Make sure bytesperline for Cb, Cr planes for V4L2_PIX_FMT_YUV420M
format is half of the Y plane value, rather than having same
bytesperline for all planes.
While at it, simplify the bytesperline parameter handling by
storing it when image format is set and returning those values
when getting the format, instead of recalculating bytesperline
from intermediate parameters.
Reported-by: NSebastian Dröge <sebastian.droege@collabora.co.uk>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixed wrong condition in firmware reload function used by the watchdog.
Signed-off-by: NKamil Debski <k.debski@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixes a v4l2-compliance error: setting audmode to a value other than mono
or stereo for a radio device should map to MODE_STEREO.
The spec specifies that for radio devices only mono and stereo audmodes are
valid. If the user specifies another audmode in v4l2_tuner, then that should
be mapped to valid audmode. That didn't happen here.
Note that tuner drivers might decide to limit the possible audmode even
further if it only supports mono. In that case the tuner driver can set
audmode to mono. However, that new value wasn't copied back to t->audmode,
and that has been fixed as well in this patch.
Signed-off-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds V4L2 sub-device driver for OV9650/OV9652 image sensors.
The driver exposes following V4L2 controls:
- auto/manual exposure,
- auto/manual white balance,
- auto/manual gain,
- brightness, saturation, sharpness,
- horizontal/vertical flip,
- color bar test pattern,
- banding filter (power line frequency).
Frame rate can be configured with g/s_frame_interval pad level ops.
Supported resolution are only: SXGA, VGA, QVGA.
Signed-off-by: NSylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds a v4l2 core helper function that can be used as
the log_status handler for subdevs that only need to log state
of the v4l2 controls owned by the subdev's control handler.
Signed-off-by: NSylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a v4l2 core helper function that can be used as the subdev
.subscribe_event handler. This allows to eliminate some boilerplate
from drivers that are only handling the control events.
Signed-off-by: NSylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add a v4l2 core helper function that can be used as the subdev
.unsubscribe_event handler. This allows to eliminate some
boilerplate from drivers that are only handling the control events.
Signed-off-by: NSylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch adds a helper function that allows to modify range,
i.e. minimum, maximum, step and default value of a v4l2 control,
after the control has been created and initialized. This is helpful
in situations when range of a control depends on user configurable
parameters, e.g. camera sensor absolute exposure time depending on
an output image resolution and frame rate.
v4l2_ctrl_modify_range() function allows to modify range of an
INTEGER, BOOL, MENU, INTEGER_MENU and BITMASK type controls.
Based on a patch from Hans Verkuil http://patchwork.linuxtv.org/patch/8654.
Signed-off-by: NSylwester Nawrocki <sylvester.nawrocki@gmail.com>
Acked-by: NHans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add common header file defining standard image sizes, so we can
avoid redefining those in each driver.
Signed-off-by: NSylwester Nawrocki <sylvester.nawrocki@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Instead chaneg the passed in format to the pwc default pixelformat.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Also replaced:
 #if !defined CONFIG_USB_SN9C102 && !defined CONFIG_USB_SN9C102_MODULE
with:
 #if !IS_ENABLED(CONFIG_USB_SN9C102)
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_INPUT) || \
     defined(CONFIG_INPUT_MODULE)
with:
 #if IS_ENABLED(CONFIG_INPUT)
This change was made for: CONFIG_INPUT
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

replace:
 #if defined(CONFIG_USB_SI470X) || \
     defined(CONFIG_USB_SI470X_MODULE)
with:
 #if IS_ENABLED(CONFIG_USB_SI470X)
This change was made for: CONFIG_USB_SI470X,
CONFIG_I2C_SI470X
Reported-by: NMauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This patch fixes a bug which causes all histogram regions to start in the
top left corner of the image. The histogram region coordinates are 16 bit
values which share a 32 bit register. The bug is due to the region end
value assignments overwriting the region start values with zero.
Signed-off-by: NJohannes Schellen <Johannes.Schellen@rwth-aachen.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Replace kzalloc, request_mem_region, ioremap, clk_get and regulator_get
with their devm_* managed replacement.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

kzalloc initializes the memory it allocates to 0, there's no need for an
explicit memset.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

The preview engine includes filters that consume columns and lines as
part of their operation, thus resulting in a cropped image. To allow
turning those filters on/off during streaming without affecting the
output image size, the driver adds additional cropping to make the total
number of cropped columns and lines constant regardless of which filters
are enabled.
This process needlessly includes the CFA filter, as whether the filter
is enabled only depends on the sink pad format, which can't change
during streaming.
Exclude the CFA filter from the preview engine margins.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: NSakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Ming Lei reported:
IMO, there is a minor fault in the error handling path of
uvc_status_start() inside uvc_v4l2_open(), and the 'users' count should
have been decreased before usb_autopm_put_interface(). In theory, a [URB
resubmission] warning can be triggered when the device is opened just
between usb_autopm_put_interface() and atomic_dec(&stream->dev->users).
The fix is trivial.
Reported-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Signed-off-by: NPeter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: NEzequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add the missing unlock on the error handling path in function
vpbe_initialize().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: NPrabhakar Lad <prabhakar.lad@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

drivers/media/platform/davinci/dm355_ccdc.c:593:9: warning: ‘val1’ may be
used uninitialized in this function [-Wuninitialized]
drivers/media/platform/davinci/dm355_ccdc.c:560:6: note: ‘val1’ was declared here
This is a false positive but the compiler has no way to know about it,
so initialize the variable to 0.
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NManjunath Hadli <manjunath.hadli@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NManjunath Hadli <manjunath.hadli@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NManjunath Hadli <manjunath.hadli@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I2C drivers can use devm_kzalloc() too in their .probe() methods. Doing so
simplifies their clean up paths.
Signed-off-by: NLad, Prabhakar <prabhakar.lad@ti.com>
Signed-off-by: NManjunath Hadli <manjunath.hadli@ti.com>
Acked-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Compiling the saa7164 driver without CONFIG_VIDEO_ADV_DEBUG set triggers
these GCC warnings:
    drivers/media/pci/saa7164/saa7164-encoder.c:1301:12: warning: ‘saa7164_g_register’ defined but not used [-Wunused-function]
    drivers/media/pci/saa7164/saa7164-encoder.c:1314:12: warning: ‘saa7164_s_register’ defined but not used [-Wunused-function]
Silence these warnings by wrapping these two functions in an "#ifdef
CONFIG_VIDEO_ADV_DEBUG" and "#endif" pair.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>