This patch adds LFPS filter quirk, and some special platforms can configure
that if it is needed.

[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds delay PHY power change from P0 to P1/P2/P3 when link state
changing from U0 to U1/U2/U3 respectively, and some special platforms can
configure that if it is needed.

[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds delay P0 to P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.

[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds request P1/P2/P3 quirk for U2/U2/U3, and some special
platforms can configure that if it is needed.

[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds P3 in U2 SS inactive quirk, and some special platforms can
configure that if it is needed.

[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds u2exit lfps quirk, and some special platforms can configure
that if it is needed.

[ balbi@ti.com : added DeviceTree binding documentation ]
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When parameter DWC_USB3_LPM_ERRATA_ENABLE is enabled in Andvanced
Configuration of coreConsultant, it supports of xHCI BESL Errata Dated
10/19/2011 is enabled in host mode. In device mode it adds the capability
to send NYET response threshold based on the BESL value received in the LPM
token, and the threhold is configurable for each soc platform.

This patch adds an entry that soc platform is able to define the lpm
capacity with their own device tree or bus glue layer.

[ balbi@ti.com : added devicetree documentation, spelled threshold
		completely, made sure threshold is only applied to
		proper core revisions. ]
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adds disscramble quirk, and it only needs to be enabled at fpga
board on some vendor platforms.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some chip vendor is on pre-silicon phase, which needs to use the simulation
board. It should have the same product and vendor id with the true soc, but
might have some minor different configurations.

Below thread discussion proposes to find a method to distinguish between
simulation board and soc.

http://marc.info/?l=linux-usb&m=141194772206369&w=2

In Andvanced Configuration of coreConsultant, there is the parameter of
DWC_USB_EN_FPGA. This bit has the function we need. And it would response as 7
bit of GHWPARAMS6 register. So it's able to check this functional bit to confirm
if works on FPGA board.
Reported-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Using ->prepare()/->complete() to mask/unmask
IRQs is wrong at least for dwc3. We need to
make sure that by the end of ->resume(), IRQs
are working and ready to fire because a child
device may need working IRQs for its own ->resume()
method.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When we're debugging hard-to-reproduce and time-sensitive
use cases, printk() poses too much overhead. That's when
the kernel's tracing infrastructure comes into play.

This patch implements a few initial tracepoints for the
dwc3 driver. More traces can be added as necessary in order
to ease the task of debugging dwc3.
Reviewed-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

No functional changes, just making sure we're dealing
with unsigned ints.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Newer DWC3 controllers can be built for USB 2.0-only mode, where
most of the USB 3.0 circuitry is left out. To support this mode,
the driver must limit the speed programmed into the DCFG register
to Hi-Speed or lower.

Reads and writes to the PIPECTL register are left as-is, since
they should be no-ops in USB 2.0-only mode. Calls to phy_init()
etc. for the USB3 phy are also left as-is, since the no-op USB3
phy should be used for USB 2.0-only mode controllers.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Adapted dwc3 core to use the Generic PHY Framework. So for init, exit,
power_on and power_off the following APIs are used phy_init(), phy_exit(),
phy_power_on() and phy_power_off().

However using the old USB phy library wont be removed till the PHYs of all
other SoC's using dwc3 core is adapted to the Generic PHY Framework.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

few new revisions of the core have been released,
add them to our list of revisions so we can apply
workarounds if necessary.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

commit 388e5c51 (usb: dwc3: remove dwc3 dependency
on host AND gadget.) created the possibility for
host-only and peripheral-only dwc3 builds but
left a possible randconfig build error when host-only
builds are selected.

Cc: <stable@vger.kernel.org> # v3.8+
Reported-by: NJim Davis <jim.epost@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

no functional changes, just converting spaces
into tab.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We must read HWPARAMS4 register to figure out
how many scratch buffers we should allocate.

Later patch will use "Set Scratchpad Buffer
Array" command to pass the pointer to the
IP so it can be used during hibernation.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This extra field will save endpoint state when we're
about to enter hibernation. It will be used later
to restore the endpoint state when resuming.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this will tell driver that this version
of the core was configured with hibernation
feature enabled.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

move 1-bit flags to the bottom of the structure,
sort all bit flags alphabetically, add documentation
which was missing.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This bit is necessary for implemeting workaround
for known issue with some revisions of this core.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Around DWC USB3 2.30a release another bit has been added to the
Device-Specific Event (DEVT) Event Information (EvtInfo) bitfield.

