In smp_cpus_done() we need to call smp_ops->setup_cpu() for the boot
CPU, which means it has to run *on* the boot CPU.

In the past we ensured it ran on the boot CPU by changing the CPU
affinity mask of current directly. That was removed in commit
6d11b87d ("powerpc/smp: Replace open coded task affinity logic"),
and replaced with a work queue call.

Unfortunately using a work queue leads to a lockdep warning, now that
the CPU hotplug lock is a regular semaphore:

  ======================================================
  WARNING: possible circular locking dependency detected
  ...
  kworker/0:1/971 is trying to acquire lock:
   (cpu_hotplug_lock.rw_sem){++++++}, at: [<c000000000100974>] apply_workqueue_attrs+0x34/0xa0

  but task is already holding lock:
   ((&wfc.work)){+.+.+.}, at: [<c0000000000fdb2c>] process_one_work+0x25c/0x800
  ...
       CPU0                    CPU1
       ----                    ----
  lock((&wfc.work));
                               lock(cpu_hotplug_lock.rw_sem);
                               lock((&wfc.work));
  lock(cpu_hotplug_lock.rw_sem);

Although the deadlock can't happen in practice, because
smp_cpus_done() only runs in early boot before CPU hotplug is allowed,
lockdep can't tell that.

Luckily in commit 8fb12156 ("init: Pin init task to the boot CPU,
initially") tglx changed the generic code to pin init to the boot CPU
to begin with. The unpinning of init from the boot CPU happens in
sched_init_smp(), which is called after smp_cpus_done().

So smp_cpus_done() is always called on the boot CPU, which means we
don't need the work queue call at all - and the lockdep warning goes
away.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Reviewed-by: NThomas Gleixner <tglx@linutronix.de>

Implement an arch-speicfic watchdog rather than use the perf-based
hardlockup detector.

The new watchdog takes the soft-NMI directly, rather than going through
perf.  Perf interrupts are to be made maskable in future, so that would
prevent the perf detector from working in those regions.

Additionally, implement a SMP based detector where all CPUs watch one
another by pinging a shared cpumask.  This is because powerpc Book3S
does not have a true periodic local NMI, but some platforms do implement
a true NMI IPI.

If a CPU is stuck with interrupts hard disabled, the soft-NMI watchdog
does not work, but the SMP watchdog will.  Even on platforms without a
true NMI IPI to get a good trace from the stuck CPU, other CPUs will
notice the lockup sufficiently to report it and panic.

[npiggin@gmail.com: honor watchdog disable at boot/hotplug]
  Link: http://lkml.kernel.org/r/20170621001346.5bb337c9@roar.ozlabs.ibm.com
[npiggin@gmail.com: fix false positive warning at CPU unplug]
  Link: http://lkml.kernel.org/r/20170630080740.20766-1-npiggin@gmail.com
[akpm@linux-foundation.org: coding-style fixes]
Link: http://lkml.kernel.org/r/20170616065715.18390-6-npiggin@gmail.comSigned-off-by: NNicholas Piggin <npiggin@gmail.com>
Reviewed-by: NDon Zickus <dzickus@redhat.com>
Tested-by: Babu Moger <babu.moger@oracle.com>	[sparc]
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the different spin loop primitives in some simple powerpc
spin loops, including those which will spin as a common case.

This will help to test the spin loop primitives before more
conversions are done.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
[mpe: Add some includes of <linux/processor.h>]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

nr_cpu_ids can be limited by nr_cpus boot parameter, whereas NR_CPUS is a
compile time constant, which shouldn't be compared against during cpu kick.
Signed-off-by: NSantosh Sivaraj <santosh@fossix.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

During secondary start, we do not need to BUG_ON if an invalid CPU number
is passed. We already print an error if secondary cannot be started, so
just return an error instead.
Signed-off-by: NSantosh Sivaraj <santosh@fossix.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

To enable smp_processor_id() and might_sleep() debug checks earlier, it's
required to add system states between SYSTEM_BOOTING and SYSTEM_RUNNING.

Adjust the system_state check in smp_generic_cpu_bootable() to handle the
extra states.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: linuxppc-dev@lists.ozlabs.org
Link: http://lkml.kernel.org/r/20170516184735.359536998@linutronix.deSigned-off-by: NIngo Molnar <mingo@kernel.org>

This code was until recently completely undocumented and even now the comment is
not very verbose.

We've already had one patch sent to remove the IRQ enable/disable because it's
"paradoxical and unnecessary". So document it thoroughly to save anyone else
from puzzling over it.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Have the NMI IPI code use this op when the platform defines it.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Add a simple NMI IPI system that handles concurrency and reentrancy.

