Section to describe the backlight for the LCD panels.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Sections to describe the pwm-leds in the system.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

We have proper driver stack to handle the pmu_stat LED which is connected
PWMB of twl4030.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Enable support for the PWMs and LED as PWM drivers.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Enable support for the PWMs and LEDs as PWM drivers.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add a new address space/memory resource to d_can device tree node. D_CAN
RAM initialization is achieved through RAMINIT register which is part of
AM33XX control module address space. D_CAN RAM init or de-init should be
done by writing instance corresponding value to control module register.

Till we have a separate control module driver to write to control module,
d_can driver will handle the register writes to control module by itself.
So a new address space to represent this control module register is added
to d_can driver.
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add d_can instances to aliases node to get the D_CAN instance number
from the driver. To initialize D_CAN message RAM, corresponding instance
number is required.

To initialize instance 0 message RAM then 0x1 should be written and for
instance 1 message RAM, 0x2 should be written to control module register.

With device-tree framework ip instance number is "-1" by default for all
instances. To get device id/instance number then modules should be added
to DT "aliases" node. of_alias_get_id() gives the device id number based
on number of alias nodes present in "aliases node".
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

This is a follow-up to Javier Martinez effort adding initial
device tree support to IGEP technology devices [1].

It adds uart1 and uart2 bindings to the generic dtsi for the IGEP boards.

[1] http://www.spinics.net/lists/linux-omap/msg83409.htmlSigned-off-by: NMatthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

ISEE IGEP COM Module is an TI OMAP3 SoC computer on module.

This patch adds an initial device tree support to boot an
IGEP COM Module from the MMC/SD.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
[b-cousson@ti.com: Update the Makefile for 3.8-rc2]
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

ISEE IGEPv2 is an TI OMAP3 SoC based embedded board.

This patch adds an initial device tree support to boot
an IGEPv2 from the MMC/SD.

Currently is working everything that is supported by DT
on OMAP3 SoCs (MMC/SD, GPIO LEDs, EEPROM, TWL4030 audio).
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
[benoit.cousson@linaro.org: Update the Makefile for 3.8-rc2]
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Add a generic .dtsi device tree source file for the
common characteristics across IGEP Technology devices.
Signed-off-by: NJavier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: NMatthias Brugger <matthias.bgg@gmail.com>
Tested-by: NEnric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Rename I2C and GPIO nodes according to AM33XX TRM. According to
AM33XX TRM device instances are starting from "0" like i2c0, i2c1
and i2c3.
Signed-off-by: NPantelis Antoniou <panto@antoniou-consulting.com>
[panto@antoniou-consulting.com: initial patch by pantelis's]
Signed-off-by: NAnilKumar Ch <anilkumar@ti.com>
Signed-off-by: NBenoit Cousson <benoit.cousson@linaro.org>

Merge tag 'omap-devel-b-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into for_3.10/dts_merged

Provide RESET and Power regulators for the USB PHY,
the USB Host port mode and the PHY device.

Also provide pin multiplexer information for USB host
pins.

CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adds device nodes for HS USB Host module, TLL module,
OHCI and EHCI controllers.

CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Adds device nodes for HS USB Host module, TLL module,
OHCI and EHCI controllers.

CC: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and NOP PHY device. VAUX2 supplies the PHY's VCC.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulator
and the NOP PHY device. VAUX2 supplies the PHY's VCC.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Remove deprecated USBHS platform data.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's VCC and RESET
regulators and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's RESET regulators
and the NOP PHY devices.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's VCC and RESET
regulators and the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Use usbhs_init_phys() to register the PHY's VCC and RESET
regulators and the NOP PHY device.

Get rid of managing the PHY clock as it will be done by the PHY driver.
For that to work we create a clock alias that links the PHY clock name
to the PHY device name.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This helper allows board support code to add the PHY's
VCC and RESET regulators which are GPIO controlled as well
as the NOP PHY device.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

omap3_noncore_dpll_set_rate() attempts an enable of bypass clk as well
as ref clk for every .set_rate attempt on a noncore DPLL, regardless of
whether the .set_rate results in the DPLL being locked or put in bypass.
Early at boot, while some of these DPLLs are programmed and locked
(using .set_rate for the DPLL), this causes an ordering issue.

For instance, on OMAP5, the USB DPLL derives its bypass clk from ABE DPLL.
If a .set_rate of USB DPLL which programmes the M,N and locks it is called
before the one for ABE, the enable of USB bypass clk (derived from ABE DPLL)
then attempts to lock the ABE DPLL and fails as the M,N values for ABE
are yet to be programmed.

To get rid of this ordering needs, enable bypass clk for a DPLL as part
of its .set_rate only when its being put in bypass, and only enable the
ref clk when its locked.
Reported-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

_pwrdm_save_clkdm_state_and_activate() tried to test one of its
unsigned arguments to determine whether it was less than zero.  Fix by
moving the error test to the caller.
Reported-by: NChen Gang <gang.chen@asianux.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

_HWMOD_WAKEUP_ENABLED is currently unused across the hwmod
framework. Just get rid of it, so we have one less flag to
worry about.
Tested-by: NVaibhav Bedia <vaibhav.bedia@ti.com>
Signed-off-by: NRajendra Nayak <rnayak@ti.com>
Signed-off-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>

WDT1 module can take one of the below clocks as input functional
clock -
     - On-Chip 32K RC Osc [default/reset]
     - 32K from PRCM

The On-Chip 32K RC Osc clock is not an accurate clock-source as per
the design/spec, so as a result, for example, timer which supposed
to get expired @60Sec, but will expire somewhere ~@40Sec, which is
not expected by any use-case.

The solution here is to switch the input clock-source to PRCM
generated 32K clock-source during boot-time itself.
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoit Cousson <benoit.cousson@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>

This patch adds sysc definitions to the wdt1 hwmod entry, which in-turn
makes sure that sysc idle bit-fields are configured to valid state on
enable/disable callbacks.

With the recent submitted patch from Santosh Shilimkar,
"ARM: OMAP2+: hwmod: Don't call _init_mpu_rt_base if no sysc"
(commit: 4a98c2d89), it is required to add sysconf
information to each valid hwmod entry, else device will not be
come out from idle state properly and leads to below kernel
crash  -

[2.190237] Unhandled fault: external abort on non-linefetch (0x1028) at
0xf9e35034
[2.198325] Internal error: : 1028 [#1] SMP ARM
[2.203101] Modules linked in:
[2.206334] CPU: 0    Not tainted  (3.9.0-rc3-00059-gd114294#1)
[2.212679] PC is at omap_wdt_disable.clone.5+0xc/0x60
[2.218090] LR is at omap_wdt_probe+0x184/0x1fc
Signed-off-by: NVaibhav Hiremath <hvaibhav@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Benoit Cousson <benoit.cousson@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>

Pull slave-dmaengine fixes from Vinod Koul:
 "Two fixes for slave-dmaengine.

  The first one is for making slave_id value correct for dw_dmac and
  the other one fixes the endieness in DT parsing"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dw_dmac: adjust slave_id accordingly to request line base
  dmaengine: dw_dma: fix endianess for DT xlate function