The newly added uniphier serial port driver fails to build as
a loadable module when the base 8250 driver is built-in and
its console support enabled:

ERROR: "early_serial8250_setup" [drivers/tty/serial/8250/8250_uniphier.ko] undefined!

This changes the driver to only provide the early console support
if it is built-in itself as well.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit d56edd7e, it
shouldn't have been applied, it was fixed properly with commit
71f50c6d ("of: drop symbols declared by
_OF_DECLARE() from modules")
Reported-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The recently added uniphier 8250 port driver supports early console
probing, and it supports being built as a module, but the combination
of the two fails to link:

ERROR: "early_serial8250_setup" [drivers/tty/serial/8250/8250_uniphier.ko] undefined!

Given that earlycon support in a loadable module makes no sense,
making that code conditional on 'MODULE' is a correct solution.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Fixes: b8d20e06 ("serial: 8250_uniphier: add earlycon support")
Acked-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reuses the code of drivers/tty/serial/8250/8250_early.c except

  - Overwrite device->port.iotype and device->port.regshift for
    UPIO_MEM32 because of_setup_earlycon() has set them for UPIO_MEM.

  - Set device->baud to zero to prevent early8250_setup() from
    initializing the divisor register because port->uartclk does not
    match the frequency expected by this hardware.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NPeter Hurley <peter@hurleysoftware.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The register offset must be shifted by regshift, otherwise the
baudrate is not set.  I missed the issue probably because the
divisor register was already set by the boot loader.

Fixes: 1a8d2903 ("serial: 8250_uniphier: add UniPhier serial driver")
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

If serial8250_register_8250_port() fails, disable and unprepare the
clock before exiting.

Fixes: 1a8d2903 ("serial: 8250_uniphier: add UniPhier serial driver")
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NMatthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the driver for on-chip UART used on UniPhier SoCs.

This hardware is similar to 8250, but the register mapping is
slightly different:
  - The offset to FCR, MCR is different.
  - The divisor latch access bit does not exist.  Instead, the
    divisor latch register is available at offset 9.

This driver overrides serial_{in,out}, dl_{read,write} callbacks,
but wants to borrow most of code from 8250_core.c.
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: NMatthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>