mmc_send_ext_csd() is an exported function used by both the mmc core
and the mmc block layer. Let's remove the local duplicated definition
in the mmc core.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

Some eMMC and SD cards implement a DSR register that allows to tune
raise/fall times and drive strength of the CMD and DATA outputs.
The values to use depend on the card in use and the host.
It might be needed to reduce the drive strength to prevent voltage peaks
above the host's specification.

Implement a 'dsr' devicetree property that allows to specify the value
to set the DSR to. For non-dt setups the new members of mmc_host can be
set by board code.

This patch was initially authored by Sascha Hauer. It contains
improvements authored by Markus Niebel and Uwe Kleine-König.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMarkus Niebel <Markus.Niebel@tq-group.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

The mmc_card_sleep|awake APIs are not being used since the support is
already properly encapsulated within the suspend sequence. Sleep|awake
command is also specific for eMMC.

We remove the sleep|awake bus_ops, the mmc_card_sleep|awake APIs and
move the code into the mmc specific core instead. This also includes
the mmc ops function, mmc_sleepawake. All releated functions have then
become static and we have got far less code to maintain.

Additionally this patch also simplifies the code from mmc_sleepawake,
since it is only used to put the card to sleep and not awake.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

HPI command is defined in eMMC4.41.
This feature is important for eMMC4.5 devices.
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

CMD6 is an R1B-type command, where DAT is used as busy. Depending
on register written using CMD6, timeout value can be different
as per spec.
Signed-off-by: NAndrei Warkentin <andreiw@motorola.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some old MMC devices fail with the 4/8 bits the driver tries to use
exclusively.  This patch adds a test for the given bus setup and falls
back to the lower bit mode (until 1-bit mode) when the test fails.

[Major rework and refactoring by tiwai]
[Quirk addition and many fixes by prakity]
Signed-off-by: NAries Lee <arieslee@jmicron.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Tested-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add support for the new MMC command SLEEP_AWAKE.
Signed-off-by: NJarkko Lavinen <jarkko.lavinen@nokia.com>
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Acked-by: NMatt Fleming <matt@console-pimps.org>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: "Roberto A. Foglietta" <roberto.foglietta@gmail.com>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Denis Karpov <ext-denis.2.karpov@nokia.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Philip Langdale <philipl@overt.org>
Cc: "Madhusudhan" <madhu.cr@ti.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Teach the MMC/SD/SDIO core about using SPI mode.

 - Use mmc_host_is_spi() so enumeration works through SPI signaling
   and protocols, not just the native versions.

 - Provide the SPI response type flags with each request issued,
   including requests from the new lock/unlock code.

 - Understand that cmd->resp[0] and mmc_get_status() results for SPI
   return different values than for "native" MMC/SD protocol; this
   affects resetting, checking card lock status, and some others.

 - Understand that some commands act a bit differently ... notably:
     * OP_COND command doesn't return the OCR
     * APP_CMD status doesn't have an R1_APP_CMD analogue

Those changes required some new and updated primitives:

 - Provide utilities to access two SPI-only requests, and one
   request that wasn't previously needed:
     * mmc_spi_read_ocr() ... SPI only
     * mmc_spi_set_crc() ... SPI only (override by module parm)
     * mmc_send_cid() ... for use without broadcast mode

 - Updated internal routines:
     * Previous mmc_send_csd() modified into mmc_send_cxd_native();
       it uses native "R2" responses, which include 16 bytes of data.
     * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
       helper for command-and-data access
     * Bugfix to that mmc_send_cxd_data() code:  dma-to-stack is
       unsafe/nonportable, so kmalloc a bounce buffer instead.

 - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper

 - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
   those helper routines based on whether they're native or SPI

The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI:  MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Make sure all headers in the files reflect their true position
in the tree.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>

Move protocol operations and definitions into their own files
in an effort to separate protocol handling and bus
arbitration more clearly.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>