The check for the TRDY flag after writing the character is not needed.
Also do a cpu_relax() inside the loop.

Pass a struct uart_port to altera_uart_console_putc, so we do not need
to get it (and dereference pointers) for every character.

Cc: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Don't take the port spinlock in uart functions where the serial core
already takes care of locking/unlocking them.

The code would actually lock up on architectures where spinlocks are
implemented (not the case on nios2 where this driver is primarily used
for now, thus this bug didn't trigger).

Also protect calling altera_uart_rx_chars/altera_uart_tx_chars in the
interrupt handler by the port spinlock.

Thanks to Ian Abbott for pointing these issues out.

Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: NTobias Klauser <tklauser@distanz.ch>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

In gsm_dlci_data_kick() we call gsm_dlci_data_sweep() with the
"gsm->tx_lock" held so we can't lock it again inside
gsm_dlci_data_sweep().  I removed that lock from and added one to
gsmld_write_wakeup() instead.  The sweep function is only called from
those two places.
Signed-off-by: NDan Carpenter <error27@gmail.com>
Acked-by: NAlan Cox <alan@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This most likely won't cause problems on systems as people don't typically
enable GPIO RTS/CTS if they don't actually use it.
Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Anomaly 05000230 (over sampling of the UART STOP bit) applies only when
the peripheral is operating in UART mode.  So drop the anomaly handling
when the UART is in IRDA mode.
Signed-off-by: NGraf Yang <graf.yang@analog.com>
Signed-off-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAlexander Kurz <linux@kbdbabel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Set the mnd counter based on uartclk. This fixes a problem
on 7x30 where the uartclk is 19.2Mhz rather than the usual
4.8Mhz.

Trout incorrectly reports uartclk to be running at 19.2Mhz
It is actually running at 4.8Mhz.  For trout force mnd
counter values as if uartclk was fed by tcxo/4.
Signed-off-by: NAbhijeet Dharmapurikar <adharmap@codeaurora.org>
[dwalker@codeaurora.org: inlined, moved into header, added comments.]
Signed-off-by: NDaniel Walker <dwalker@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: implement on-demand HPA unlocking
  libata: use the enlarged capacity after late HPA unlock
  SCSI: implement sd_unlock_native_capacity()
  libata-sff: trivial corrections to Kconfig help text
  sata_nv: don't diddle with nIEN on mcp55
  sata_via: magic vt6421 fix for transmission problems w/ WD drives

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched, trace: Fix sched_switch() prev_state argument
  sched: Fix wake_affine() vs RT tasks
  sched: Make sure timers have migrated before killing the migration_thread

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, smpboot: Fix cores per node printing on boot
  x86/amd-iommu: Fall back to GART if initialization fails
  x86/amd-iommu: Fix crash when request_mem_region fails
  x86/mm: Remove unused DBG() macro
  arch/x86/kernel: Add missing spin_unlock

* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
  powerpc/macio: Fix probing of macio devices by using the right of match table
  agp/uninorth: Fix oops caused by flushing too much
  powerpc/pasemi: Update MAINTAINERS file
  powerpc/cell: Fix integer constant warning
  powerpc/kprobes: Remove resume_execution() in kprobes
  powerpc/macio: Don't dereference pointer before null check

* 'for-linus/bugfixes' of git://xenbits.xensource.com/people/ianc/linux-2.6:
  xen: avoid allocation causing potential swap activity on the resume path
  xen: ensure timer tick is resumed even on CPU driving the resume

Merge branch 'perf-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'perf-fixes-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf: Fix crash in swevents
  perf buildid-list: Fix --with-hits event processing
  perf scripts python: Give field dict to unhandled callback
  perf hist: fix objdump output parsing
  perf-record: Check correct pid when forking
  perf: Do the comm inheritance per thread in event__process_task
  perf: Use event__process_task from perf sched
  perf: Process comm events by tid
  blktrace: Fix new kernel-doc warnings
  perf_events: Fix unincremented buffer base on partial copy
  perf_events: Fix event scheduling issues introduced by transactional API
  perf_events, trace: Fix perf_trace_destroy(), mutex went missing
  perf_events, trace: Fix probe unregister race
  perf_events: Fix races in group composition
  perf_events: Fix races and clean up perf_event and perf_mmap_data interaction

* 'virtio' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
  virtio: console: Fix crash when port is unplugged and blocked for write
  virtio: console: Fix crash when hot-unplugging a port and read is blocked
  virtio-blk: fix minimum number of S/G elements

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c: Remove all i2c_set_clientdata(client, NULL) in drivers
  i2c/busses: Move two drivers to embedded section
  i2c: Rename i2c_check_addr to i2c_check_addr_busy
  i2c: Document reserved I2C addresses
  i2c: Check for address validity on client registration
  i2c: Share the I2C device presence detection code
  Documentation/i2c: Checkpatch cleanup

* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
  crypto: crypto4xx - Fix build breakage
  n2_crypto: Plumb fallback ahash requests properly.
  n2_crypto: Fix MAU kmem_cache name.
  n2_crypto: Fix build after of_device/of_platform_driver changes.

