struct uart_omap_port and struct uart_omap_dma, and associated
definitions are private to the driver, so there's no point them sitting
in an include file under arch/arm.  Move them into the driver itself.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

irq_pending is never used, so let's remove it.  It seems to be  result
of a bad rebase of d37c6ceb (serial: omap: move uart_omap_port
definition to C file)
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The MCR TCRTLR bit can only be changed when ECB is set in the EFR.
Unfortunately, several places were trying to alter this bit while ECB
was clear:

- serial_omap_configure_xonxoff() was attempting to clear the bit after
  explicitly clearing the ECB bit.
- serial_omap_set_termios() was trying the same trick after setting the
  SCR, and when trying to change the TCR register when hardware flow
  control was enabled.

Fix this by ensuring that we always have ECB set whenever the TCRTLR bit
is changed.

Moreover, we start out by reading the EFR and MCR registers, which may
have indeterminent bit settings for the ECB and TCRTLR bits.  Ensure
that these bits always start off in a known state.

In order to avoid any undesired behaviour appearing through fixing this,
we also ensure that hardware assisted flow control is disabled while new
driver specific parts are not in place.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

c538d20c (and maybe previous commits) broke set_mctrl() by making
it only capable of setting bits in the MCR register.  This prevents
software controlled flow control and modem control line manipulation
via TIOCMSET/TIOCMBIC from working correctly.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There's no need to re-read EFR after we've recently written it; the
register is a configuration register which doesn't change its value
without us writing to it.  The last value which was written to this
register was up->efr.

Removing this re-reading avoids the possibility that we end up with
up->efr having unintended bits set, which should only be temporarily
set when accessing the enhanced features.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

The SCD (special character detect) bit enables comparisons with XOFF2,
which we do not program.  As the XOFF2 character remains unprogrammed,
there's little point enabling this feature along with its associated
interrupt.  Remove this, and ensure that the SCD bit is cleared.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

Nothing was clearing the UART_MCR_XONANY bit, so once the ixany
mode gets set, there's no possibility to disable it.  Clear this
bit when IXANY mode is cleared.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

There is nothing which clears the auto RTS/CTS bits, so once hardware
flow control gets enabled, there's no possibility to disable it.
So, clear these bits when CRTSCTS is cleared.
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>

This reverts commit 957ee727
(serial: omap: fix software flow control).

As Russell has pointed out, that commit isn't fixing
Software Flow Control at all, and it actually makes
it even more broken.

It was agreed to revert this commit and use Russell's
latest UART patches instead.

Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch does the following
- In case of errors if there least one data character in the RX FIFO
read it otherwise it may stall the receiver.

This is recommended in the interrupt reset method in the table 23-246 of
the omap4 TRM.
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NKevin Hilman <khilman@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Drop the check for "up" being valid on suspend/resume callbacks.
It should be valid always. Get rid of the "pdata" check also as
serial_omap_get_context_loss_count() checks for it.

Tested on omap4 panda and 3630 based Beagle board.
Signed-off-by: NSourav Poddar <sourav.poddar@ti.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Request pins using pinctrl framework. Only show a warning
on error as some boards set the pins in the bootloader
even if CONFIG_PINCTRL is enabled.
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

OMAP Architecture code, passes a few function
pointers for UART driver to use in order to
properly implement Power Management and Wakeup
capabilities.

The problem is that those function pointers,
which are passed (ab)using platform_data on
non-DT kernels, can't be passed down to drivers
through DT.

commit e5b57c03 (serial: omap: define helpers
for pdata function pointers) failed to take DT
kernels into consideration and caused a regression
to DT kernel boot.

Fix that by (re-)adding a check for valid pdata
pointer together with valid pdata->$FUNCTION
pointer.
Reported-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

when rebasing patches on top of Greg's tty-next,
it looks like automerge broke a few things which
I didn't catch (for whatever reason I didn't
have OMAP Serial enabled on .config) so I ended
up breaking the build on Greg's tty-next branch.

Fix the breakage by re-adding the three missing
members on struct uart_omap_port.
Reported-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

enable RX FIFO for 16 characters and TX FIFO
for 16 spaces.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

nobody needs to access the uart_omap_port structure
other than omap-serial.c file. Let's move that
structure definition to the C source file in order
to prevent anyone from accessing our structure.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

this driver doesn't use any from <plat/dmtimer.h>, so
we can remove it without any problems.

This will, however cause a problem because omap-serial.c
was relying on indirect inclusion of <linux/platform_device.h>,
let's fix the issue by including <linux/platform_device.h>
on omap-serial.c as it should be.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Software flow control register bits were not defined correctly.

Also clarify the IXON and IXOFF logic to reflect what userspace wants.

