8192eu has it's own IQK calibration procedure, and notably uses
undocumented RF register 0x56 in the process.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Fixup another case where the hard coded register value was used
instead of the name.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Set REG_QUEUE_CTRL and REG_ACLK_MON for 8192eu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Implement workaround for LDPC RX hands on 8192eu. This was inspired by
workaround found in the 8192eu vendor driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The vendor driver set register 0xfe58 REG_USB_HWPWM in it's init
sequence for 8192eu. Do the same here.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Set HIMR[01] on 8192eu instead of HISR/HIMR. It's not obvious this
really matters for USB devices, but this matches the register writes
performed by the vendor driver.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Set REG_AFE_XTAL_CTRL on 8192eu to the vendor driver value, and do not
skip setting REG_MAX_AGGR_NUM on 8192eu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu requires clearing/restoring bit 17 in REG_FPGA0_POWER_SAVE
before/after writing RF registers.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu does not use REG_AFE_PLL_CTRL in it's BB init sequence, so
provide device specific handling.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu efuse only has power data for path A and B. It follows the
same layout as 8723bu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Pick PHY init table based on device before distinguishing between
1T/2T/high PA tables. The latter is only currently used for
8188cu/8192cu/8188ru.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu also requires it's own PHY init table.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

A device specific AGC table is required for the 8192eu as well.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add the required radio init tables for 8192eu devices.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu also has it's own TRXFF boundary value to set.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

To match the vendor driver, do not mess with AFE_XTAL_CTRL on 8192eu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu requires a different MAC init table. Add the missing table
and specify the table to use in the fileops structure.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This enum is already perfectly aliased to enum nl80211_band, and
the only reason for it is that we get IEEE80211_NUM_BANDS out of
it. There's no really good reason to not declare the number of
bands in nl80211 though, so do that and remove the cfg80211 one.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Per the vendor driver, it looks like the 8192eu doesn't have LDOA15 /
LDOV12 registers.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8192eu uses the same H2C API as the 8723bu. Call the correct
functions for update_rate_mask() and report_connect().
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

8192eu A/B cut parts were incorrectly identified as 8192cu devices.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With support for more chips being added, use an enum to specify the
chip version.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

8192eu uses the new TX descriptor format
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is no short GI bit in the txdesc40 format.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

With the size based naming of TX descriptors. Change the bit
definition namings to indicate which descriptor format they match,
rather than having a device name in the bit name.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

There are two major types of TX descriptor formats for the RTL parts,
the old 32 byte descriptor, and the newer 40 byte descriptor used by
the 8723bu, 8192eu, and 88xx series.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

To reduce the patch volume, temporariliy disable 8192eu device init.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

8723b needs more action, so implement support for device specific
reset functions.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Only print a warning if the FIFO flush fails, as opposed to printing
the status unconditionally.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This should help when reloading the driver for 8723bu devices
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Implment 8723bu specific device power down, and make power_off() a
fileops function.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Powering up the 8723bu RF should probably be matched by the ability to
power it down again.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Use the bit define rather than hard code the value for REG_PWR_DATA bits.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

rtl8723bu_init_bt() is effectively the function enabling RF, so name
it appropriately.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This removes an superfluous semicolon.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

rtl8xxxu_rx_parse_phystats() only needs the RX rate to determine
whether to handle the stats as CCK or not. Parsing in the rate rather
than the rx descriptor elimantes the need to handle multiple rx
descriptor formats in the function.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Handle RA_REPORTS events for 8723bu to not have them show up as
unhandled.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Dump the contents of unhandled C2H events. We should be handling all
expected events, so this is debugging help in case an unexpected event
happens.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Implement support for nextgen devices reporting connectition to the
firmware.

The H2C API for reporting connection to the firmware is different
between the two device generations. Use the fileops structure to
determine which one to call.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Support for setting bandwidth and VHT parameters is still missing
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>