The platform does not have to implement a true non-maskable interrupt,
the default is to simply use the debugger break IPI message. This has
now been co-opted for a general IPI message, and users (debugger and
crash) have been reimplemented on top of the NMI system.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
[mpe: Incorporate incremental fixes from Nick]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Init task invokes smp_ops->setup_cpu() from smp_cpus_done(). Init task can
run on any online CPU at this point, but the setup_cpu() callback requires
to be invoked on the boot CPU. This is achieved by temporarily setting the
affinity of the calling user space thread to the requested CPU and reset it
to the original affinity afterwards.

That's racy vs. CPU hotplug and concurrent affinity settings for that
thread resulting in code executing on the wrong CPU and overwriting the
new affinity setting.

That's actually not a problem in this context as neither CPU hotplug nor
affinity settings can happen, but the access to task_struct::cpus_allowed
is about to restricted.

Replace it with a call to work_on_cpu_safe() which achieves the same result.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Lai Jiangshan <jiangshanlai@gmail.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Len Brown <lenb@kernel.org>
Link: http://lkml.kernel.org/r/20170412201042.518053336@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

POWER9 changes requirements and adds new instructions for
synchronization.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Change the doorbell callers to know about their msgsnd addressing,
rather than have them set a per-cpu target data tag at boot that gets
sent to the cause_ipi functions. The data is only used for doorbell IPI
functions, no other IPI types, so it makes sense to keep that detail
local to doorbell.

Have the platform code understand doorbell IPIs, rather than the
interrupt controller code understand them. Platform code can look at
capabilities it has available and decide which to use.
Signed-off-by: NNicholas Piggin <npiggin@gmail.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Some powerpc platforms use this to move IRQs away from a CPU being
unplugged. This function has several bugs such as not taking the right
locks or failing to NULL check pointers.

There's a new generic function doing exactly the same thing without all
the bugs, so let's use it instead.

mpe: The obvious place for the select of GENERIC_IRQ_MIGRATION is on
HOTPLUG_CPU, but that doesn't work. On some configs PM_SLEEP_SMP will
select HOTPLUG_CPU even though its dependencies are not met, which means
the select of GENERIC_IRQ_MIGRATION doesn't happen. That leads to the
build breaking. Fix it by moving the select of GENERIC_IRQ_MIGRATION to
SMP.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Some platforms (will) need to perform allocations before bringing
a new CPU online. Doing it from smp_ops->setup_cpu is the wrong
thing to do:

 - It has no useful failure path (too late)
 - Calling any allocator will enable interrupts prematurely
   causing problems with large decrementer among others

Instead, add a new callback that is called from __cpu_up (so from
the context trying to online the new CPU) at a point where we
can safely allocate and handle failures.

This will be used by XIVE support.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Move the following task->mm helper APIs into a new header file,
<linux/sched/mm.h>, to further reduce the size and complexity
of <linux/sched.h>.

Here are how the APIs are used in various kernel files:

  # mm_alloc():
  arch/arm/mach-rpc/ecard.c
  fs/exec.c
  include/linux/sched/mm.h
  kernel/fork.c

  # __mmdrop():
  arch/arc/include/asm/mmu_context.h
  include/linux/sched/mm.h
  kernel/fork.c

  # mmdrop():
  arch/arm/mach-rpc/ecard.c
  arch/m68k/sun3/mmu_emu.c
  arch/x86/mm/tlb.c
  drivers/gpu/drm/amd/amdkfd/kfd_process.c
  drivers/gpu/drm/i915/i915_gem_userptr.c
  drivers/infiniband/hw/hfi1/file_ops.c
  drivers/vfio/vfio_iommu_spapr_tce.c
  fs/exec.c
  fs/proc/base.c
  fs/proc/task_mmu.c
  fs/proc/task_nommu.c
  fs/userfaultfd.c
  include/linux/mmu_notifier.h
  include/linux/sched/mm.h
  kernel/fork.c
  kernel/futex.c
  kernel/sched/core.c
  mm/khugepaged.c
  mm/ksm.c
  mm/mmu_context.c
  mm/mmu_notifier.c
  mm/oom_kill.c
  virt/kvm/kvm_main.c

