALL flags off when allocating.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Swap allocation has always started from the beginning of the swap area;
but if we're dealing with a solidstate swap device which can only remap
blocks within limited zones, that would sooner wear out the first zone.

Therefore sys_swapon() test whether blk_queue is non-rotational, and if so
randomize the cluster_next starting position for allocation.

If blk_queue is nonrot, note SWP_SOLIDSTATE for later use, and report it
with an "SS" at the right end of the kernel's "Adding ...  swap" message
(so that if it's both nonrot and discardable, "SSD" will be shown there).
Perhaps something should be shown in /proc/swaps (swapon -s), but we have
to be more cautious before making any addition to that format.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Joern Engel <joern@logfs.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When scan_swap_map() finds a free cluster of swap pages to allocate,
discard the old contents of the cluster if the device supports discard.
But don't bother when swap is so fragmented that we allocate single pages.

Be careful about racing allocations made while we're scanning for a
cluster; and hold up allocations made while we're discarding.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Joern Engel <joern@logfs.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

When adding swap, all the old data on swap can be forgotten: sys_swapon()
discard all but the header page of the swap partition (or every extent but
the header of the swap file), to give a solidstate swap device the
opportunity to optimize its wear-levelling.

If that succeeds, note SWP_DISCARDABLE for later use, and report it with a
"D" at the right end of the kernel's "Adding ...  swap" message.  Perhaps
something should be shown in /proc/swaps (swapon -s), but we have to be
more cautious before making any addition to that format.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Nick Piggin <nickpiggin@yahoo.com.au>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Matthew Wilcox <matthew@wil.cx>
Cc: Joern Engel <joern@logfs.org>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: Donjun Shin <djshin90@gmail.com>
Cc: Tejun Heo <teheo@suse.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>