Signed-off-by: NMike Turquette <mturquette@linaro.org>

Some devices require their clocks to be available with a specific
dev-id con-id mapping. With DT, the clocks can be found by default
only with their name, or alternatively through the device node of
the consumer. With drivers, that don't support DT fully yet, add
mechanism to register specific clock names.
Signed-off-by: NTero Kristo <t-kristo@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add a clock type that associates a regmap pointer and some
enable/disable bits with a clk_hw struct. This will be the struct
that a hw specific implementation wraps if it wants to use the
regmap helper functions.
Signed-off-by: NStephen Boyd <sboyd@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

sirfprima2 and sirfatlas6 are two different SoCs in CSR SiRF series. for
prima2 and atlas6, there are many shared clocks but there are still
some different register layout and hardware clocks, then result in
different clock table.

here we re-arch the driver to
1. clk-common.c provides common clocks for prima2 and atlas6,
2. clk-prima2.h describles registers of prima2 and clk-prima2.c provides
prima2 specific clocks and clock table.
3. clk-atlas6.h describles registers of atlas6 and clk-atlas6.c provides
atlas6 specific clocks and clock table.
4. clk.h and clk.c expose external interfaces and provide uniform entry
for both prima2 and atlas6.

so both prima2 and atlas6 will get support by drivers/clk/sirf.
Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Signed-off-by: NRongjun Ying <Rongjun.Ying@csr.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add a driver for SILabs 570, 571, 598, 599 programmable oscillators.
The devices generate low-jitter clock signals and are reprogrammable via
an I2C interface.
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

The R-Car Gen2 SoCs (R8A7790 and R8A7791) have several clocks that are
too custom to be supported in a generic driver. Those clocks can be
divided in two categories:

- Fixed rate clocks with multiplier and divisor set according to boot
  mode configuration

- Custom divider clocks with SoC-specific divider values

This driver supports both.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NKumar Gala <galak@codeaurora.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Enable common clock driver of Hi3620 SoC. clkgate-seperated driver is
used to support the clock gate that enable/disable/status registers
are seperated.
Signed-off-by: NHaojian Zhuang <haojian.zhuang@gmail.com>

This patch adds support for the clocks provided by the Clock Management
Unit of Energy Micro's efm32 Giant Gecko SoCs including device tree
bindings.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Now build the keystone common clock drivers. The build is made
conditional based on COMMON_CLK_KEYSTONE
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

clk: Add APM X-Gene SoC clock driver for reference, PLL, and device clocks.
Signed-off-by: NLoc Ho <lho@apm.com>
Signed-off-by: NKumar Sankaran <ksankaran@apm.com>
Signed-off-by: NVinayak Kale <vkale@apm.com>
Signed-off-by: NFeng Kan <fkan@apm.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This patch adds support to register three(AP/CP/BT) buffered 32.768 KHz
outputs of mfd-s2mps11 with common clock framework.
Signed-off-by: NYadwinder Singh Brar <yadi.brar@samsung.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This adds basic support for gate-clocks on Rockchip SoCs.
There are 16 gates in each register and use the HIWORD_MASK
mechanism for changing gate settings.

The gate registers form a continuos block which makes the dt node
structure a matter of taste, as either all 160 gates can be put into
one gate clock spanning all registers or they can be divided into
the 10 individual gates containing 16 clocks each.
The code supports both approaches.
Signed-off-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

I got a build error today that made me realize that it is not
possible to build a kernel for a SiRF platform without enabling
CONFIG_PRIMA2, since a lot of common code depends on CONFIG_PRIMA2.

This fixes all occurences that appear like common SiRF code.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NWolfram Sang <wsa@the-dreams.de>
Acked-by: NMark Brown <broonie@linaro.org>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: NBarry Song <Baohua.Song@csr.com>
Acked-by: NMike Turquette <mturquette@linaro.org>

This patch adds a basic clock driver for the TI-Nspire calculator
series.

Changes from v1:
* Removed filename in header comment
* Removed unnecessary #undef EXTRACT statement
Signed-off-by: NDaniel Tang <dt.tangr@gmail.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>
[mturquette@linaro.org: fixed $SUBJECT and changelog max width]

This adds the clock driver for Freescale PowerPC corenet
series SoCs using common clock infrastructure.
Signed-off-by: NTang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: NLi Yang <leoli@freescale.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Migrate the Zynq platform and its drivers to use the new clock
controller driver.
Signed-off-by: NSoren Brinkmann <soren.brinkmann@xilinx.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-serial@vger.kernel.org
Signed-off-by: NMichal Simek <michal.simek@xilinx.com>
Acked-by: NMike Turquette <mturquette@linaro.org>

This patch adds a common clock driver for Silicon Labs Si5351a/b/c
i2c programmable clock generators. Currently, the driver does not
support VXCO feature of si5351b. Passing platform_data or DT bindings
selectively allows to overwrite stored Si5351 configuration which is
very helpful for clock generators with empty eeprom configuration.
Corresponding device tree binding documentation is also added.
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Tested-by: NDaniel Mack <zonque@gmail.com>
Acked-by: NGuenter Roeck <linux@roeck-us.net>
Tested-by: NMichal Bachraty <michal.bachraty@streamunlimited.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This commit implements the base CPU clocks for sunxi devices. It has
been tested using a slightly modified cpufreq driver from the
linux-sunxi 3.0 tree.