  # mmdrop_async_fn():
  include/linux/sched/mm.h

  # mmdrop_async():
  include/linux/sched/mm.h
  kernel/fork.c

  # mmget_not_zero():
  fs/userfaultfd.c
  include/linux/sched/mm.h
  mm/oom_kill.c

  # mmput():
  arch/arc/include/asm/mmu_context.h
  arch/arc/kernel/troubleshoot.c
  arch/frv/mm/mmu-context.c
  arch/powerpc/platforms/cell/spufs/context.c
  arch/sparc/include/asm/mmu_context_32.h
  drivers/android/binder.c
  drivers/gpu/drm/etnaviv/etnaviv_gem.c
  drivers/gpu/drm/i915/i915_gem_userptr.c
  drivers/infiniband/core/umem.c
  drivers/infiniband/core/umem_odp.c
  drivers/infiniband/core/uverbs_main.c
  drivers/infiniband/hw/mlx4/main.c
  drivers/infiniband/hw/mlx5/main.c
  drivers/infiniband/hw/usnic/usnic_uiom.c
  drivers/iommu/amd_iommu_v2.c
  drivers/iommu/intel-svm.c
  drivers/lguest/lguest_user.c
  drivers/misc/cxl/fault.c
  drivers/misc/mic/scif/scif_rma.c
  drivers/oprofile/buffer_sync.c
  drivers/vfio/vfio_iommu_type1.c
  drivers/vhost/vhost.c
  drivers/xen/gntdev.c
  fs/exec.c
  fs/proc/array.c
  fs/proc/base.c
  fs/proc/task_mmu.c
  fs/proc/task_nommu.c
  fs/userfaultfd.c
  include/linux/sched/mm.h
  kernel/cpuset.c
  kernel/events/core.c
  kernel/events/uprobes.c
  kernel/exit.c
  kernel/fork.c
  kernel/ptrace.c
  kernel/sys.c
  kernel/trace/trace_output.c
  kernel/tsacct.c
  mm/memcontrol.c
  mm/memory.c
  mm/mempolicy.c
  mm/migrate.c
  mm/mmu_notifier.c
  mm/nommu.c
  mm/oom_kill.c
  mm/process_vm_access.c
  mm/rmap.c
  mm/swapfile.c
  mm/util.c
  virt/kvm/async_pf.c

  # mmput_async():
  include/linux/sched/mm.h
  kernel/fork.c
  mm/oom_kill.c

  # get_task_mm():
  arch/arc/kernel/troubleshoot.c
  arch/powerpc/platforms/cell/spufs/context.c
  drivers/android/binder.c
  drivers/gpu/drm/etnaviv/etnaviv_gem.c
  drivers/infiniband/core/umem.c
  drivers/infiniband/core/umem_odp.c
  drivers/infiniband/hw/mlx4/main.c
  drivers/infiniband/hw/mlx5/main.c
  drivers/infiniband/hw/usnic/usnic_uiom.c
  drivers/iommu/amd_iommu_v2.c
  drivers/iommu/intel-svm.c
  drivers/lguest/lguest_user.c
  drivers/misc/cxl/fault.c
  drivers/misc/mic/scif/scif_rma.c
  drivers/oprofile/buffer_sync.c
  drivers/vfio/vfio_iommu_type1.c
  drivers/vhost/vhost.c
  drivers/xen/gntdev.c
  fs/proc/array.c
  fs/proc/base.c
  fs/proc/task_mmu.c
  include/linux/sched/mm.h
  kernel/cpuset.c
  kernel/events/core.c
  kernel/exit.c
  kernel/fork.c
  kernel/ptrace.c
  kernel/sys.c
  kernel/trace/trace_output.c
  kernel/tsacct.c
  mm/memcontrol.c
  mm/memory.c
  mm/mempolicy.c
  mm/migrate.c
  mm/mmu_notifier.c
  mm/nommu.c
  mm/util.c

  # mm_access():
  fs/proc/base.c
  include/linux/sched/mm.h
  kernel/fork.c
  mm/process_vm_access.c

  # mm_release():
  arch/arc/include/asm/mmu_context.h
  fs/exec.c
  include/linux/sched/mm.h
  include/uapi/linux/sched.h
  kernel/exit.c
  kernel/fork.c
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

We are going to split <linux/sched/topology.h> out of <linux/sched.h>, which
will have to be picked up from other headers and a couple of .c files.

Create a trivial placeholder <linux/sched/topology.h> file that just
maps to <linux/sched.h> to make this patch obviously correct and
bisectable.

Include the new header in the files that are going to need it.
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

So the original intention of tsk_cpus_allowed() was to 'future-proof'
the field - but it's pretty ineffectual at that, because half of
the code uses ->cpus_allowed directly ...

Also, the wrapper makes the code longer than the original expression!

So just get rid of it. This also shrinks <linux/sched.h> a bit.
Acked-by: NLinus Torvalds <torvalds@linux-foundation.org>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NIngo Molnar <mingo@kernel.org>

Apart from adding the helper function itself, the rest of the kernel is
converted mechanically using:

  git grep -l 'atomic_inc.*mm_count' | xargs sed -i 's/atomic_inc(&\(.*\)->mm_count);/mmgrab\(\1\);/'
  git grep -l 'atomic_inc.*mm_count' | xargs sed -i 's/atomic_inc(&\(.*\)\.mm_count);/mmgrab\(\&\1\);/'

This is needed for a later patch that hooks into the helper, but might
be a worthwhile cleanup on its own.

