drm modes are objects with indentifiers.  Make sure to preserve
the mode id when copying mode params.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

With the adjust table introduction, we need to fill out index
before getting the table version.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reverts commit 49c458e5. It
seems to have some side effects in the non-kms cases.
Signed-off-by: NDave Airlie <airlied@redhat.com>

In case the system has bad native mode info but
valid edid.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reduces the number of mode format conversions needed
and makes native panel mode support cleaner.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

- clean up tv timing handling
- unify SetCRTC_Timing and SetCRTC_UsingDTDTiming
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

DCE3+ has an AdjustDisplayPll that will adjust the pixel
clock accordingly based on the encoder/transmitter to
handle special hw requirements.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Based on recommendation from bios docs.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If the panel data is bogus this can lead to problems
later when the hardware trys to set the mode.  If the
data is invalid, report LVDS as disconnected.

Should fix fdo bug 24247.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

While investigating the cause of CRTC FIFO underruns, I noticed that when
converting the memory bandwidth calculation from the userspace X driver code,
an instance of '8.0' was apparently accidentally converted to '80'.
Signed-off-by: NMichel Dänzer <daenzer@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The hook may change the number of bytes per pixel being scanned out, which
affects the CRTC memory bandwidth requirements. E.g. booting in 8bpp and then
running X in 32bpp would result in the bandwidth requirements being
underestimated for the latter and consequently in CRTC FIFO underruns causing
visible artifacts with 3D intensive workloads.

ATOM changes only compile-tested.
Signed-off-by: NMichel Dänzer <daenzer@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The fb binding might be happening in a subsequent crtc setup call.

gets rid of some lut issues.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Both r100/r600 had this wrong, use the macro to extract the register
to relocate.
Signed-off-by: NDave Airlie <airlied@redhat.com>

There is no need to assign vb before you know that space is available.

[agd5f: adapted for kernel tree.]
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This is just a cleanup of the list macro usage.
Signed-off-by: NDave Airlie <airlied@redhat.com>

For AGP to work unmapped access must cover VRAM & AGP as
AGP is treated like VRAM by the GPU (ie physical address).
This patch properly setup the virtual memory system aperture
to cover AGP if AGP is enabled. It seems that there is memory
corruption after resume when using AGP (RV770 seems unaffected
thought). Version 2 just fix merge issue with updated AGP
fallback patch.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

When GPU acceleration is not working with AGP try to fallback to non
AGP GART (either PCI or PCIE GART). This should make KMS failure on
AGP less painfull. We still need to find out what is wrong when AGP
fails but at least user have a lot of more chances to get a working
configuration with acceleration. This patch also cleanup R600/RV770
fallback path so they use same code as others asics. Version 2
factorize agp disabling logic to avoid code duplication and bugs.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Bad generated header file leaded to use wrong register
to check IRQ status and acknowledge them. Fix the header
and use proper registers.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Duplicate bits set
Signed-off-by: NRoel Kluin <roel.kluin@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

the global refcount wasn't being increased after the first reference.
this caused an oops on unload on a multi-gpu card.
Signed-off-by: NDave Airlie <airlied@redhat.com>

The previous patches had some unwanted side effects, I've fixed
the lack of 32bpp working, and fixed up 16bpp so it should also work.

this also adds the interface to allow the driver to set a preferred
console depth so for example low memory rn50 can set it to 8bpp.
It also catches 24bpp on cards that can't do it and forces 32bpp.

Tested on r100/r600/i945.
Signed-off-by: NDave Airlie <airlied@redhat.com>

This adds support for the setcmap api and fixes the 8bpp
support at least on radeon hardware. It adds a new load_lut
hook which can be called once the color map is setup.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Also add single crtc for RN50 chips.

changes in v2:
fix vblank init to respect single crtc flag
fix r100 mode bandwidth to respect single crtc flag
Signed-off-by: NDave Airlie <airlied@redhat.com>

We can get the corresponding info by adding the boot option of "drm.debug=
0x07". But On some boxes it will print the following message many times in
course of moving mouse. In such case the useful DRM debug info will be flushed.
   >[drm:drm_mode_cursor_ioctl],

Avoid using the DRM_DEBUG_KMS in drm_mode_cursor_ioctl.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

"Surround View" is an option in the system bios that
enables the AMD IGP chip in conjunction with a
discrete AMD card.  However, since the IGP vbios is
part of the system bios it is not accessible via the
rom bar or the legacy vga location.  When "Surround View"
is enabled in the system bios, the system bios puts a
copy of the IGP vbios image at the start of vram.