Cc: stable@vger.kernel.org
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

if we would reach serial_omap_get_char() while
Data Ready bit isn't set, we would return from
it without kicking our pm timer. This would mean
we would, eventually, have an unbalanced
pm_runtime_get on our device which would prevent
it from ever sleeping again.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This has been missing from OMAP UART driver
for quite a while and it's simple enough
to implement it.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch unlocks the port lock before calling a serial_core API
and re-acquires the port lock after calling it.
This patch fixes a system freeze issue seen when the serial_core
API uart_write_wakeup() eventually attempts to acquire the port lock
already acquired by omap serial interrupt handler.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NRuchika Kharwar <ruchika@ti.com>
Signed-off-by: NPavan Savoy <pavan_savoy@ti.com>
Signed-off-by: NVijay Badawadagi <bvijay@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

it makes no sense to mark our IRQ handler inline
since it's passed as a function pointer when
enabling the IRQ line.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Two functions:
omap_serial_fill_features_erratas() and
of_get_uart_port_info() are only called from probe().
Marking them as __devinit gives us another
oportunity to free some code after .init.text
is done.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NRuchika Kharwar <ruchika@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

pm_runtime_enable() needs to be invoked before
pm_runtime_use_autosuspend(), and
pm_runtime_set_autosuspend_delay() functions.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NRuchika Kharwar <ruchika@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When we're running our hardirq handler, there's
not need to disable IRQs with spin_lock_irqsave()
because IRQs are already disabled. It also makes
no difference if we save or not IRQ flags.

Switch over to simple spin_lock/spin_unlock and
drop the "flags" variable.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

before removing the driver, let's make sure
to force device into a suspended state in order
to conserve power.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

if platform_get_drvdata() returns NULL, that's
quite a nasty bug on the driver which we want to
catch ASAP. Otherwise, that check is hugely
unneeded.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

by the time we call our first pm_runtme_get_sync()
after enable pm_runtime, our resume method might
be called. To avoid problems, we must make sure
that our dev->drvdata is set correctly before
our resume method gets called.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Everytime we're done using our TTY, we want
the pm timer to be reinitilized. By sticking
to pm_runtime_pm_autosuspend() we make sure
that this will always be the case.

The idea behind this patch is to make sure we
will always reinitialize the pm timer so that
we don't fall into a situation where pm_runtime_put()
expires right away (if timer was already about to
expire when we made the call to pm_runtime_put()).

While suspending right away wouldn't cause any
issues, reinitializing the pm timer can help us
avoiding unnecessary context save & restore
operations (which are somewhat expensive) if there's
another read/write/set_termios request coming right
after. IOW, we are trying to make sure UART is still
powered up while it's still under heavy usage.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

since all other IRQ types now do all necessary
checks inside their handlers, transmit_chars()
was the only one left expecting serial_omap_irq()
to check THRE for it. We can move THRE check to
transmit_chars() in order to make serial_omap_irq()
more uniform.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

receive_chars() was getting too big and too difficult
to follow. By splitting it into separate RDI and RSLI
handlers, we have smaller functions which are easy
to understand and only touch the pieces which they need
to touch.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

quite a few changes here, though they are
pretty obvious. In summary we're making sure
to detect which interrupt type we need to
handle before calling the underlying interrupt
handling procedure.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The current support is known to be broken and
a later patch will come re-adding it using
dma engine API.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The driver doesn't need to know about its platform_device.

Everything the driver needs can be done through the
struct device pointer. In case we need to use the
OMAP-specific PM function pointers, those can make
sure to find the device's platform_device pointer
so they can find the struct omap_device through
pdev->archdata field.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

this patch is in preparation to a few other changes
which will align on the prototype for function
pointers passed through pdata.

It also helps cleaning up the driver a little by
agregating checks for pdata in a single location.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

current code only works because struct uart_port
is the first member on the uart_omap_port structure.

If, for whatever reason, someone puts another
member as the first of the structure, that cast
won't work anymore. In order to be safe, let's use
a container_of() which, for now, gets optimized into
a cast anyway.
Tested-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Acked-by: NSantosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

flush[_delayed]_work_sync() are now spurious.  Mark them deprecated
and convert all users to flush[_delayed]_work().

If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.

This patch doesn't make any functional difference.
Signed-off-by: NTejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com> 

OMAP hardware doesn't provide a phyisical DTR line, but
some configurations may need a DTR line which tracks whether
the device is open or not.

So allow a gpio to be configured as the DTR line.
Signed-off-by: NNeilBrown <neilb@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently the errata is populated based on cpu checks this can
be removed and replaced with module version check of uart ip block.
MVR reg is provided within the uart reg map use the same
to populate the errata and thus now errata population and handling
can be managed within the driver itself.

Cc: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGovindraj.R <govindraj.raja@ti.com>
Reviewed-by: NJon Hunter <jon-hunter@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The patch does the following

- The pm_runtime_disable is called in the remove not in the error
  case of probe.The patch calls the pm_runtime_disable in the error
  case.
- Calls pm_runtime_put in the error case.
- The  up is not freed in the error path. Fix the memory leak by using
  devm_* so that the memory need not be freed in the driver.
- Also the iounmap is not called fix the same by calling using devm_ioremap.
- Make the name of the error tags more meaningful.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: NShubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>