(Michal Hocko provided most of the kerneldoc comment.)

Link: http://lkml.kernel.org/r/20161218123229.22952-1-vegard.nossum@oracle.comSigned-off-by: NVegard Nossum <vegard.nossum@oracle.com>
Acked-by: NMichal Hocko <mhocko@suse.com>
Acked-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: NDavid Rientjes <rientjes@google.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 2965faa5 ("kexec: split kexec_load syscall from kexec core
code") introduced CONFIG_KEXEC_CORE so that CONFIG_KEXEC means whether
the kexec_load system call should be compiled-in and CONFIG_KEXEC_FILE
means whether the kexec_file_load system call should be compiled-in.
These options can be set independently from each other.

Since until now powerpc only supported kexec_load, CONFIG_KEXEC and
CONFIG_KEXEC_CORE were synonyms. That is not the case anymore, so we
need to make a distinction. Almost all places where CONFIG_KEXEC was
being used should be using CONFIG_KEXEC_CORE instead, since
kexec_file_load also needs that code compiled in.
Signed-off-by: NThiago Jung Bauermann <bauerman@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

We observed a kernel oops when running a PPC guest with config NR_CPUS=4
and qemu option "-smp cores=1,threads=8":

[   30.634781] Unable to handle kernel paging request for data at
address 0xc00000014192eb17
[   30.636173] Faulting instruction address: 0xc00000000003e5cc
[   30.637069] Oops: Kernel access of bad area, sig: 11 [#1]
[   30.637877] SMP NR_CPUS=4 NUMA pSeries
[   30.638471] Modules linked in:
[   30.638949] CPU: 3 PID: 27 Comm: migration/3 Not tainted
4.7.0-07963-g9714b26 #1
[   30.640059] task: c00000001e29c600 task.stack: c00000001e2a8000
[   30.640956] NIP: c00000000003e5cc LR: c00000000003e550 CTR:
0000000000000000
[   30.642001] REGS: c00000001e2ab8e0 TRAP: 0300   Not tainted
(4.7.0-07963-g9714b26)
[   30.643139] MSR: 8000000102803033 <SF,VEC,VSX,FP,ME,IR,DR,RI,LE,TM[E]>  CR: 22004084  XER: 00000000
[   30.644583] CFAR: c000000000009e98 DAR: c00000014192eb17 DSISR: 40000000 SOFTE: 0
GPR00: c00000000140a6b8 c00000001e2abb60 c0000000016dd300 0000000000000003
GPR04: 0000000000000000 0000000000000004 c0000000016e5920 0000000000000008
GPR08: 0000000000000004 c00000014192eb17 0000000000000000 0000000000000020
GPR12: c00000000140a6c0 c00000000ffffc00 c0000000000d3ea8 c00000001e005680
GPR16: 0000000000000000 0000000000000000 0000000000000000 0000000000000000
GPR20: 0000000000000000 c00000001e6b3a00 0000000000000000 0000000000000001
GPR24: c00000001ff85138 c00000001ff85130 000000001eb6f000 0000000000000001
GPR28: 0000000000000000 c0000000017014e0 0000000000000000 0000000000000018
[   30.653882] NIP [c00000000003e5cc] __cpu_disable+0xcc/0x190
[   30.654713] LR [c00000000003e550] __cpu_disable+0x50/0x190
[   30.655528] Call Trace:
[   30.655893] [c00000001e2abb60] [c00000000003e550] __cpu_disable+0x50/0x190 (unreliable)
[   30.657280] [c00000001e2abbb0] [c0000000000aca0c] take_cpu_down+0x5c/0x100
[   30.658365] [c00000001e2abc10] [c000000000163918] multi_cpu_stop+0x1a8/0x1e0
[   30.659617] [c00000001e2abc60] [c000000000163cc0] cpu_stopper_thread+0xf0/0x1d0
[   30.660737] [c00000001e2abd20] [c0000000000d8d70] smpboot_thread_fn+0x290/0x2a0
[   30.661879] [c00000001e2abd80] [c0000000000d3fa8] kthread+0x108/0x130
[   30.662876] [c00000001e2abe30] [c000000000009968] ret_from_kernel_thread+0x5c/0x74
[   30.664017] Instruction dump:
[   30.664477] 7bde1f24 38a00000 787f1f24 3b600001 39890008 7d204b78 7d05e214 7d0b07b4
[   30.665642] 796b1f24 7d26582a 7d204a14 7d29f214 <7d4048a8> 7d4a3878 7d4049ad 40c2fff4
[   30.666854] ---[ end trace 32643b7195717741 ]---

The reason of this is that in __cpu_disable(), when we try to set the
cpu_sibling_mask or cpu_core_mask of the sibling CPUs of the disabled
one, we don't check whether the current configuration employs those
sibling CPUs(hw threads). And if a CPU is not employed by a
configuration, the percpu structures cpu_{sibling,core}_mask are not
allocated, therefore accessing those cpumasks will result in problems as
above.

