Use the fence of the new frontbuffer, if any.

Generating a new fence could cause us to wait for completely unrelated
rendering to finish before performing the flip.
Signed-off-by: NMichel Dänzer <michel.daenzer@amd.com>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Alan Cox reported a missing check on the kmalloc return value for the
allocation of a temporary mode used for searching for the LVDS downlock
frequency. This allocation is roughly 200 bytes, a little too large to
friviously place on the stack. However, we can simply use the few bytes
we need stored within the original DVO timing data, skip the translation
and do the compare directly between the timing data rather than on a
mode, thus avoiding the need for any temporary allocations.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>

The read back of the available FIFO entries is vital for system
stability, but extremely costly. However, we only need a guide so as to
avoid eating into the reserved entries and since we are the only
consumer we can cache the read of the count from the last write.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

opregion-based platforms will send ACPI video event 0x80 for a range of
notification types for legacy compatibility. This is interpreted as a
display switch event, which may not be appropriate in the circumstances.
When we receive such an event we should make sure that the platform is
genuinely requesting a display switch before passing that event through
to userspace.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Tested-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Do not use this bit to indicate that load detection has completed,
instead just wait for vblank, at which point the load registers will
have been updated.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Tested-by: NYi Sun <yi.sun@intel.com>

Signed-off-by: NKeith Packard <keithp@keithp.com>
Tested-by: NYi Sun <yi.sun@intel.com>

drm_pci_device_is_pcie duplicates the funcationality of pci_is_pcie.
Convert callers of the former to the latter.  This has the side benefit
of removing an unnecessary search in the PCI configuration space due to
using a saved PCIe capability offset.

[airlied: update for new callsite]
Signed-off-by: NJon Mason <jdmason@kudzu.us>
Signed-off-by: NDave Airlie <airlied@redhat.com>

...which is measured by the size and not the amount of space remaining.

Waiting upon size-8, did one of two things. In the common case with more
than 8 bytes available to write into the ring, it would return
immediately. Otherwise, it would timeout given the impossible condition
of waiting for more space than is available in the ring, leading to
warnings such as:

[drm:intel_cleanup_ring_buffer] *ERROR* failed to quiesce render ring
whilst cleaning up: -16
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NKeith Packard <keithp@keithp.com>

This reverts commit a51f7a66.

We still have a few Ironlake and Sandybridge machines which fail when
RC6 is enabled. Better luck next release?
Signed-off-by: NKeith Packard <keithp@keithp.com>

i915_driver_load adds a write-combining MTRR region for the GTT
aperture to improve memory speeds through the aperture. If
i915_driver_load fails after this, it would not have cleaned up the
MTRR. This shouldn't cause any problems, except for consuming an MTRR
register. Still, it's best to clean up completely in the failure path,
which is easily done by calling mtrr_del if the mtrr was successfully
allocated.

i915_driver_load calls i915_gem_load which register
i915_gem_inactive_shrink. If i915_driver_load fails after calling
i915_gem_load, the shrinker will be left registered. When called, it
will access freed memory and crash. The fix is to unregister the shrinker in the
failure path using code duplicated from i915_driver_unload.

i915_driver_load also has some incorrect gotos in the error cleanup
paths:

 * After failing to initialize the GTT (which cannot happen, btw,
   intel_gtt_get returns a fixed (non-NULL) value), it tries to
   free the uninitialized WC IO mapping. Fixed this by changing the
   target from out_iomapfree to out_rmmap
Signed-off-by: NKeith Packard <keithp@keithp.com>
Tested-by: NLin Ming <ming.m.lin@intel.com>

Signed-off-by: NJoe Perches <joe@perches.com>
Acked-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

[  191.310008] WARNING: kmemcheck: Caught 32-bit read from freed memory (f0d25f14)
[  191.310011] c056d2f088000000105fd2f00000000050415353040000000000000000000000
[  191.310020]  i i i i f f f f f f f f f f f f f f f f f f f f f f f f f f f f
[  191.310027]                                          ^
[  191.310029]
[  191.310032] Pid: 737, comm: modprobe Not tainted 3.0.0-rc5+ #268 Hewlett-Packard HP Compaq 6005 Pro SFF PC/3047h
[  191.310036] EIP: 0060:[<f80b3104>] EFLAGS: 00010286 CPU: 0
[  191.310039] EIP is at hp_wmi_perform_query+0x104/0x150 [hp_wmi]
[  191.310041] EAX: f0d25601 EBX: f0d25f00 ECX: 000121cf EDX: 000121ce
[  191.310043] ESI: f0d25f10 EDI: f0f97ea8 EBP: f0f97ec4 ESP: c173f34c
[  191.310045]  DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068
[  191.310046] CR0: 8005003b CR2: f540c000 CR3: 30f30000 CR4: 000006d0
[  191.310048] DR0: 00000000 DR1: 00000000 DR2: 00000000 DR3: 00000000
[  191.310050] DR6: ffff4ff0 DR7: 00000400
[  191.310051]  [<f80b317b>] hp_wmi_dock_state+0x2b/0x40 [hp_wmi]
[  191.310054]  [<f80b6093>] hp_wmi_init+0x93/0x1a8 [hp_wmi]
[  191.310057]  [<c10011f0>] do_one_initcall+0x30/0x170
[  191.310061]  [<c107ab9f>] sys_init_module+0xef/0x1a60
[  191.310064]  [<c149f998>] sysenter_do_call+0x12/0x28
[  191.310067]  [<ffffffff>] 0xffffffff
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Using buffer->output[1] without mutex_lock()
Signed-off-by: NJose Alonso <joalonsof@gmail.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

