Since WE7 /proc/net/wireless checks whether level and noise  are in dBm
and shows them accordingly. Indicate that we return signal and noice
levels in dBm.

Before:
Inter-| sta-|   Quality        |   Discarded packets               | Missed | WE
 face | tus | link level noise |  nwid  crypt   frag  retry   misc | beacon | 22
  eth1: 0000   65.  219.  165.       0      0    148     41      0        0

After:
Inter-| sta-|   Quality        |   Discarded packets               | Missed | WE
 face | tus | link level noise |  nwid  crypt   frag  retry   misc | beacon | 22
  eth1: 0000   65.  -37.  -91.       0      0      0      0      0        0

While at it, replace raw numbers with appropriate macro.
Signed-off-by: NAndrey Borzenkov <arvidjaar@mail.ru>
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This fixes the poor wireless connection which happens even
if we are very well in the range.

Signed-off-by: Don.breslin@atheros.com
Signed-off-by: NVasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

As was pointed out in "p54: honour bss_info_changed's short slot time settings",
bss_info_changed provides more useful settings that can be used by the driver.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Johannes pointed out that the driver has cache the firmware for
suspend/resume cycles.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch contains only contains a one-liner fixes and enhancements
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch enables Mesh Point operation for any p54 device.
Signed-off-by: NChristian Lamparter <chunkeey@web.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make the DMAable mameory consistent with pci_set_consistent_dma_mask().
The DMA-mapping.txt Documentation recommends this but for PCI-X
considerations and on strange architecture like SGI SN2, not sure
why it would fix an issue but lets see if it does, just in case.

Before this, this driver was tested with x86_64 with about
7 GB of RAM, not sure if this is really needed.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use DMA_32BIT_MASK to clarify we only want 32-bit DMA
memory. What was there before is also 32-bit but this makes it
clearer
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Instead of hardcoding the used in/out endpoints
we should detect them by walking through all
available endpoints.

rt2800usb will gain the most out of this, because
the legacy drivers indicate that there are multiple
endpoints available.
However this code might benefit at least rt73usb as
well for the MIMO queues, and if we are really lucky
rt2500usb will benefit because for the TX and PRIO
queues.

Even if rt2500usb and rt73usb do not get better performance
after this patch, the endpoint detection still belongs to
rt2x00usb, and it shouldn't hurt to always try to detect
the available endpoints.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After considerable testing, the initial fears that the driver might damage
some flavors of RTL8187B hardware seem to be groundless. Accordingly, the
logged warning is removed. In addition, Kconfig is changed to remove the
dependence on EXPERIMENTAL.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger>
Acked-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Realtek 8187B has a receive command queue to feedback beacon interrupt
and transmitted packet status. Use it to feedback mac80211 about status
of transmitted packets. Unfortunately in the course of testing I found
that the sequence number reported by hardware includes entire sequence
control in a 12 bit only field, so a workaround is done to check only
lowest bits.
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add conf_tx callback and use it to configure tx queues of 8187L/8187B.
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hin-Tak Leung reported that after the change "rtl8187: add short slot
handling for 8187B" his RTL8187B started to give low throughput on
network transfers. Turns out that the SIFS setting used isn't ok, it
doesn't look to be the real aSIFSTime, using the "magical" 0x22 value
like on other 818x variants as the vendor does too fixes the issue.
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Tested-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Race condition causes RX buffers to be accessed even before it is
initialized. The RX and TX buffers are initialized immediately after
the hardware is registered with mac80211. The mac80211 start callback
is ready to be fired once the device is registered for a case when the
wpa_supplicant is also running at the same time.

The same race condition is also possible for RKFILL registration
as RFKILL init happens after the device registration with mac80211
and it is possible that rfkill_register would be called even before
it is initialized.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k frees irq even before IRQs are disabled and existing IRQs
are flushed when rfkill_register() fails.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Currently, ath9k builds RFKILL feature only when the RFKILL subsystem
is built part of the kernel. Build RFKILL feature regardless of whether
RFKILL subsystem is built as a MODULE or part of the kernel.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes incorrect noise floor threshold values.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