This patch fixes this problem by adding an addition check on whether the
id is no less than nr_cpu_ids in the sibling CPU iteration code.
Signed-off-by: NBoqun Feng <boqun.feng@gmail.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>

We plan to use jump label for cpu_has_feature(). In order to implement
this we need to include the linux/jump_label.h in asm/cputable.h.

Unfortunately if we do that it leads to an include loop. The root of the
problem seems to be that reg.h needs cputable.h (for CPU_FTRs), and then
cputable.h via jump_label.h eventually pulls in hw_irq.h which needs
reg.h (for MSR_EE).

So move cpu_has_feature() to a separate file on its own.
Signed-off-by: NKevin Hao <haokexin@gmail.com>
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
[mpe: Rename to cpu_has_feature.h and flesh out change log]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Export cpu_to_core_id(). This will be used by the lpfc driver.

This enables topology_core_id() from <linux/topology.h> (defined
to cpu_to_core_id() in arch/powerpc/include/asm/topology.h) to be
used by (non-builtin) modules.

That is arch-neutral, already used by eg, drivers/base/topology.c,
but it is builtin (obj-y in Makefile) thus didn't need the export.

Since the module uses topology_core_id() and this is defined to
cpu_to_core_id(), it needs the export, otherwise:

    ERROR: "cpu_to_core_id" [drivers/scsi/lpfc/lpfc.ko] undefined!

Tested on next-20160601.
Signed-off-by: NMauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Sometimes headers that provide prototypes for functions are
accidentally omitted from the files that define the functions.

Fix a couple of times that occurs.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Sparse picked up a number of functions that are implemented in C and
then only referred to in asm code.

This introduces asm-prototypes.h, which provides a place for
prototypes of these functions.

This silences some sparse warnings.
Signed-off-by: NDaniel Axtens <dja@axtens.net>
[mpe: Add include guards, clean up copyright & GPL text]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

In order to enable symmetric hotplug, we must mirror the online &&
!active state of cpu-down on the cpu-up side.

However, to retain sanity, limit this state to per-cpu kthreads.

Aside from the change to set_cpus_allowed_ptr(), which allow moving
the per-cpu kthreads on, the other critical piece is the cpu selection
for pinned tasks in select_task_rq(). This avoids dropping into
select_fallback_rq().

select_fallback_rq() cannot be allowed to select !active cpus because
its used to migrate user tasks away. And we do not want to move user
tasks onto cpus that are in transition.
Requested-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Tested-by: NThomas Gleixner <tglx@linutronix.de>
Cc: Lai Jiangshan <laijs@cn.fujitsu.com>
Cc: Jan H. Schönherr <jschoenh@amazon.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160301152303.GV6356@twins.programming.kicks-ass.netSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

Freescale E500MC and E5500 core-based platforms, like P4080, T1040,
support disabling/enabling CPU dynamically.
This patch adds this feature on those platforms.
Signed-off-by: NChenhui Zhao <chenhui.zhao@freescale.com>
Signed-off-by: NTang Yuantian <Yuantian.Tang@feescale.com>
[scottwood: removed unused pr_fmt]
Signed-off-by: NScott Wood <oss@buserror.net>

Let the non boot cpus call into idle with the corresponding hotplug state, so
the hotplug core can handle the further bringup. That's a first step to
convert the boot side of the hotplugged cpus to do all the synchronization
with the other side through the state machine. For now it'll only start the
hotplug thread and kick the full bringup of the cpu.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: Rik van Riel <riel@redhat.com>
Cc: Rafael Wysocki <rafael.j.wysocki@intel.com>
Cc: "Srivatsa S. Bhat" <srivatsa@mit.edu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Paul McKenney <paulmck@linux.vnet.ibm.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul Turner <pjt@google.com>
Link: http://lkml.kernel.org/r/20160226182341.614102639@linutronix.deSigned-off-by: NThomas Gleixner <tglx@linutronix.de>

This patch adds support to real-mode KVM to search for a core
running in the host partition and send it an IPI message with
VCPU to be woken. This avoids having to switch to the host
partition to complete an H_IPI hypercall when the VCPU which
is the target of the the H_IPI is not loaded (is not running
in the guest).

