This reverts commit 28b45910 ("net: bcmgenet: Remove init parameter
from bcmgenet_mii_config") because in the process of moving from
dev_info() to dev_info_once() we essentially lost the helpful printed
messages once the second instance of the driver is loaded.
dev_info_once() does not actually print the message once per device
instance, but once period.

Fixes: 28b45910 ("net: bcmgenet: Remove init parameter from bcmgenet_mii_config")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NDoug Berger <opendmb@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the skb is attached to the first control block of a fragmented
skb it is possible that the skb could be freed when reclaiming that
control block before all fragments of the skb have been consumed by
the hardware and unmapped.

This commit introduces first_cb and last_cb pointers to the skb
control block used by the driver to keep track of which transmit
control blocks within a transmit ring are the first and last ones
associated with the skb.

It then splits the bcmgenet_free_cb() function into transmit
(bcmgenet_free_tx_cb) and receive (bcmgenet_free_rx_cb) versions
that can handle the unmapping of dma mapped memory and cleaning up
the corresponding control block structure so that the skb is only
freed after the last associated transmit control block is reclaimed.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

__bcmgenet_tx_reclaim() is currently summing TX bytes/packets in a way
that is not SMP friendly, mutliples CPUs could run
__bcmgenet_tx_reclaim() independently and still update stats->tx_bytes
and stats->tx_packets, cloberring the other CPUs statistics.

Fix this by tracking per RX and TX rings the number of bytes, packets,
dropped and errors statistics, and provide a bcmgenet_get_stats()
function which aggregates everything and returns a consistent output.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This commit adds support for the GENETv5 implementation.

The GENETv5 reports a major version of 6 instead of 5 so compensate
for this when verifying the configuration of the driver.  Also the
EPHY revision is now contained in the MDIO registers of the PHY so
the EPHY revision of 0 in GENET_VER_FMT is expected for GENETv5.
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a spinlock to ensure that irq0_stat is not unintentionally altered
as the result of preemption.  Also removed unserviced irq0 interrupts
and removed irq1_stat since there is no bottom half service for those
interrupts.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The location of the RBUF overflow and error counters has moved between
different version of the GENET MAC.  This commit corrects the driver to
read from the correct locations depending on the version of the GENET
MAC.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NDoug Berger <opendmb@gmail.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 62469c76 ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:

PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)

This was previously fixed by commit 5dbebbb4 ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.

Without commit 62469c76 we would have the following scenario after
an ifconfig down then up sequence:

- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
  initialized *before* we get to initialize the UniMAC, this is
  critical to ensure the PHY is in a correct state, priv->phydev is
  valid, this code executes fine

- second time from bcmgenet_mii_probe(), through the normal
  phy_init_hw() call (which arguably could be optimized out)

Everything is fine in that case. With commit 62469c76, we would have
the following scenario to happen after an ifconfig down then up
sequence:

- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
  NULL

- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
  bcmgenet_power_up() to initialize the internal PHY, the NULL check
  becomes true, so we do not reset the PHY, yet we keep going on and
  initialize the UniMAC, causing MAC activity to occur

- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
  too late, the PHY is botched, and causes the above bogus pings/packets
  transmission/reception to occur
Reported-by: NJaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 62469c76 ("net: ethernet: bcmgenet: use phydev
from struct net_device") because it causes GENETv1/2/3 adapters to
expose the following behavior after an ifconfig down/up sequence:

PING fainelli-linux (10.112.156.244): 56 data bytes
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.352 ms
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.472 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.496 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.517 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.536 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=1.557 ms (DUP!)
64 bytes from 10.112.156.244: seq=1 ttl=61 time=752.448 ms (DUP!)

This was previously fixed by commit 5dbebbb4 ("net: bcmgenet:
Software reset EPHY after power on") but the commit we are reverting was
essentially making this previous commit void, here is why.