This reverts commit a3d77411,

as it causes a mess in the wireless rfkill status on some models.
It is probably a bad idea to toggle the rfkill for all dell models
without the respect to the claim that it is hardware-controlled.

Cc: stable@kernel.org
Signed-off-by: NKeng-Yu Lin <kengyu@canonical.com>
Signed-off-by: NMatthew Garrett <mjg@redhat.com>

Patch 2e711c04
(PM: Remove sysdev suspend, resume and shutdown operations)
deleted sysdev_suspend(), which was being relied on to call
check_wakeup_irqs() in suspend.  If check_wakeup_irqs() is not
called, wake interrupts that are pending when suspend is
entered may be lost.  It also breaks IRQCHIP_MASK_ON_SUSPEND,
which is handled in check_wakeup_irqs().

This patch adds a call to check_wakeup_irqs() in syscore_suspend(),
similar to what was deleted in sysdev_suspend().
Signed-off-by: NColin Cross <ccross@android.com>
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>

I came across a memory leak during a cyclic cpu-online-offline test.
Signed-off-by: NYu Luming <luming.yu@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NDave Jones <davej@redhat.com>

It is possible that a PMBus device supports the READ_TEMPERATURE2 and/or
READ_TEMPERATURE3 registers but does not support READ_TEMPERATURE1.
Improve temperature status register detection to address this condition.
Reported-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.39+

Negative temperatures were returned in degrees C instead of milli-Degrees C.
Also, negative temperatures were reported for remote temperature sensors even
if the chip was configured for positive-only results.

Fix by detecting temperature modes, and by treating negative temperatures
similar to positive temperatures, with appropriate sign extension.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+

When firewire-ohci is bound to a Pinnacle MovieBoard, eventually a
"Register access failure" is logged and an interrupt storm or a kernel
panic happens.  https://bugzilla.kernel.org/show_bug.cgi?id=36622

Until this is sorted out (if that is going to succeed at all), let's
just prevent firewire-ohci from touching these devices.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>

This driver handles the variants pca9530-pca9533, so it chose the name
"pca953x".  However, there is a gpio driver which decided on the same
name.  As a result, those two can't be loaded at the same time.  Add a
subsystem prefix to make the driver name unique.  Device matching will not
suffer, because both are I2C drivers which match using a
i2c_device_id-table which is not altered.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: Richard Purdie <richard.purdie@linuxfoundation.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes a regression in 3.0 reported by Paul Parsons regarding the
removal of the msleep(1) in the ds1wm_reset() function:

: The linux-3.0-rc4 DS1WM 1-wire driver is logging "bus error, retrying"
: error messages on an HP iPAQ hx4700 PDA (XScale-PXA270):
:
: <snip>
: Driver for 1-wire Dallas network protocol.
: DS1WM w1 busmaster driver - (c) 2004 Szabolcs Gyurko
: 1-Wire driver for the DS2760 battery monitor  chip  - (c) 2004-2005, Szabolcs Gyurko
: ds1wm ds1wm: pass: 1 bus error, retrying
: ds1wm ds1wm: pass: 2 bus error, retrying
: ds1wm ds1wm: pass: 3 bus error, retrying
: ds1wm ds1wm: pass: 4 bus error, retrying
: ds1wm ds1wm: pass: 5 bus error, retrying
: ...
:
: The visible result is that the battery charging LED is erratic; sometimes
: it works, mostly it doesn't.
:
: The linux-2.6.39 DS1WM 1-wire driver worked OK.  I haven't tried 3.0-rc1,
: 3.0-rc2, or 3.0-rc3.

This sleep should not be required on normal circuitry provided the
pull-ups on the bus are correctly adapted to the slaves.  Unfortunately,
this is not always the case.  The sleep is restored but as a parameter to
the probe function in the pdata.

[akpm@linux-foundation.org: coding-style fixes]
Reported-by: NPaul Parsons <lost.distance@yahoo.com>
Tested-by: NPaul Parsons <lost.distance@yahoo.com>
Signed-off-by: NJean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The LM95241 driver accepts every chip ID equal to or larger than 0xA4 as its
own, and other chips such as LM95245 use chip IDs in the accepted ID range.
This results in false chip detection.

Fix problem by accepting only the known LM95241 chip ID.
Signed-off-by: NGuenter Roeck <guenter.roeck@ericsson.com>
Acked-by: NJean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 2.6.30+

    
Multiple attempts to dynamically reallocate pci resources have
unfortunately lead to regressions. Though we continue to fix the
regressions and fine tune the dynamic-reallocation behavior, we have not
reached a acceptable state yet.
    