The patch also includes the support in the IPI handler running
in the host to do the wakeup by calling kvmppc_xics_ipi_action
for the PPC_MSG_RM_HOST_ACTION message.

When a guest is being destroyed, we need to ensure that there
are no pending IPIs waiting to wake up a VCPU before we free
the VCPUs of the guest. This is accomplished by:
- Forces a PPC_MSG_CALL_FUNCTION IPI to be completed by all CPUs
  before freeing any VCPUs in kvm_arch_destroy_vm().
- Any PPC_MSG_RM_HOST_ACTION messages must be executed first
  before any other PPC_MSG_CALL_FUNCTION messages.
Signed-off-by: NSuresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

smp_muxed_ipi_message_pass() invokes smp_ops->cause_ipi, which
uses an ioremapped address to access registers on the XICS
interrupt controller to cause the IPI. Because of this real
mode callers cannot call smp_muxed_ipi_message_pass() for IPI
messaging.

This patch creates a separate function smp_muxed_ipi_set_message
just to set the IPI message without the cause_ipi routine.
After calling this function to set the IPI message, real
mode callers must cause the IPI by writing to the XICS registers
directly.

As part of this, we also change smp_muxed_ipi_message_pass
to call smp_muxed_ipi_set_message to set the message instead
of doing it directly inside the routine.
Signed-off-by: NSuresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch increases the number of demuxed messages for a
controller with a single ipi to 8 for 64-bit systems.

This is required because we want to use the IPI mechanism
to send messages from a CPU running in KVM real mode in a
guest to a CPU in the host to take some action. Currently,
we only support 4 messages and all 4 are already taken.

Define a fifth message PPC_MSG_RM_HOST_ACTION for this
purpose.
Signed-off-by: NSuresh Warrier <warrier@linux.vnet.ibm.com>
Acked-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Anton has a busy ppc64le KVM box where guests sometimes hit the infamous
"kernel BUG at kernel/smpboot.c:134!" issue during boot:

  BUG_ON(td->cpu != smp_processor_id());

Basically a per CPU hotplug thread scheduled on the wrong CPU. The oops
output confirms it:

  CPU: 0
  Comm: watchdog/130

The problem is that we aren't ensuring the CPU active bit is set for the
secondary before allowing the master to continue on. The master unparks
the secondary CPU's kthreads and the scheduler looks for a CPU to run
on. It calls select_task_rq() and realises the suggested CPU is not in
the cpus_allowed mask. It then ends up in select_fallback_rq(), and
since the active bit isnt't set we choose some other CPU to run on.

This seems to have been introduced by 6acbfb96 "sched: Fix hotplug
vs. set_cpus_allowed_ptr()", which changed from setting active before
online to setting active after online. However that was in turn fixing a
bug where other code assumed an active CPU was also online, so we can't
just revert that fix.

The simplest fix is just to spin waiting for both active & online to be
set. We already have a barrier prior to set_cpu_online() (which also
sets active), to ensure all other setup is completed before online &
active are set.

Fixes: 6acbfb96 ("sched: Fix hotplug vs. set_cpus_allowed_ptr()")
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Remove slice_set_psize() which is not used.

It was added in 3a8247cc "powerpc: Only demote individual slices
rather than whole process" but was never used.

Remove vsx_assist_exception() which is not used.

It was added in ce48b210 "powerpc: Add VSX context save/restore,
ptrace and signal support" but was never used.

Remove generic_mach_cpu_die() which is not used.

Its last caller was removed in 375f561a "powerpc/powernv: Always go
into nap mode when CPU is offline".

Remove mpc7448_hpc2_power_off() and mpc7448_hpc2_halt() which are
unused.

These were introduced in c5d56332 "[POWERPC] Add general support for
mpc7448hpc2 (Taiga) platform" but were never used.

This was partially found by using a static code analysis program called
cppcheck.
Signed-off-by: NRickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
[mpe: Update changelog with details on when/why they are unused]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This reverts commit 7c5c92ed.

Although this did fix the bug it was aimed at, it also broke secondary
startup on platforms that use give/take_timebase(). Unfortunately we
didn't detect that while it was in next.
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

I have a busy ppc64le KVM box where guests sometimes hit the infamous
"kernel BUG at kernel/smpboot.c:134!" issue during boot:

  BUG_ON(td->cpu != smp_processor_id());

Basically a per CPU hotplug thread scheduled on the wrong CPU. The oops
output confirms it:

  CPU: 0
  Comm: watchdog/130

The problem is that we aren't ensuring the CPU active and online bits are set
before allowing the master to continue on. The master unparks the secondary
CPUs kthreads and the scheduler looks for a CPU to run on. It calls
select_task_rq and realises the suggested CPU is not in the cpus_allowed
mask. It then ends up in select_fallback_rq, and since the active and
online bits aren't set we choose some other CPU to run on.