Without commit 62469c76 we would have the following scenario after
an ifconfig down then up sequence:

- bcmgenet_open() calls bcmgenet_power_up() to make sure the PHY is
  initialized *before* we get to initialize the UniMAC, this is
  critical to ensure the PHY is in a correct state, priv->phydev is
  valid, this code executes fine

- second time from bcmgenet_mii_probe(), through the normal
  phy_init_hw() call (which arguably could be optimized out)

Everything is fine in that case. With commit 62469c76, we would have
the following scenario to happen after an ifconfig down then up
sequence:

- bcmgenet_close() calls phy_disonnect() which makes dev->phydev become
  NULL

- when bcmgenet_open() executes again and calls bcmgenet_mii_reset() from
  bcmgenet_power_up() to initialize the internal PHY, the NULL check
  becomes true, so we do not reset the PHY, yet we keep going on and
  initialize the UniMAC, causing MAC activity to occur

- we call bcmgenet_mii_reset() from bcmgenet_mii_probe(), but this is
  too late, the PHY is botched, and causes the above bogus pings/packets
  transmission/reception to occur
Reported-by: NJaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: NPhilippe Reynes <tremyfr@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Add bytes_compl local variable to __bcmgenet_tx_reclaim() to collect
   transmitted bytes. dev->stats updates can then be moved outside the
   while-loop. bytes_compl is also needed for future BQL support.
2. When bcmgenet device uses Tx checksum offload, each transmitted skb
   gets an extra 64-byte header prepended to it. Before this header is
   prepended to the skb, we need to save the skb "wire" length in
   GENET_CB(skb)->bytes_sent, so that proper Tx bytes accounting can
   be done in __bcmgenet_tx_reclaim().
3. skb->len covers the entire length of skb, whether it is linear or
   fragmented. Thus, when we clean the fragments, do not increase
   transmitted bytes.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The EPHY on GENET v1->v3 is extremely finicky, and will show occasional
failures based on the timing and reset sequence, ranging from duplicate
packets, to extremely high latencies.

Perform an additional software reset, and re-configuration to make sure it is
in a consistent and working state.

Fixes: 6ac3ce82 ("net: bcmgenet: Remove excessive PHY reset")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the ethtool rx-frames coalescing parameter which allows
defining the number of RX interrupts per frames received. The RDMA
engine supports a configurable timeout with a resolution of
approximately 8.192 us.

We can no longer enable the BDONE/PDONE interrupts as those would
fire for each packet/buffer received, which would defeat the MBDONE
interrupt purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Configuring the ethtool tx-frames property, which translates into N
packets before a TX interrupt is the simplest configuration scheme
because it requires no locking neither at the softare nor hardware
level, and is completely indepedent from the link speed. Since ethtool
does not allow per-tx queue coalescing parameters, we apply the same
setting to any transmit queue.

We can no longer enable the BDONE/PDONE interrupts as those would fire
for each packet/buffer received, which would defeat the MBDONE interrupt
purpose. The MBDONE interrupt is guaranteed to correspond to a
PDONE/BDONE interrupt when the threshold is set to 1, but offers
interrupt coalescing when the value is > 1.

Since the HW is configured to generate an interrupt when the ring
becomes emtpy, we have to deny any timeout/timer settings coming from
user-space to indicate we can only generate an interrupt very <N>
packets.

While we are at it, fix the DMA_INTR_THRESHOLD_MASK value which was off
by one bit (0xff vs. 0x1ff).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that we have reworked the way we perform the PHY initialization, we
no longer need to differentiate between init time vs. non-init time
calls, just use a dev_info_once() print to print the PHY type.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are currently doing a full PHY initialization and even starting the
pHY state machine during bcmgenet_mii_init() which is executed in the
driver's probe function. This is convenient to determine whether we can
attach to a proper PHY device but comes at the expense of spending up to
10ms per MDIO transactions (to reach the waitqueue timeout), which slows
things down.

This also creates a sitaution where we end-up attaching twice to the
PHY, which is not quite correct either.

Fix this by moving bcmgenet_mii_probe() into bcmgenet_open() and update
its error path accordingly.

Avoid printing the message "attached PHY at address 1 [...]" every time
we bring up/down the interface and remove this print since it duplicates
what the PHY driver already does for us.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Our internal GPHY might be powered off before we attempt scanning the
MDIO bus and bind a driver to it. The way we are currently determining
whether a PHY is internal or not is done *after* we have successfully
matched its driver. If the PHY is powered down, it will not respond to
the MDIO bus, so we will not be able to bind a driver to it.

Our Device Tree for GENET interfaces specifies a "phy-mode" value:
"internal" which tells if this internal uses an internal PHY or not.

If of_get_phy_mode() fails to parse the 'phy-mode' property, do an
additional manual lookup, and if we find "internal" set the
corresponding internal variable accordingly.