This patch provides a interim solution. It disables dynamic reallocation
by default, but adds the ability to enable it through pci=realloc kernel
command line parameter.
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NRam Pai <linuxram@us.ibm.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

The ramp_delay variable can be set lower than the desired value.
This patch fixes it.
Signed-off-by: NDonggeun Kim <dg77.kim@samsung.com>
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungMin Park <kyungmin.park@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Small cleanups for better readability.
Signed-off-by: NAxel Lin <axel.lin@gmail.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

The platform_data (pdata) may be pointing to __initdata section, which
may be free'd from the memory. The dependency on pdata in non-init
functions is removed in this patch to allow platform to declare
__initdata for platform data.
Signed-off-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Currently, ramp_delay variable is used uninitialzed in
max8997_set_voltage_ldobuck which gets called through
regulator_register calls.

To fix the problem, in max8997_pmic_probe, ramp_delay initialization
code is moved before calls to regulator_register.

Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: MyungJoo Ham <myungjoo.ham@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NTushar Behera <tushar.behera@linaro.org>
Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

Signed-off-by: NJonghwan Choi <jhbird.choi@samsung.com>
Acked-by: NMyungJoo Ham <myungjoo.ham@samsung.com>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NLiam Girdwood <lrg@slimlogic.co.uk>

We'll try again with the new fixes. Prepare to see this reverted when
we get regression reports...
Signed-off-by: NKeith Packard <keithp@keithp.com>

evergreen+ asics have 2-6 crtcs.  Don't access crtc registers
for crtc regs that don't exist as they have very high latency
and may cause problems on some asics.  The previous code missed
a few cases and was not fine grained enough (missed the 4 crtc
case for example).

Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=38800

v2: fix typo noticed by Chris Bandy <cbandy@jbandy.com>
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Reviewed-by: NMichel Dänzer <michel@daenzer.net>
Tested-by: NSimon Farnsworth <simon.farnsworth@onelan.co.uk>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Upon review, all path share the same dependencies for updating the
registers and so we can benefit from sharing the code and checking
early.

This removes the unsightly intel_wait_for_vblank() from the lowlevel
functions and upon further analysis the only path that will require a
wait is if we are performing an instantaneous transition between two
valid FBC configurations. The page-flip path itself will have disabled
FBC registers and will have waited for at least one vblank before
finishing the flip and attempting to re-enable FBC. This wait can be
accomplished simply by delaying the enable until after we are sure that
a vblank will have passed, which we are already doing to make sure that
the display is settled before enabling FBC.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>

In order to accommodate the requirements of re-enabling FBC after
page-flipping, but to avoid doing so and incurring the cost of a wait
for vblank in the middle of a page-flip sequence, we defer the actual
enablement by 50ms. If any request to disable FBC arrive within that
interval, the enablement is cancelled and we are saved from blocking on
the wait.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Page-flipping updates the scanout address, nukes the FBC compressed
image and so forces an FBC update so that the displayed image remains
consistent. However, page-flipping does not update the FBC registers
themselves, which remain pointing to both the old address and the old
CPU fence. Future updates to the new front-buffer (scanout) are then
undetected!

This first approach to demonstrate the issue and highlight the fix,
simply disables FBC upon page-flip (a recompression will be forced on
every flip so FBC becomes immaterial) and then re-enables FBC in the
page-flip finish work function, so that the FBC registers are now
pointing to the new framebuffer and front-buffer rendering works once
more.

Ideally, we want to only re-enable FBC after page-flipping is complete,
as otherwise we are just wasting cycles and power (with needless
recompression) whilst the page-flipping application is still running.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=33487Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Persistent mode is intended for use with front-buffer rendering, such as
X, where it is necessary to detect writes to the scanout either by the
GPU or through the CPU's fence, and recompress the dirty regions on the
fly. (By comparison to the back-buffer rendering, the scanout is always
recompressed after a page-flip.)

References: https://bugs.freedesktop.org/show_bug.cgi?id=33487
References: https://bugs.freedesktop.org/show_bug.cgi?id=31742Signed-off-by: NBen Widawsky <ben@bwidawsk.net>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NKeith Packard <keithp@keithp.com>

...and this requirement is enforced by intel_update_fbc() so we can
remove the later check from g4x_enable_fbc() and ironlake_enable_fbc().
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NKeith Packard <keithp@keithp.com>

The cfb_pitch was only used for 8xx_enable_fbc(), every later routine
was just overwriting the value with itself thanks to a copy'n'paste
error.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NKeith Packard <keithp@keithp.com>

...to ensure that any pending FBC enable tasklet is cancelled.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NKeith Packard <keithp@keithp.com>

As the enable/disable routines will be gain additional complexity in
future patches, it is necessary that all callers do not bypass the
generic interface by calling into the chipset routines directly. to do
this we make the chipset routines static, so there is no choice.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NKeith Packard <keithp@keithp.com>