Cc: stable@vger.kernel.org
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This still has not been merged and now powerpc is the only arch that does
not have this change. Sorry about missing linuxppc-dev before.

V2->V2
  - Fix up to work against 3.18-rc1

__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x).  This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.

Other use cases are for storing and retrieving data from the current
processors percpu area.  __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.

__get_cpu_var() is defined as :

__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.

this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.

This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset.  Thereby address calculations are avoided and less registers
are used when code is generated.

At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.

The patch set includes passes over all arches as well. Once these operations
are used throughout then specialized macros can be defined in non -x86
arches as well in order to optimize per cpu access by f.e.  using a global
register that may be set to the per cpu base.

Transformations done to __get_cpu_var()

1. Determine the address of the percpu instance of the current processor.

	DEFINE_PER_CPU(int, y);
	int *x = &__get_cpu_var(y);

    Converts to

	int *x = this_cpu_ptr(&y);

2. Same as #1 but this time an array structure is involved.

	DEFINE_PER_CPU(int, y[20]);
	int *x = __get_cpu_var(y);

    Converts to

	int *x = this_cpu_ptr(y);

3. Retrieve the content of the current processors instance of a per cpu
variable.

	DEFINE_PER_CPU(int, y);
	int x = __get_cpu_var(y)

   Converts to

	int x = __this_cpu_read(y);

4. Retrieve the content of a percpu struct

	DEFINE_PER_CPU(struct mystruct, y);
	struct mystruct x = __get_cpu_var(y);

   Converts to

	memcpy(&x, this_cpu_ptr(&y), sizeof(x));

5. Assignment to a per cpu variable

	DEFINE_PER_CPU(int, y)
	__get_cpu_var(y) = x;

   Converts to

	__this_cpu_write(y, x);

6. Increment/Decrement etc of a per cpu variable

	DEFINE_PER_CPU(int, y);
	__get_cpu_var(y)++

   Converts to

	__this_cpu_inc(y)

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: NChristoph Lameter <cl@linux.com>
[mpe: Fix build errors caused by set/or_softirq_pending(), and rework
      assignment in __set_breakpoint() to use memcpy().]
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

As Nish suggested, it makes more sense to init the numa node informatiion
for present cpus at boottime, which could also avoid WARN_ON(1) in
numa_setup_cpu().

With this change, we also need to change the smp_prepare_cpus() to set up
numa information only on present cpus.

For those possible, but not present cpus, their numa information
will be set up after they are started, as the original code did before commit
2fabf084.

Cc: Nishanth Aravamudan <nacc@linux.vnet.ibm.com>
Cc: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: NLi Zhong <zhong@linux.vnet.ibm.com>
Acked-by: NNishanth Aravamudan <nacc@linux.vnet.ibm.com>
Tested-by: NCyril Bur <cyril.bur@au1.ibm.com>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

Fix a number of places where global functions were not including
their prototype. This ensures the prototype and the function match.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NMichael Ellerman <mpe@ellerman.id.au>

This reverts commit 5828f666 due to
build failure after merging with pending powerpc changes.

Link: http://lkml.kernel.org/g/20140827142243.6277eaff@canb.auug.org.auSigned-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>

__get_cpu_var() is used for multiple purposes in the kernel source. One of
them is address calculation via the form &__get_cpu_var(x).  This calculates
the address for the instance of the percpu variable of the current processor
based on an offset.

Other use cases are for storing and retrieving data from the current
processors percpu area.  __get_cpu_var() can be used as an lvalue when
writing data or on the right side of an assignment.

__get_cpu_var() is defined as :

#define __get_cpu_var(var) (*this_cpu_ptr(&(var)))

__get_cpu_var() always only does an address determination. However, store
and retrieve operations could use a segment prefix (or global register on
other platforms) to avoid the address calculation.

this_cpu_write() and this_cpu_read() can directly take an offset into a
percpu area and use optimized assembly code to read and write per cpu
variables.

This patch converts __get_cpu_var into either an explicit address
calculation using this_cpu_ptr() or into a use of this_cpu operations that
use the offset.  Thereby address calculations are avoided and less registers
are used when code is generated.

At the end of the patch set all uses of __get_cpu_var have been removed so
the macro is removed too.

The patch set includes passes over all arches as well. Once these operations
are used throughout then specialized macros can be defined in non -x86
arches as well in order to optimize per cpu access by f.e.  using a global
register that may be set to the per cpu base.

