Common resource and platform device structures are moved to common.c
and only the partition table and chip delay remains a per board
parameter.
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NErik Benada <erikbenada@yahoo.ca>

[ nico: fix locking, additional cleanups ]
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NNicolas Pitre <nico@marvell.com>

Just like commit 1419468a, let's save some TLB entries by making
ioremap() return pointers into the boot-time Kirkwood peripheral
iotable mapping whenever someone tries to ioremap any part of the Kirkwood
peripheral register space.
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NSiddarth Gore <gores@marvell.com>
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>

Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>

With a TCLK = 200MHz, the half period of the hardware timer is roughly
10 seconds. Because cnt32_to_63() must be called at least once per
half period of the base hardware counter, it is a bit risky to rely
solely on scheduling to generate frequent enough calls. Let's use a
kernel timer to ensure this.
Signed-off-by: NNicolas Pitre <nico@marvell.com>

sched_clock implementation for orion platform. Its realized using
free-running clocksource timer, which provides a resolution of 7.5ns
(depending on tclk). It's derived from PXA's sched_clock implementation.

[ nico: renamed orion2ns to tclk2ns, fixed max value in the comment ]
Signed-off-by: NStefan Agner <stefan.agner@yahoo.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

The patch adds support for Kirkwood cpu idle.
Two idle states are defined:
1. Wait-for-interrupt (replacing default kirkwood wfi)
2. Wait-for-interrupt and DDR self refresh
Signed-off-by: NRabeeh Khoury <rabeeh@marvell.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Add hook so that the HW RNG source on the TS-78xx is available.
Signed-off-by: NAlexander Clouter <alex@digriz.org.uk>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

The flat loader uses an architecture's flat_stack_align() to align the
stack but assumes word-alignment is enough for the data sections.

However, on the Xtensa S6000 we have registers up to 128bit width
which can be used from userspace and therefor need userspace stack and
data-section alignment of at least this size.

This patch drops flat_stack_align() and uses the same alignment that
is required for slab caches, ARCH_SLAB_MINALIGN, or wordsize if it's
not defined by the architecture.

It also fixes m32r which was obviously kaput, aligning an
uninitialized stack entry instead of the stack pointer.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: NOskar Schirmer <os@emlix.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Bryan Wu <cooloney@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NPaul Mundt <lethal@linux-sh.org>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: NJohannes Weiner <jw@emlix.com>
Acked-by: NMike Frysinger <vapier.adi@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Add cmpxchg/cmpxchg64 support for ARMv6K and ARMv7 systems
(original patch from Catalin Marinas <catalin.marinas@arm.com>)

The cmpxchg and cmpxchg64 functions can be implemented using the
LDREX*/STREX* instructions. Since operand lengths other than 32bit are
required, the full implementations are only available if the ARMv6K
extensions are present (for the LDREXB, LDREXH and LDREXD instructions).

For ARMv6, only 32-bits cmpxchg is available.

Mathieu :

Make cmpxchg_local always available with best implementation for all type sizes (1, 2, 4 bytes).
Make cmpxchg64_local always available.

Use "Ir" constraint for "old" operand, like atomic.h atomic_cmpxchg does.

Change since v3 :
- Add "memory" clobbers (thanks to Nicolas Pitre)
- removed __asmeq(), only needed for old compilers, very unlikely on ARMv6+.

Note : ARMv7-M should eventually be ifdefed-out of cmpxchg64. But it's not
supported by the Linux kernel currently.

Put back arm < v6 cmpxchg support.
Signed-off-by: NMathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
CC: Catalin Marinas <catalin.marinas@arm.com>
CC: Nicolas Pitre <nico@cam.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Mathieu Desnoyers pointed out that the ARM barriers were lacking:

- cmpxchg, xchg and atomic add return need memory barriers on
  architectures which can reorder the relative order in which memory
  read/writes can be seen between CPUs, which seems to include recent
  ARM architectures. Those barriers are currently missing on ARM.

- test_and_xxx_bit were missing SMP barriers.

So put these barriers in.  Provide separate atomic_add/atomic_sub
operations which do not require barriers.
Reported-Reviewed-and-Acked-by: NMathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Signed-off-by: NPaulius Zaleckas <paulius.zaleckas@teltonika.lt>

Our signal syscall restart handling for these kernels still uses
the userspace stack to build code for restarting the syscall.
Unfortunately, fixing this is non-trivial, and so for the time
being, we resolve the problem by disabling NX support.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Since commit eb0519b5, mv643xx_eth is non functional on ARM because
the platform device declaration does not include any coherent DMA mask
and coherent memory allocations fail.
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Signed-off-by: NMarek Vasut <marek.vasut@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

This patch modifies parameter of clksrc_read() from 'void' to
'struct clocksource *cs', which fixes compile warning for
incompatible parameter type.
Signed-off-by: NColy Li <coly.li@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NMingwei Wang <mwwang@marvell.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Remove explicit names from platform device resources since they will
automatically be named after the platform device they're associated
with.
Signed-off-by: NMartin Michlmayr <tbm@cyrius.com>
Acked-by: NRussell King <linux@arm.linux.org.uk>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

For the QNAP TS-119 and TS-219 the wrong MPPs were used for the SATA
activity/presence LEDs. The new settings make these LEDs work as
expected.
Signed-off-by: NThomas Reitmayr <treitmayr@devbase.at>
Tested-by: NMartin Michlmayr <tbm@cyrius.com>
Signed-off-by: NNicolas Pitre <nico@marvell.com>

Fix LPM configuration on ezx.c
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Remove the __initdata annotation for the clock lookups, since they
will be needed when loading modules which use clk_get().
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Remove the __initdata annotation for the clock lookups, since they
will be needed when loading modules which use clk_get().
Signed-off-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Currently spitz_ohci_init() that requests GPIO doesn't have
corresponding spitz_ohci_exit() which will gpio_free(). This causes
minor problems e.g. during resume when the OHCI device can't be resumed.
Signed-off-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

'mach-pxa' platforms currently rely on a bootloader to setup GPIO pins
and clear RDH (to enable inputs).