Replace all uses of phy_is_internal() with a check against
priv->internal_phy to avoid having to rely on whether or not
priv->phydev is set correctly.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are currently issuing multiple PHY resets during a suspend/resume,
first during bcmgenet_power_up() which does a hardware reset, then a
software reset by calling bcmgenet_mii_reset(). This is both unnecessary
and can take as long as 10ms per MDIO transactions while we re-apply
workarounds because we do not yet have MDIO interrupts enabled.

phy_resume() takes care of re-apply our workarounds in case we need any,
and bcmgenet_power_up() does a PHY hardware reset, all of this is more
than enough to guarantee that the PHY operates correctly.

Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All BCM7xxx integrated Gigabit PHYs have an issue in their MDIO
management controller which will make the initial read or write to them
to fail and return 0xffff. This is a real issue as the typical first
thing we do is read from MII_PHYSID1 and MII_PHYSID2 from get_phy_id()
to register a driver for these PHYs.

Coupled with the workaround in drivers/net/phy/bcm7xxx.c, this
workaround for the MDIO bus controller consists in scanning the list of
PHYs to do this initial read workaround for as part of the MDIO bus
reset routine which is invoked prior to mdiobus_scan().

Once we have a proper PHY driver/device registered, all workarounds are
located there (e.g: power management suspend/resume calls).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, MoCA fixed PHYs are always in link-up state, regardless of
whether the link is actually up or not.

Add code to properly detect MoCA link state changes and to reflect the
new state in MoCA fixed PHY. Only GENET V3 and V4 MACs are capable of
detecting MoCA link state changes.

The code works as follows:
1. GENET MAC detects MoCA link state change and issues UMAC_IRQ_LINK_UP
   or UMAC_IRQ_LINK_DOWN interrupt.
2. Link up/down interrupt is processed in bcmgenet_irq_task(), which
   calls phy_mac_interrupt().
3. phy_mac_interrupt() updates the fixed PHY phydev->link and kicks
   the PHY state machine.
4. PHY state machine proceeds to read the fixed PHY link status
   register.
5. When the fixed PHY link status register is being read, the new
   function bcmgenet_fixed_phy_link_update() gets called. It copies
   the fixed PHY phydev->link value to the fixed PHY status->link.
6. PHY state machine receives the new link state of the fixed PHY.
7. MoCA fixed PHY link state now correctly reflects the real MoCA
   hardware link state.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add #define UMAC_IRQ_LINK_EVENT to simplify link event handling code.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add #define for UMAC_IRQ_RXDMA_DONE and UMAC_IRQ_TXDMA_DONE in order
to simplify the code that handles Rx and Tx default queue interrupts.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for multiple Rx queues:
1. Add NAPI context per Rx queue
2. Modify Rx interrupt and Rx NAPI code to handle multiple Rx queues
Signed-off-by: NPetri Gynther <pgynther@google.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unnecessary function parameter priv. Use ring->priv instead.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unused priv->int0_mask and priv->int1_mask.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Power up the GPHY while we are bringing-up the network interface, and
conversely, upon bring down, power the GPHY down. In order to avoid
creating hardware hazards, make sure that the GPHY gets powered on
during bcmgenet_open() prior to the UniMAC being reset as the UniMAC may
start creating activity towards the GPHY if we reverse the steps.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CK25_DIS bit controls whether a 25Mhz clock is fed to the GPHY or
not, in preparation for powering down the integrated GPHY when relevant,
make sure we clear that bit.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for Hardware Filter Block (HFB) so that incoming Rx traffic
can be matched and directed to desired Rx queues.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bits 31:16 of RDMA_PROD_INDEX contain Rx discarded packet count, which
are the Rx packets that had to be dropped by MAC hardware since there
was no room on the Rx queue. Add code to collect this information into
the netdev stats.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Add struct bcmgenet_rx_ring to hold all necessary information
   for a single Rx queue.
2. Add bcmgenet_init_rx_queues() to initialize all Rx queues.
3. Modify bcmgenet_init_rx_ring() to initialize a single Rx queue.
4. Modify Rx interrupt path code to use per-queue data.
5. Modify bcmgenet_rx_refill() to use RxCB->bd_addr.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for supporting multiple Rx queues, add GENET_Q16_RX_BD_CNT
and hw_params->rx_bds_per_q.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