Transformations done to __get_cpu_var()

1. Determine the address of the percpu instance of the current processor.

	DEFINE_PER_CPU(int, y);
	int *x = &__get_cpu_var(y);

    Converts to

	int *x = this_cpu_ptr(&y);

2. Same as #1 but this time an array structure is involved.

	DEFINE_PER_CPU(int, y[20]);
	int *x = __get_cpu_var(y);

    Converts to

	int *x = this_cpu_ptr(y);

3. Retrieve the content of the current processors instance of a per cpu
variable.

	DEFINE_PER_CPU(int, y);
	int x = __get_cpu_var(y)

   Converts to

	int x = __this_cpu_read(y);

4. Retrieve the content of a percpu struct

	DEFINE_PER_CPU(struct mystruct, y);
	struct mystruct x = __get_cpu_var(y);

   Converts to

	memcpy(&x, this_cpu_ptr(&y), sizeof(x));

5. Assignment to a per cpu variable

	DEFINE_PER_CPU(int, y)
	__get_cpu_var(y) = x;

   Converts to

	__this_cpu_write(y, x);

6. Increment/Decrement etc of a per cpu variable

	DEFINE_PER_CPU(int, y);
	__get_cpu_var(y)++

   Converts to

	__this_cpu_inc(y)

tj: Folded a fix patch.
    http://lkml.kernel.org/g/alpine.DEB.2.11.1408172143020.9652@gentwo.org

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Paul Mackerras <paulus@samba.org>
Signed-off-by: NChristoph Lameter <cl@linux.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

There is an issue currently where NUMA information is used on powerpc
(and possibly ia64) before it has been read from the device-tree, which
leads to large slab consumption with CONFIG_SLUB and memoryless nodes.

NUMA powerpc non-boot CPU's cpu_to_node/cpu_to_mem is only accurate
after start_secondary(), similar to ia64, which is invoked via
smp_init().

Commit 6ee0578b ("workqueue: mark init_workqueues() as
early_initcall()") made init_workqueues() be invoked via
do_pre_smp_initcalls(), which is obviously before the secondary
processors are online.

Additionally, the following commits changed init_workqueues() to use
cpu_to_node to determine the node to use for kthread_create_on_node:

bce90380 ("workqueue: add wq_numa_tbl_len and
wq_numa_possible_cpumask[]")
f3f90ad4 ("workqueue: determine NUMA node of workers accourding to
the allowed cpumask")

Therefore, when init_workqueues() runs, it sees all CPUs as being on
Node 0. On LPARs or KVM guests where Node 0 is memoryless, this leads to
a high number of slab deactivations
(http://www.spinics.net/lists/linux-mm/msg67489.html).

Fix this by initializing the powerpc-specific CPU<->node/local memory
node mapping as early as possible, which on powerpc is
do_init_bootmem(). Currently that function initializes the mapping for
the boot CPU, but we extend it to setup the mapping for all possible
CPUs. Then, in smp_prepare_cpus(), we can correspondingly set the
per-cpu values for all possible CPUs. That ensures that before the
early_initcalls run (and really as early as possible), the per-cpu NUMA
mapping is accurate.

While testing memoryless nodes on PowerKVM guests with a fix to the
workqueue logic to use cpu_to_mem() instead of cpu_to_node(), with a
guest topology of:

available: 2 nodes (0-1)
node 0 cpus: 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49
node 0 size: 0 MB
node 0 free: 0 MB
node 1 cpus: 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99
node 1 size: 16336 MB
node 1 free: 15329 MB
node distances:
node   0   1
  0:  10  40
  1:  40  10

the slab consumption decreases from

Slab:             932416 kB
SUnreclaim:       902336 kB

to

Slab:             395264 kB
SUnreclaim:       359424 kB

And we a corresponding increase in the slab efficiency from

slab                                   mem     objs    slabs
                                      used   active   active
------------------------------------------------------------
kmalloc-16384                       337 MB   11.28%  100.00%
task_struct                         288 MB    9.93%  100.00%

to

slab                                   mem     objs    slabs
                                      used   active   active
------------------------------------------------------------
kmalloc-16384                        37 MB  100.00%  100.00%
task_struct                          31 MB  100.00%  100.00%

Powerpc didn't support memoryless nodes until recently (64bb80d8
"powerpc/numa: Enable CONFIG_HAVE_MEMORYLESS_NODES" and 8c272261
"powerpc/numa: Enable USE_PERCPU_NUMA_NODE_ID"). Those commits also
helped improve memory consumption with these kind of environments.
Signed-off-by: NNishanth Aravamudan <nacc@linux.vnet.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>