Because of that, what used to be 8 bits long, has become 9 bits long.

Per dwc3 2.30a+ spec in the Device-Specific Event (DEVT), the field of
Event Information Bits(EvtInfo) uses [24:16] bits, and it has 9 bits
not 8 bits. And the following reserved field uses [31:25] bits not
[31:24] bits, and it has 7 bits.

So in dwc3_event_devt, the bit mask should be:
event_info	[24:16]		9 bits
reserved31_25	[31:25]		7 bits

This patch makes sure that newer core releases will work fine with
Linux and that we will decode the event information properly on new
core releases.

[ balbi@ti.com : improve commit log a bit ]

Cc: <stable@vger.kernel.org>
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Change intervall into interval.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

That register has more than just the event buffer
size; we can also mask and unmask that particular
interrupter on bit 31 of that register.

In this patch we introduce the necessary macros
and make sure to use the new macros while also
making sure we mask interrupts during driver
removal.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

the macro DWC3_DCFG_LPM_CAP was defined twice.

This patch just removes one of the definitions,
no functional changes.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch adapts the dwc3 to use the device tree helper
"of_usb_get_dr_mode" for the mode of operation of the dwc3 instance
being probed.

[ balbi@ti.com : make of_usb_get_dr_mode() conditional on
	dev->of_node and let pdata pass dr_mode too ]
Reviewed-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NRuchika Kharwar <ruchika@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This is a Linux-only driver which makes use
of GPL-only symbols. It makes no sense to
maintain Dual BSD/GPL licensing for this driver.

Considering that the amount of work to use this
driver in any different operating system would likely
be as large as developing the driver from scratch and
considering that we depend on GPL-only symbols, we
will switch over to a GPL v2-only license.

Cc: Anton Tikhomirov <av.tikhomirov@samsung.com>
Acked-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

@list is not as a parameter of dwc3_event_buffer, so remove it in
comments.
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Per dwc3 2.50a spec, the is_devspec bit is used to distinguish the
Device Endpoint-Specific Event or Device-Specific Event (DEVT). If the
bit is 1, the event is represented Device-Specific Event, then use
[7:1] bits as Device Specific Event to marked the type. It has 7 bits,
and we can see the reserved8_31 variable name which means from 8 to 31
bits marked reserved, actually there are 24 bits not 25 bits between
that. And 1 + 7 + 24 = 32, the event size is 4 byes.

So in dwc3_event_type, the bit mask should be:
is_devspec	[0]		1  bit
type		[7:1]		7  bits
reserved8_31	[31:8]		24 bits

This patch should be backported to kernels as old as 3.2, that contain
the commit 72246da4 "usb: Introduce
DesignWare USB3 DRD Driver".

Cc: <stable@vger.kernel.org>
Signed-off-by: NHuang Rui <ray.huang@amd.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch fixes the wrong OTG_EVT,OTG_EVTEN and OTG_STS register
offsets.

While at that, also add a missing register to debugfs regdump
utility.
Signed-off-by: NGeorge Cherian <george.cherian@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

hwparams2 holds the number of endpoints which
were selected during RTL generation, we can
use that on our driver.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some new revisions of the DWC3 core have
been released, let's add our defines to help
implementing known erratas.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We can reuse the generic implementation via
our struct usb_gadget.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

we can cache the last read value of the event
buffer count register on this field, for later
handling.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

that way we know if a particular event buffer
has pending events, or not.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

that irq field has been removed already. This
patch just removes its documentation.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add support for basic power management on
the dwc3 driver. While there is still lots
to improve for full PM support, this minimal
patch will already make sure that we survive
suspend-to-ram and suspend-to-disk without
major issues.

Cc: Vikas C Sajjan <vikas.sajjan@linaro.org>
Tested-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This will be used during resume to verify
if we should reconnect our pullups or not.
Tested-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

DWC3 controller curretly depends on USB && USB_GADGET.
Some hardware may like to use only host feature on dwc3,
or only gadget feature.

So, removing this dependency of USB_DWC3 on USB and USB_GADGET.
Adding the mode of operaiton of DWC3 also here
HOST/GADGET/DUAL_ROLE based on which features are enabled.

[ balbi@ti.com :
	. make sure we have default modes for all possible Kernel
		configurations.
	. Remove the config -> menuconfig change as it's unnecessary
	. switch over to IS_ENABLED() ]

CC: Doug Anderson <dianders@chromium.org>
Signed-off-by: NVivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>