Skip to content

cloud-kernel
cloud-kernel

openanolis / cloud-kernel
1 年多 前同步成功

通知 160
Star 36
Fork 7
cloud-kernel
cloud-kernel
切换分支/标签
  1. 29 5月, 2011 8 次提交
  3. 28 5月, 2011 7 次提交
    • L
      mfd: Fix build breakage caused by tps65910 gpio directory move · 66c500ff
      由 Liam Girdwood 提交于 
      Signed-off-by: NLiam Girdwood <lrg@ti.com>
Acked-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
      66c500ff
    • M
      mfd: Use mfd cell platform_data for db8500-prcmu cells platform bits · 1ed7891f
      由 Mattias Wallin 提交于 
      With the addition of a device platform mfd_cell pointer, MFD drivers
can go back to passing platform data back to their sub drivers.
This allows for an mfd_cell->mfd_data removal and thus keep the
sub drivers MFD agnostic. This is mostly needed for non MFD aware
sub drivers.
Signed-off-by: NMattias Wallin <mattias.wallin@stericsson.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
      1ed7891f
    • T
      gpio/pch_gpio: Support new device ML7223 · bc786cce
      由 Tomoya MORINAGA 提交于 
      Support new device OKI SEMICONDUCTOR ML7223 IOH(Input/Output Hub).
The ML7223 IOH is for MP(Media Phone) use.
The ML7223 is companion chip for Intel Atom E6xx series.
The ML7223 is completely compatible for Intel EG20T PCH.
Signed-off-by: NTomoya MORINAGA <tomoya-linux@dsn.okisemi.com>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
      bc786cce
    • L
      gpio: make gpio_{request,free}_array gpio array parameter const · 7c295975
      由 Lars-Peter Clausen 提交于 
      gpio_{request,free}_array should not (and do not) modify the passed gpio
array, so make the parameter const.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Acked-by: NWolfram Sang <w.sang@pengutronix.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGrant Likely <grant.likely@secretlab.ca>
      7c295975
    • S
      Intel xhci: Limit number of active endpoints to 64. · 2cf95c18
      由 Sarah Sharp 提交于 
      The Panther Point chipset has an xHCI host controller that has a limit to
the number of active endpoints it can handle.  Ideally, it would signal
that it can't handle anymore endpoints by returning a Resource Error for
the Configure Endpoint command, but they don't.  Instead it needs software
to keep track of the number of active endpoints, across configure endpoint
commands, reset device commands, disable slot commands, and address device
commands.

Add a new endpoint context counter, xhci_hcd->num_active_eps, and use it
to track the number of endpoints the xHC has active.  This gets a little
tricky, because commands to change the number of active endpoints can
fail.  This patch adds a new xHCI quirk for these Intel hosts, and the new
code should not have any effect on other xHCI host controllers.

Fail a new device allocation if we don't have room for the new default
control endpoint.  Use the endpoint ring pointers to determine what
endpoints were active before a Reset Device command or a Disable Slot
command, and drop those once the command completes.

Fail a configure endpoint command if it would add too many new endpoints.
We have to be a bit over zealous here, and only count the number of new
endpoints to be added, without subtracting the number of dropped
endpoints.  That's because a second configure endpoint command for a
different device could sneak in before we know if the first command is
completed.  If the first command dropped resources, the host controller
fails the command for some reason, and we're nearing the limit of
endpoints, we could end up oversubscribing the host.

To fix this race condition, when evaluating whether a configure endpoint
command will fix in our bandwidth budget, only add the new endpoints to
xhci->num_active_eps, and don't subtract the dropped endpoints.  Ignore
changed endpoints (ones that are dropped and then re-added), as that
shouldn't effect the host's endpoint resources.  When the configure
endpoint command completes, subtract off the dropped endpoints.

This may mean some configuration changes may temporarily fail, but it's
always better to under-subscribe than over-subscribe resources.

(Originally my plan had been to push the resource allocation down into the
ring allocation functions.  However, that would cause us to allocate
unnecessary resources when endpoints were changed, because the xHCI driver
allocates a new ring for the changed endpoint, and only deletes the old
ring once the Configure Endpoint command succeeds.  A further complication
would have been dealing with the per-device endpoint ring cache.)
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      2cf95c18
    • S
      Intel xhci: Ignore spurious successful event. · ad808333
      由 Sarah Sharp 提交于 
      The xHCI host controller in the Panther Point chipset sometimes produces
spurious events on the event ring.  If it receives a short packet, it
first puts a Transfer Event with a short transfer completion code on the
event ring.  Then it puts a Transfer Event with a successful completion
code on the ring for the same TD.  The xHCI driver correctly processes the
short transfer completion code, gives the URB back to the driver, and then
prints a warning in dmesg about the spurious event.  These warning
messages really fill up dmesg when an HD webcam is plugged into xHCI.

This spurious successful event behavior isn't technically disallowed by
the xHCI specification, so make the xHCI driver just ignore the spurious
completion event.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      ad808333
    • S
      Intel xhci: Support EHCI/xHCI port switching. · 69e848c2
      由 Sarah Sharp 提交于 
      The Intel Panther Point chipsets contain an EHCI and xHCI host controller
that shares some number of skew-dependent ports.  These ports can be
switched from the EHCI to the xHCI host (and vice versa) by a hardware MUX
that is controlled by registers in the xHCI PCI configuration space.  The
USB 3.0 SuperSpeed terminations on the xHCI ports can be controlled
separately from the USB 2.0 data wires.

This switchover mechanism is there to support users who do a custom
install of certain non-Linux operating systems that don't have official
USB 3.0 support.  By default, the ports are under EHCI, SuperSpeed
terminations are off, and USB 3.0 devices will show up under the EHCI
controller at reduced speeds.  (This was more palatable for the marketing
folks than having completely dead USB 3.0 ports if no xHCI drivers are
available.)  Users should be able to turn on xHCI by default through a
BIOS option, but users are happiest when they don't have to change random
BIOS settings.

This patch introduces a driver method to switchover the ports from EHCI to
xHCI before the EHCI driver finishes PCI enumeration.  We want to switch
the ports over before the USB core has the chance to enumerate devices
under EHCI, or boot from USB mass storage will fail if the boot device
connects under EHCI first, and then gets disconnected when the port
switches over to xHCI.

Add code to the xHCI PCI quirk to switch the ports from EHCI to xHCI.  The
PCI quirks code will run before any other PCI probe function is called, so
this avoids the issue with boot devices.

Another issue is with BIOS behavior during system resume from hibernate.
If the BIOS doesn't support xHCI, it may switch the devices under EHCI to
allow use of the USB keyboard, mice, and mass storage devices.  It's
supposed to remember the value of the port routing registers and switch
them back when the OS attempts to take control of the xHCI host controller,
but we all know not to trust BIOS writers.

Make both the xHCI driver and the EHCI driver attempt to switchover the
ports in their PCI resume functions.  We can't guarantee which PCI device
will be resumed first, so this avoids any race conditions.  Writing a '1'
to an already set port switchover bit or a '0' to a cleared port switchover
bit should have no effect.

The xHCI PCI configuration registers will be documented in the EDS-level
chipset spec, which is not public yet.  I have permission from legal and
the Intel chipset group to release this patch early to allow good Linux
support at product launch.  I've tried to document the registers as much
as possible, so please let me know if anything is unclear.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
      69e848c2
  5. 27 5月, 2011 25 次提交