Frederic reported that because swevents handling doesn't disable IRQs
anymore, we can get a recursion of perf_adjust_period(), once from
overflow handling and once from the tick.

If both call ->disable, we get a double hlist_del_rcu() and trigger
a LIST_POISON2 dereference.

Since we don't actually need to stop/start a swevent to re-programm
the hardware (lack of hardware to program), simply nop out these
callbacks for the swevent pmu.
Reported-by: NFrederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: NPeter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1275557609.27810.35218.camel@twins>
Signed-off-by: NIngo Molnar <mingo@elte.hu>

* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
  cifs: fix page refcount leak

* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (41 commits)
  drm/radeon/kms: make sure display hw is disabled when suspending
  drm/vmwgfx: Allow userspace to change default layout. Bump minor.
  drm/vmwgfx: Fix framebuffer modesetting
  drm/vmwgfx: Fix vga save / restore with display topology.
  vgaarb: use MIT license
  vgaarb: convert pr_devel() to pr_debug()
  drm: fix typos in Linux DRM Developer's Guide
  drm/radeon/kms/pm: voltage fixes
  drm/radeon/kms/pm: radeon_set_power_state fixes
  drm/radeon/kms/pm: patch default power state with default clocks/voltages on r6xx+
  drm/radeon/kms/pm: enable SetVoltage on r7xx/evergreen
  drm/radeon/kms/pm: add support for SetVoltage cmd table (V2)
  drm/radeon/kms/evergreen: add initial CS parser
  drm/kms: disable/enable poll around switcheroo on/off
  drm/nouveau: fixup confusion over which handle the DSM is hanging off.
  drm/nouveau: attempt to get bios from ACPI v3
  drm/nv50: cast IGP memory location to u64 before shifting
  drm/ttm: Fix ttm_page_alloc.c
  drm/ttm: Fix cached TTM page allocation.
  drm/vmwgfx: Remove some leftover debug messages.
  ...

* 'merge' of git://git.secretlab.ca/git/linux-2.6:
  of/powerpc: fix fsl_msi device node pointer
  of/watchdog: gef_wdt.c: fix build breakage
  of/edac: fix build breakage in drivers
  of/net: fs_enet/mii-bitbang.c: fix build breakage
  of/usb: fsl_qe_udc.c: fix build breakage
  of/crypto: crypto4xx_core.c: fix build breakage
  of/dma: fix build breakage in ppc4xx adma driver
  of/mtd: nand: fix build breakage in drivers
  of/video: fix build breakage in FB drivers
  of/pcmcia: m8xx_pcmcia.c: Fix build failures
  of/rtc: rtc-mpc5121.c: Fix build failures
  of/dma: mpc512x_dma.c: Fix build failures
  of/mtd/nand: mpc5121_nfc.c: Fix build failures
  of/spi: mpc512x_psc_spi.c: Fix build failures
  watchdog: Fix build failure with OF changes
  of/spi: Fix build failure on spi_ppc4xx.c
  of/usb: fix build error due to of_node pointer move
  of/powerpc: fix 85xx RapidIO device node pointer

When a program that has a virtio port opened and blocked for a write
operation, a port hot-unplug event will later led to a crash when
SIGTERM was sent to the program. Fix that.
Signed-off-by: NAmit Shah <amit.shah@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

When removing a port we don't check if a program was blocked for read.
This leads to a crash when SIGTERM is sent to the program after
hot-unplugging the port.
Signed-off-by: NAmit Shah <amit.shah@redhat.com>
Signed-off-by: NRusty Russell <rusty@rustcorp.com.au>

We need at least one S/G element to operate properly, as does the block
layer which increments it to one anyway.  We hit this due to a qemu
bug which advertises a sg_elements of 0 under some circumstances.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (tweaked logic)

I2C drivers can use the clientdata-pointer to point to private data. As I2C
devices are not really unregistered, but merely detached from their driver, it
used to be the drivers obligation to clear this pointer during remove() or a
failed probe(). As a couple of drivers forgot to do this, it was agreed that it
was cleaner if the i2c-core does this clearance when appropriate, as there is
no guarantee for the lifetime of the clientdata-pointer after remove() anyhow.
This feature was added to the core with commit
e4a7b9b0 to fix the faulty drivers.