Additionally, document the new bindings introduced by this patch.

Idling:
    / # cat /sys/kernel/debug/clk/clk_summary
       clock                        enable_cnt  prepare_cnt  rate
    ---------------------------------------------------------------------
     osc32k                         0           0            32768
     osc24M_fixed                   0           0            24000000
        osc24M                      0           0            24000000
           apb1_mux                 0           0            24000000
              apb1                  0           0            24000000
           pll1                     0           0            60000000
              cpu                   0           0            60000000
                 axi                0           0            60000000
                    ahb             0           0            60000000
                       apb0         0           0            30000000
     dummy                          0           0            0

After "yes >/dev/null &":
    / # cat /sys/kernel/debug/clk/clk_summary
       clock                        enable_cnt  prepare_cnt  rate
    ---------------------------------------------------------------------
     osc32k                         0           0            32768
     osc24M_fixed                   0           0            24000000
        osc24M                      0           0            24000000
           apb1_mux                 0           0            24000000
              apb1                  0           0            24000000
           pll1                     0           0            1008000000
              cpu                   0           0            1008000000
                 axi                0           0            336000000
                    ahb             0           0            168000000
                       apb0         0           0            84000000
     dummy                          0           0            0
Signed-off-by: NEmilio López <emilio@elopez.com.ar>
Acked-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Not all clocks are required to be decomposed into basic clock
types but at the same time want to use the functionality
provided by these basic clock types instead of duplicating.

For example, Tegra SoC has ~100 clocks which can be decomposed
into Mux -> Div -> Gate clock types making the clock count to
~300. Also, parent change operation can not be performed on gate
clock which forces to use mux clock in driver if want to change
the parent.

Instead aggregate the basic clock types functionality into one
clock and just use this clock for all operations. This clock
type re-uses the functionality of basic clock types and not
limited to basic clock types but any hardware-specific
implementation.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

All Samsung platforms include different types of clock including
fixed-rate, mux, divider and gate clock types. There are typically
hundreds of such clocks on each of the Samsung platforms. To enable
Samsung platforms to register these clocks using the common clock
framework, a bunch of utility functions are introduced here which
simplify the clock registration process. The clocks are usually
statically instantiated and registered with common clock framework.
Reviewed-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Tested-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Reviewed-by: NTomasz Figa <t.figa@samsung.com>
Tested-by: NTomasz Figa <t.figa@samsung.com>
Tested-by: NHeiko Stuebner <heiko@sntech.de>
Signed-off-by: NThomas Abraham <thomas.abraham@linaro.org>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NKukjin Kim <kgene.kim@samsung.com>

This driver adds support for the AXI clkgen pcore to the common clock framework.
The AXI clkgen pcore is a AXI front-end to the MMCM_ADV frequency synthesizer
commonly found in Xilinx FPGAs.

The AXI clkgen pcore is used in Analog Devices' reference designs targeting
Xilinx FPGAs.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Patch 85a18198 "clk: sunxi: Use common of_clk_init() function"
removed the clk-sunxi.c file but left the Makefile entry, which
causes a build error in multi_v7_defconfig:

make[4]: *** No rule to make target `drivers/clk/clk-sunxi.o', needed by `drivers/clk/built-in.o'.

The obvious fix is to remove the extraneous line from the
Makefile.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Maxime Ripard <maxime.ripard@anandra.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Add Tegra specific clocks, pll, pll_out, peripheral, frac_divider, super.
Signed-off-by: NPrashant Gaikwad <pgaikwad@nvidia.com>
[swarren: alloc sizeof(*foo) not sizeof(struct foo), add comments re:
storing pointers to stack variables, make a timeout loop more idiomatic,
use _clk_pll_disable() not clk_disable_pll() from _program_pll() to
avoid redundant lock operations, unified tegra_clk_periph() and
tegra_clk_periph_nodiv(), unified tegra_clk_pll{,e}, rename all clock
registration functions so they don't have the same name as the clock
structs, return -EINVAL from clk_plle_enable when matching table rate
not found, pass ops to _tegra_clk_register_pll rather than a bool.]
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NStephen Warren <swarren@nvidia.com>

Intel Lynxpoint Low Power Subsystem hosts peripherals like UART, I2C and
SPI controllers. For most of these there is a configuration register that
allows software to enable and disable the functional clock. Disabling the
clock while the peripheral is not used saves power.

In order to take advantage of this we add a new clock gate of type
lpss_gate that just re-uses the ordinary clk_gate but in addition is able
to enumerate the base address register of the device using ACPI.