This patch adds support for reading the vbios image out
of vram on IGP cards.
Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Avivo hw have vblank interrupt in different place, fixes
irq handling (especialy irq disabling while suspending or
shuting down the module).
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

R600 & RV770 family are all using atombios so remove dead code and
print an error message if we fail to find a valid atombios.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

When acceleration doesn't work we should free associated memory
and stop GPU block responsible for hardware acceleration so we
don't waste resource or let think one component of the driver that
a GPU feature is working/running while it doesn't actualy work.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We were calling reset unconditionaly in the startup path
this is bad we need to call GPU reset for a good reason
as after reset the GPU is in unknown states. To avoid any
more bad things to happen we now also unconditionaly
reinitialize the GPU after reset. This patch fix few issues
reported by different people regarding KMS & R6XX/RV7XX hw.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This split write back buffer handling into 3 functions,
wb_fini for cleanup, wb_enable/wb_disable for enabling/disabling
write back used for suspend/resume. This should fix
potential issue of letting the write back active before
suspending. We need to allocate memory in wb_enable because
we can only allocate once GART is running.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This remove old init path and allow code cleanup, now all hw
use the new init path, see top of radeon.h for description of
this.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

New init path allow to simply asic initialization and make easier
to trace what happen on each different asic. We are removing most
callback. Do a massive RS600 register cleanup to clarify RS600
register, we are still bit fuzy on some register and waiting for
more informations. I don't have hw to test, so this patch is a
best effort to not break anythings and to try to improve things.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Also cleanup register specific to RS690/RS740. Version 2 add
missing header file for register, remove unecessary call to AGP
function and fix an indentation bug.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

New init path allow to simply asic initialization and make easier
to trace what happen on each different asic. We are removing most
callback. More cleanup should happen latter to remove even more
callback. Also cleanup register specific to R100,RV200,RV250.
Version 2 correct the placement on IGP of the VRAM inside GPU address
space to match the stollen RAM placement of IGP.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Also cleanup register specific to R300.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Also cleanup register specific to RS400/RS480. This patch also fix
legacy VGA register used to disable VGA access we were programming
wrong register. Now we should properly disable VGA on r100 up to
rs400 asics. Note that RS400/RS480 resume is broken, it hangs the
computer while reprogramming dynamic clock, doesn't work either
without that patch. We need to spend more time investigating this
issue. Version 2 of the patch remove dead code that was left
commented out in the previous version. Version 3 correct the
placement on IGP of the VRAM inside GPU address space to match the
stollen RAM placement of IGP.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Convert the r520 asic support to new init path, change are smaller than
previous one as most of the architecture is now in place and more code
sharing can happen btw various asics.
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Convert the rv515 asic support to new init path also add an explanation
in radeon.h about the new init path. There is also few cleanups
associated with this change (others asic calling rv515 helper
functions).
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Compiling the radeon DRM driver with !CONFIG_DEBUG_FS
throws the following warnings:

drivers/gpu/drm/radeon/radeon_ttm.c: In function 'radeon_ttm_debugfs_init':
drivers/gpu/drm/radeon/radeon_ttm.c:714: warning: unused variable 'i'
drivers/gpu/drm/radeon/radeon_ttm.c: At top level:
drivers/gpu/drm/radeon/radeon_ttm.c:692: warning: 'radeon_mem_types_list' defined but not used
drivers/gpu/drm/radeon/radeon_ttm.c:693: warning: 'radeon_mem_types_names' defined but not used

Fix: move these variables inside the #if defined(CONFIG_DEBUG_FS)
block in radeon_ttm_debugsfs_init(), which is the only place using them.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NDave Airlie <airlied@linux.ie>

Compiling DRM throws the following warning if MAGIC_SYSRQ is disabled:

drivers/gpu/drm/drm_fb_helper.c:101: warning: 'sysrq_drm_fb_helper_restore_op' defined but not used

Fix: place sysrq_drm_fb_helper_restore_op and associated
definitions inside #ifdef CONFIG_MAGIC_SYSRQ.
Signed-off-by: NMikael Pettersson <mikpe@it.uu.se>
Signed-off-by: NDave Airlie <airlied@linux.ie>