1. Use c_index and ring->c_index to determine how many TxCBs/TxBDs are
   ready for cleanup
   - c_index = the current value of TDMA_CONS_INDEX
   - TDMA_CONS_INDEX is HW-incremented and auto-wraparound (0x0-0xFFFF)
   - ring->c_index = __bcmgenet_tx_reclaim() cleaned up to this point on
     the previous invocation

2. Add bcmgenet_tx_ring->clean_ptr
   - index of the next TxCB to be cleaned
   - incremented as TxCBs/TxBDs are processed
   - value always in range [ring->cb_ptr, ring->end_ptr]

3. Fix incrementing of dev->stats.tx_packets
   - should be incremented only when tx_cb_ptr->skb != NULL

These changes simplify __bcmgenet_tx_reclaim(). Furthermore, Tx ring size
can now be any value.

With the old code, Tx ring size had to be a power-of-2:
   num_tx_bds = ring->size;
   c_index &= (num_tx_bds - 1);
   last_c_index &= (num_tx_bds - 1);
Signed-off-by: NPetri Gynther <pgynther@google.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds bcmgenet_tx_poll for the tx_rings. This can reduce the
interrupt load and send xmit in network stack on time. This also
separated for the completion of tx_ring16 from bcmgenet_poll.

The bcmgenet_tx_reclaim of tx_ring[{0,1,2,3}] operative by an interrupt
is to be not more than a certain number TxBDs. It is caused by too
slowly reclaiming the transmitted skb. Therefore, performance
degradation of xmit after 605ad7f1 ("tcp: refine TSO autosizing").
Signed-off-by: NJaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bcmgenet_hw_params->bds_cnt and GENET_DEFAULT_BD_CNT are used only in Tx init.
Rename them accordingly:
- bcmgenet_hw_params->bds_cnt => bcmgenet_hw_params->tx_bds_per_q
- GENET_DEFAULT_BD_CNT => GENET_Q16_TX_BD_CNT
Signed-off-by: NPetri Gynther <pgynther@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow enabling and disabling EEE using the designated ethtool getters
and setters. GENET allows controlling EEE at the UniMAC, RBUF and TBUF
levels. We also take care of restoring EEE after a suspend/resume cycle
if it was enabled prior to suspending.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add register definitions to control EEE in the UniMAC, RBUF and TBUF
register ranges.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To help troubleshoot heavy memory pressure conditions, add a bunch of
statistics counter to log RX buffer allocation and RX/TX DMA mapping
failures. These are reported like any other counters through the ethtool
stats interface.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case an interface has been brought down before entering S3, and then
brought up out of S3, all the initialization done during
bcmgenet_probe() by bcmgenet_mii_init() calling bcmgenet_mii_config() is
just lost since register contents are restored to their reset values.

Re-apply this configuration anytime we call bcmgenet_open() to make sure
our port multiplexer is properly configured to match the PHY interface.

Since we are now calling bcmgenet_mii_config() everytime bcmgenet_open()
is called, make sure we only print the message during initialization
time not to pollute the console.

Fixes: b6e978e5 ("net: bcmgenet: add suspend/resume callbacks")
Fixes: 1c1008c7 ("net: bcmgenet: add main driver file")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

phy_disconnect() is the only way to guarantee that we are not going to
schedule more work on the PHY state machine workqueue for that
particular PHY device.

This fixes an issue where a network interface was suspended prior to a
system suspend/resume cycle and would then be resumed as part of
mdio_bus_resume(), since the GENET interface clocks would have been
disabled, this basically resulted in bus errors to appear since we are
invoking the GENET driver adjust_link() callback.

Fixes: b6e978e5 ("net: bcmgenet: add suspend/resume callbacks")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GENET MAC has three Tx ring priority registers:
- GENET_x_TDMA_PRIORITY0 for queues 0-5
- GENET_x_TDMA_PRIORITY1 for queues 6-11
- GENET_x_TDMA_PRIORITY2 for queues 12-16

Fix bcmgenet_init_multiq() to program them correctly.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

bcmgenet_mii_setup() is called from the PHY state machine every 1-2 seconds
when the PHYs are in PHY_POLL mode.

Improve bcmgenet_mii_setup() so that it touches the MAC registers only when
the link is up and there was a change to link, speed, duplex, or pause status.
Signed-off-by: NPetri Gynther <pgynther@google.com>
Tested-by: NFlorian Fainelli <f.fainelli@gmail.com>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>