The CNE bits are inverted on the device and writeb function is missing a
NOT operation.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Remove the not longer supported NO_VIRTBLOCKS flag and remove
an unused variable while at it.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The nand_oobinfo structure is not fitting the newer error correction
demands anymore. Replace it by struct nand_ecclayout and fixup the users
all over the place. Keep the nand_oobinfo based ioctl for user space
compability reasons.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The hwcontrol function enforced a step by step state machine
for any kind of hardware chip access. Let the hardware driver
know which control bits are set and inform it about a change
of the control lines. Let the hardware driver write out the
command and address bytes directly. This gives a peformance
advantage for address bus controlled chips and simplifies the
quirks in the hardware drivers.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

First step of modularizing ECC support.
- Move ECC related functionality into a seperate embedded data structure
- Get rid of the hardware dependend constants to simplify new ECC models
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

We all inherited the same error from the original NAND board driver which
got copied and changed. Fix them all at once...
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

The _board_ driver needs to be mtd->owner, and it in turn pins the
nand.ko module. Fix them all to actually do that, and fix nand.ko not to
overwrite it -- and also to check that the caller sets it, if the caller
is a module.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

It was just too painful to deal with.
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>

Correct the MTD NAND partition size for Poodle (Sharp Zaurus SL-5600)
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

The Sharp Zaurus akita and borzoi models are large page flash devices.
This patch adds support for them to the sharpsl MTD NAND driver but
keeps the oob layout and bad block positions compatible with the Sharp
Zaurus 2.4 kernel and ROM bootloader.
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Add partition definitions for the new Sharp Zaurus models Spitz (SL-C3000),
Akita (SL-C1000) and Borzoi (SL-C3100)
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NDavid Woodhouse <dwmw2@infradead.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Correct Poodle default partition size
Signed-off-by: NRichard Purdie <rpurdie@rpsys.net>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!