A kernel loaded by a 'minimal' bootloader, that doesn't touch any pins,
will not function correctly; inputs will remain disabled, even after the
pins are configured. The following change fixes the issue and has been
verified on Gumstix Verdex XL6P and a custom PXA270 platform.
Signed-off-by: NTimothy Clacy <tcl@phaseone.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

I want to reuse tosa/spitz gpio_reset code, but my board needs the reset
gpio to be driven high during normal operation.
Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Acked-by: NDmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NDaniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: NEric Miao <eric.miao@marvell.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

pfn_valid() is meant to be able to tell if a given PFN has valid memmap
associated with it or not. In FLATMEM, it is expected that holes always
have valid memmap as long as there is valid PFNs either side of the hole.
In SPARSEMEM, it is assumed that a valid section has a memmap for the
entire section.

However, ARM and maybe other embedded architectures in the future free
memmap backing holes to save memory on the assumption the memmap is never
used. The page_zone linkages are then broken even though pfn_valid()
returns true. A walker of the full memmap must then do this additional
check to ensure the memmap they are looking at is sane by making sure the
zone and PFN linkages are still valid. This is expensive, but walkers of
the full memmap are extremely rare.

This was caught before for FLATMEM and hacked around but it hits again for
SPARSEMEM because the page_zone linkages can look ok where the PFN linkages
are totally screwed. This looks like a hatchet job but the reality is that
any clean solution would end up consumning all the memory saved by punching
these unexpected holes in the memmap. For example, we tried marking the
memmap within the section invalid but the section size exceeds the size of
the hole in most cases so pfn_valid() starts returning false where valid
memmap exists. Shrinking the size of the section would increase memory
consumption offsetting the gains.

This patch identifies when an architecture is punching unexpected holes
in the memmap that the memory model cannot automatically detect and sets
ARCH_HAS_HOLES_MEMORYMODEL. At the moment, this is restricted to EP93xx
which is the model sub-architecture this has been reported on but may expand
later. When set, walkers of the full memmap must call memmap_valid_within()
for each PFN and passing in what it expects the page and zone to be for
that PFN. If it finds the linkages to be broken, it assumes the memmap is
invalid for that PFN.
Signed-off-by: NMel Gorman <mel@csn.ul.ie>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Having discussed broadcast tick support with Thomas Glexiner, the
broadcast tick devices should be registered with a higher rating
than the global tick device, and it should have the ONESHOT and
PERIODIC feature flags set.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NThomas Glexiner <tglx@linutronix.de>

smp_cross_call_done() is a no-op for MPCore, and since it's only
used by platform code, there's no point in having it unless it's
doing something.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The ARM SMP code wasn't properly updated for the cpumask changes, which
results in smp_timer_broadcast() broadcasting ticks to non-online CPUs.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Compilation for this board yields the following errors:

arch/arm/mach-pxa/viper.c:511: error: 'FFUART' undeclared here (not in a function)
arch/arm/mach-pxa/viper.c:520: error: 'BTUART' undeclared here (not in a function)
arch/arm/mach-pxa/viper.c:529: error: 'STUART' undeclared here (not in a function)

Fix them by including the necessary header.
Signed-off-by: NRicardo Martins <rasm@fe.up.pt>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Fix the clkdev API support for the ep93xx uart clocks.

The uarts available in the ep93xx have individual clock controls.
The current implementation assumes that the bootloader has enabled
the clocks before the kernel has booted. It also assumes that the
bootloader has set the UARTBAUD bit indicating that the uarts are
running off the 14.7456MHz external crystal.

This fixes both issues. It also allows the uart clocks to be stopped
when there are no users.
Tested-by: NMatthias Kaehlcke <matthias@kaehlcke.net>

Cc: Ryan Mallon <ryan@bluewatersys.com>
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This makes the framebuffer work on omap3.

Also fix the clk_get usage for checkpatch.pl
"ERROR: do not use assignment in if condition".

Cc: Imre Deak <imre.deak@nokia.com>
Cc: linux-fbdev-devel@lists.sourceforge.net
Acked-by: NKrzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The OMAP3430ES2_SAVEANDRESTORE_SHIFT macro is used
by powerdomain code in
"1 << OMAP3430ES2_SAVEANDRESTORE_SHIFT" manner, but
the definition was also (1 << 4), meaning we actually
modified bit 16. So the definition needs to be 4.

This fixes also a cold reset HW bug in OMAP3430 ES3.x
where some of the efuse bits are not isolated during
wake-up from off mode. This can cause randomish
cold resets with off mode. Enabling the USBTLL hardware
SAVEANDRESTORE causes the core power up assert to be
delayed in a way that we will not get faulty values
when boot ROM is reading the unisolated registers.
Signed-off-by: NKalle Jokiniemi <kalle.jokiniemi@digia.com>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Acked-by: NPaul Walmsley <paul@pwsan.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

As per 3430 TRM, there are 6 banks [0 to 191]
Signed-off-by: NTom Rix <Tom.Rix@windriver.com>
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The s3c24xx_register_clock() function has been doing a test
on clk->owner to see if it is NULL, and then setting itself
as the owner if clk->owner == NULL.

This is not needed, arch/arm/plat-s3c/clock.c cannot be
compiled as a module, and even if it was, it should not be
playing with this field if it being registered from somewhere
else.

The best course of action is to remove this bit of
code completely.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>