We then create a clock tree that models the Lynxpoint LPSS clocks using
these gates and fixed clocks so that we can pass clock rate to the drivers
as well.
Signed-off-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NMike Turquette <mturquette@linaro.org>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

The list of common clock types was getting a bit unmanageable.  This
patch puts only one file on each line and reorders the object files
alphabetically.  Also a newline is added to separate the sections.
Reported-by: NStephen Boyd <sboyd@codeaurora.org>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This driver allows to provide DT clocks for core clocks found on
Marvell Kirkwood, Dove & 370/XP SoCs. The core clock frequencies and
ratios are determined by decoding the Sample-At-Reset registers.

Although technically correct, using a divider of 0 will lead to
div_by_zero panic. Let's use a ratio of 0/1 instead to fail later
with a zero clock.
Signed-off-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: NSebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Tested-by Gregory CLEMENT <gregory.clement@free-electrons.com>

Signed-off-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Cc: Mike Turquette <mturquette@ti.com>

Make the Zynq platform use the newly created zynq clk bindings.
Signed-off-by: NJosh Cartwright <josh.cartwright@ni.com>
Acked-by: NMichal Simek <michal.simek@xilinx.com>

On OMAP4+ platforms the functional clock for the McPDM IP is suplied by
the twl6040 codec (bit clock on the PDM bus).
This common clock driver for twl6040 will register the mcpdm_fclk clock to
be used by the McPDM driver to make sure that the needed clocks are
available when needed.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This patch adds common clock framework support for arch-vt8500.
Support for PLL and device clocks on VT8500, WM8505 and WM8650
are included.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>
Acked-by: NMike Turquette <mturquette@linaro.org>

This patch adds a minimal stub clock driver for the BCM2835. Its sole
purpose is to allow the PL011 AMBA clk_get() API calls to provide
something that looks enough like a clock that the driver probes and
operates correctly.

This patch was extracted from git://github.com/lp0/linux.git branch
rpi-split as of 2012/09/08, and modified as follows:

* Reworked to call clk_register_fixed_rate(), and clk_register_clkdev()
  rather than using static data to represent the clocks.
* Moved implementation to drivers/clk/.
* Modified .dev_id for UART clocks to match UART DT node names.
* s/bcm2708/bcm2835/.
* Modified device tree vendor prefix.
Signed-off-by: NChris Boot <bootc@bootc.net>
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NDom Cobley <popcornmix@gmail.com>
Signed-off-by: NDom Cobley <dc4@broadcom.com>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Acked-by: NMike Turquette <mturquette@linaro.org>

The managed clk functions are currently only available when the generic clk
lookup framework is build. But the managed clk functions are merely wrappers
around clk_get and clk_put and do not depend on any specifics of the generic
lookup functions and there are still quite a few custom implementations of the
clk API. So make the managed functions available whenever the clk API is
implemented.

The patch also removes the custom implementation of devm_clk_get for the
coldfire platform.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This patch supports max77686 mfd's clock driver using common clock frame work.
max77686 has 3 clock ouputs which all are generated from crystal oscillator and
SOC can enable/disable them via I2C bus. All clocks are fixed-rate clock sources
so that it doesn't supply interface for changing clock rate.
Driver uses regmap API to communicate with internal register.
Signed-off-by: NJonghwa Lee <jonghwa3.lee@samsung.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Remove machine specific clock implementation and switch to use
new common clock framework.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This adds clock support to Loongson1B SoC using the common clock
infrastructure.
Signed-off-by: NKelvin Cheung <keguang.zhang@gmail.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

add mmp specific clocks including apbc cloks, apmu clocks,
and pll2, fraction clocks
Signed-off-by: NChao Xie <xiechao.mail@gmail.com>
Reviewed-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

This converts the ARM RealView machine over to using the common
clock. The approach is similar to the one used for the Integrator,
and we're reusing the ICST wrapper code.

We have to put the clock intialization in the timer init function
for the clocks to be available when initializing the timer,
keeping them in early_init() is too early for the common clk.

Since we now have to go down and compile drivers/clk/versatile
a CONFIG_COMMON_CLK_VERSATILE symbol has been added so the proper
code gets compiled into the kernel for either machine. A leftover
CLK_VERSATILE in the Integrator Kconfig was fixed up to use
the new symbol as well.

Tested on ARM RealView PB1176.

Cc: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Signed-off-by: NBarry Song <Baohua.Song@csr.com>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NMike Turquette <mturquette@linaro.org>

Adding core definitions for Altera's SOCFPGA ARM platform.
Mininum support for Altera's SOCFPGA Cyclone 5 hardware.
Signed-off-by: NDinh Nguyen <dinguyen@altera.com>
Reviewed-by: NPavel Machek <pavel@denx.de>
Reviewed-by: NRob Herring <rob.herring@calxeda.com>
Reviewed-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NArnd Bergmann <arnd@arndb.de>

This adds real clock support to Calxeda Highbank SOC using the common
clock infrastructure.
Signed-off-by: NRob Herring <rob.herring@calxeda.com>
[mturquette@linaro.org: fixed up invalid writes to const struct member]
Signed-off-by: NMike Turquette <mturquette@linaro.org>