As there is no need anymore to clear the clientdata-pointer, remove all current
occurrences in the drivers to simplify the code and prevent confusion.
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NRichard Purdie <rpurdie@linux.intel.com>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

And fix a typo while we are here
Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Otherwise it's not clear what it is checking.

Also move the function to save a forward declaration.
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Move strict I2C address validity check to a single function, and
document the reserved I2C addresses there.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Hans Verkuil <hverkuil@xs4all.nl>

Do basic address validity checks when a client is being registered. We
already had checks in place for devices which are being detected, but
not for devices which are simply instantiated.

This is a very basic check. We don't want to do strict checking here
because some devices are known to infringe the I2C address constraints
(e.g. IR receivers at 7-bit address 0x7a while this value is
supposedly reserved for 10-bit addresses.) So we assume the caller
knows what it is doing.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Matthieu Castet <castet.matthieu@free.fr>

Use the same I2C device presence detection code for legacy and new
device detection functions. This is more consistent and makes the code
smaller.
Signed-off-by: NJean Delvare <khali@linux-fr.org>
Cc: Matthieu Castet <castet.matthieu@free.fr>

Remove all trailing whitespace in Documentation/i2c.
Signed-off-by: NAndrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: NJean Delvare <khali@linux-fr.org>

Since the device we are resuming could be the device containing the
swap device we should ensure that the allocation cannot cause
IO.

On resume, this path is triggered when the running system tries to
continue using its devices.  If it cannot then the resume will fail;
to try to avoid this we let it dip into the emergency pools.

The majority of these changes were made when linux-2.6.18-xen.hg
changeset e8b49cfbdac0 was ported upstream in
a144ff09 but somehow this hunk was
dropped.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Acked-by: NJeremy Fitzhardinge <jeremy@goop.org>
Cc: Stable Kernel <stable@kernel.org> # .32.x

The core suspend/resume code is run from stop_machine on CPU0 but
parts of the suspend/resume machinery (including xen_arch_resume) are
run on whichever CPU happened to schedule the xenwatch kernel thread.

As part of the non-core resume code xen_arch_resume is called in order
to restart the timer tick on non-boot processors. The boot processor
itself is taken care of by core timekeeping code.

xen_arch_resume uses smp_call_function which does not call the given
function on the current processor. This means that we can end up with
one CPU not receiving timer ticks if the xenwatch thread happened to
be scheduled on CPU > 0.

Use on_each_cpu instead of smp_call_function to ensure the timer tick
is resumed everywhere.
Signed-off-by: NIan Campbell <ian.campbell@citrix.com>
Acked-by: NJeremy Fitzhardinge <jeremy@goop.org>
Cc: Stable Kernel <stable@kernel.org> # .32.x

Fixes build error caused by the OF device_node
pointer being moved into struct device
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>

Signed-off-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>

Disable the display hw when suspending.
Should fix bug:
https://bugzilla.redhat.com/show_bug.cgi?id=522393Signed-off-by: NAlex Deucher <alexdeucher@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The host may change the layout and, since the change is
communicated to the master, the master needs a way to
communicate the change to the kernel driver.

The minor version number is bumped to advertize the
availability of this feature.
Signed-off-by: NJakob Bornecrantz <jakob@vmware.com>
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Must set SVGA_NUM_REG_GUEST_DISPLAY before setting up the display information.
Signed-off-by: NJakob Bornecrantz <jakob@vmware.com>
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

vga save / restore previously didn't handle the display topology case.
Signed-off-by: NThomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Signed-off-by: NTiago Vignatti <tiago.vignatti@nokia.com>
Cc: Henry Zhao <Henry.Zhao@Sun.COM>
Signed-off-by: NDave Airlie <airlied@redhat.com>

We want to be able to use CONFIG_DYNAMIC_DEBUG in arbiter code, switch
the few existing pr_devel() calls to pr_debug().

Also, add one more debug information regarding decoding count.
Signed-off-by: NTiago Vignatti <tiago.vignatti@nokia.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>