Rely on the global ULPI register definitions
Signed-off-by: NHeikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Definitions for registers defined by ULPI specification v1.1.
Signed-off-by: NHeikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Mass Storage Function (MSF) used the same descriptors for each
usb_function instance (meaning usb_function::descriptors of different
functions pointed to the same static area (the same was true for
usb_function::hs_descriptors)).

This would leads to problems if MSF were used in several USB
configurations with different interface and/or endpoint numbers.
Descriptors for all configurations would have interface/endpoint
numbers overwritten by the values valid for the last configuration.

This patch adds code that copies the descriptors each time MSF is
added to USB configuration (that is for each usb_function).
Signed-off-by: NMichal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>

The composite framework allows gadgets with more than one function. This
can lead to situations where the configuration descriptor is larger than
the maximum of 512 bytes currently allowed by the composite framework.
This patch proposes to double that limit to 1024.
Signed-off-by: NRobert Lukassen <robert.lukassen@tomtom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds helper functions for ULPI access, and implements
otg_io_access_ops for musb.
Signed-off-by: NHeikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

EXTVBUS programming is required by OMAP3EVM REV >=E to supply 500mA
power so adding a flag which can be used by musb driver to program
EXTVBUS.
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove the unexistent CONFIG_USB_INVENTRA_MUSB_HAS_AHB_ID
option from our Makefile.

Problem reported by Sergei Shtylyov <sshtylyov@mvista.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

We don't need mach-types and hardware.h
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

get_cpu_rev() is unused in this driver. It is probably legacy
code. So remove it.
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These functions do nothing and also are both unnecessarily 'extern'; actually,
musb_platform_resume() in not even called...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This function is only called inside omap2430.c...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This function does nothing...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This function does nothing...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NCliff Cai <cliff.cai@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

when we fail to probe(), we can call musb_exit_debugfs().
Allow that by removing section annotations.
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All unsuccessful (non-zero status) URBs were being dropped. After N_IN_URBs are
dropped you will no longer be able to receive data.

This patch resubmits unsuccessful URBs unless the status indicates that it should
be terminated. The statuses that indicate the URB should be terminated was
gathered from other similar drivers.
Signed-off-by: NJames Maki <jamescmaki@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

g_hid is a USB gadget driver implementing the Human Interface Device class
specification. The driver handles basic HID protocol handling in the
kernel, and allows userspace to read/write HID reports trough /dev/hidgX
character devices.
Signed-off-by: NFabien Chouteau <fabien.chouteau@barco.com>
Signed-off-by: NPeter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove unnecessary comments stating function names at (some)
opening/closing braces.
Fix some whitespace issues.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Generalise write buffer preparation.

This allows for drivers to manipulate (e.g. add headers) to bulk out
data before it is sent.

This adds a new function pointer to usb_serial_driver:

int (*prepare_write_buffer)(struct usb_serial_port *port,
		void **dest, size_t size, const void *src, size_t count);

The function is generic and can be used with either kfifo-based or
multi-urb writes:

If *dest is NULL the implementation should allocate dest.
If src is NULL the implementation should use the port write fifo.

If not set, a generic implementation is used which simply uses memcpy or
kfifo_out.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use dynamic transfer buffer sizes since it is more efficient to let the
host controller do the partitioning to fit endpoint size. This way we
also do not use more than one urb per write request.

Replace max_in_flight_urbs with multi_urb_write flag in struct
usb_serial_driver to enable multi-urb writes.

Use MAX_TX_URBS=40 and a max buffer size of PAGE_SIZE to prevent DoS
attacks.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Allow drivers to implement their own multi-urb write bulk callbacks as
we do for single urb writes.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use the generic kfifo-based write implementation rather than allowing up
to 4000 8 byte urbs in the host stack queues.

Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use usb_serial_generic_close to kill the read and write urbs and to
reset the write fifo.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace custom fifo-based write implementation with the generic
kfifo-based one.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Submit write urb if it is not already in use and we have buffered data.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Clean up error messages on usb_submit_urb failure.
Remove debug message on zero-length writes.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Switch to generic read implementation and use process_read_urb to do
device specific processing (handle line status).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Allow drivers to use the generic throttle and unthrottle implementation.
This makes sense for drivers using the generic read functionality.

Note that drivers need to set these explicitly in order to enable them
(i.e., we do not set them at port probe if not defined).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use generic read implementation and use process_read_urb to do device
specific processing (handle line status).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add process_read_urb to usb_serial_driver so that a driver can rely on
the generic read (and throttle) mechanism but still do device specific
processing of incoming data (such as adding tty_flags before pushing to
line discipline).

The default generic implementation handles sysrq for consoles but
otherwise simply pushes to tty.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Always process and flush read urb, but only resubmit when not throttled.
The new tty-layer supply plenty of slack so there is really no need to
cache and delay processing of a single urb while throttled.

Note that unthrottle now submits using GFP_KERNEL as we are not in
atomic context (so there is no need to save irq state either).

Note also that the process_read_urb function could be added to
usb_serial_driver should any driver need to do any device specific
processing.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is no need to initialise the read urb as this is done at port
probe.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The generic read and write bulk urbs are initialised when allocated in
usb_serial_probe. The only field that needs to be updated after that is
the transfer_buffer_length of the write urb.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use the already exported function for submitting the read urb associated
with a usb_serial_port.

Make sure it returns the result of usb_submit_urb and rename to the
more descriptive usb_serial_generic_submit_read_urb.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Export usb_serial_generic_close so that drivers can easily kill the read
and write urb and make sure that the write fifo is reset.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure fifo is emptied on close.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On errors the fifo was reset without any locking. This could race with
write which do kfifo_put and perhaps also chars_in_buffer and write_room.

Every other access to the fifo is protected using the port lock so
better add it to the error path as well.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure chars_in_buffer accounts also for data in host stack queues.

This fixes the problem with tty_wait_until_sent returning too soon at
close which could cause the final write urb to be cancelled.
Reported-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The pl2303 requires a bulk-in buffer larger than endpoint size to keep
up at high baudrates without loosing data.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Increase the bulk-out buffer size from 64 to 256 byte.

This gives a significant increase in throughput already at 1Mbaud as well
as lowered CPU usage. The buffer is big enough to keep up also at 3Mbaud
(128b would not suffice).

        64b         256b
921k:   640 KB/s    870 KB/s
3M:     640 KB/s    2520 KB/s
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>