init values update for various atheros chipsets.
Signed-off-by: NSenthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This enables the custom firmware regulatory solution option
on iwlwifi drivers. These devices are uncapable of mapping their
EEPROM regulatory domain to a specific ISO / IEC alpha2.
Although the new 11n devices (>= iwl 5000) have only
3 regultaory SKUs -- MOW, ABG (no N) and BG -- the older
devices (3945 and 4965) have a more complex SKU arrangement
and therefore its not practical to move this to the driver.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fix value of upper FH register bound plus
it reorders and groups registers in more readable way
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Acked-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch cleans up some flow handler related document. It also
removes some blank lines.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Acked-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch rewrites the mac80211 configure_filter handler to better mapping
mac80211 filter flags to iwlwifi hardware filter flags. We now can support
5 mac80211 filter flags: FIF_OTHER_BSS, FIF_ALLMULTI, FIF_PROMISC_IN_BSS,
FIF_BCN_PRBRESP_PROMISC and FIF_CONTROL. This patch also avoids reconnecting
if the filter flags are changed when the STA is associated. Because rx_assoc
is used when full rxon is not necessary.
Signed-off-by: NZhu Yi <yi.zhu@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch fixes checkpatch.pl errors for iwlwifi.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

use IWL_CCK_RATES_MASK and IWL_OFDM_RATES_MASK instead of
their values directly.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
cc: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch
1. Removes use once use only fc variables, they are useless after refactoring
ieee80211 frame control handlers
2. Other trivial cleanups
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch moves code around and group most of the station
management code into iwl-sta.c

No functional changes (yet)
Signed-off-by: NTomas Winkler <tomas.winkler@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Patch aligns iwl3945_pci_probe with iwlwifi's iwl_pci_probe.
Added few comments and code simplified to make readable.
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The callback function write_tx_data() can only fail
when our ENTRY_OWNER_DEVICE_DATA flag on a queue entry
failed to determine the entry was not available and
it is in fact still owned by the hardware.
This means that if that function fails the queue
must be stopped in mac80211.

When rt2x00queue_get_queue() returns NULL in the TX
path, it means mac80211 has passed us an invalid queue,
although this should be impossible, it shouldn't hurt
if we send mac80211 a signal to stop the queue either.

Both issues can simply be resolved by removing their
manual failure handler and making them use the failure path
provided in rt2x00mac_tx().
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2500usb and rt73usb have different register word sizes,
for that reason the register access wrappers were never
moved into rt2x00usb.
With rt2800usb on its way, we should favor the 32bit
register access and move those wrappers into rt2x00usb.
That saves duplicate code, since only rt2500usb will
need the special 16bit wrappers.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

All code which accessed indirect registers was similar
in respect to the for-loop, the given timeout, etc.
Move it into a seperate function, which for PCI drivers
can be moved into rt2x00pci.

This allows us to cleanup the cleanup the code further
by removing the goto statementsand making the codepath
look a bit nicer.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Call the ath5k pci driver struct "ath5k" too to be less
confusing in sysfs.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NNick Kossifidis <mickflemm@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Modify the file comments to reflect the current maintainers.
Signed-off-by: NLarry Finger <Larry.Finger@lwfinger.net>
Acked-by: NHerton Ronaldo Krzesinski <herton@mandriva.com.br>
Acked-by: NHin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This updates rtl8180 handling for short slot after "mac80211: fix short
slot handling". Only rtl8180_rtl8225 actually had code for handling
short slot times, so the other RF devices are untouched by this change.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The old ieee80211 code only remains as a support library for the ipw2100
and ipw2200 drivers.  So, move the code and rename it appropriately to
reflects it's true purpose and status.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

These bits are shared already between ipw2x00 and hostap, and could
probably be shared both more cleanly and with other drivers.  This
commit simply relocates the code to lib80211 and adjusts the drivers
appropriately.
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

orinoco_translate_scan() and orinoco_translate_ext_scan() wrongly
truncate last_scanned argument from unsigned long to unsigned int.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Indirect registers require multiple calls to the CSR
register in order to access the indirect registers.
This must be protected under a lock to prevent race
conditions which could cause invalid data to
be returned when reading from the indirect register or silent
failures when writing data to the indirect register.

USB drivers where already protected under a mutex,
so rename the mutex and make PCI drivers use the mutex
as well.
This now means that BBP and RF registers are no longer
accessible in interrupt context. That is not a bad
situation since the slow behavior of accessing
those registers means we don't _want_ to access them
in interrupt context either.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

We can optimize get_duration and get_duration_res
by making them a macro. They are really simple
calculation handlers so this doesn't matter much.

Often (especially in rt2400pci and rt2500pci,
the arguments are hardcoded, and the result value
is passed into other hardcoded values.

By making the functions a macro GCC can
optimize the entire thing much better.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>