This mechanism introduced in this patch applies (at least) for hardware
designs using a single shared antenna for both WLAN and BT. In these designs,
the antenna must be toggled between WLAN and BT.

In those hardware, managing WLAN co-existence with Bluetooth requires WLAN
full power save whenever there is Bluetooth activity in order for WLAN to be
able to periodically relinquish the antenna to be used for BT. This is because
BT can only access the shared antenna when WLAN is idle or asleep.

Some hardware, for instance the wl1271, are able to indicate to the host
whenever there is BT traffic. In essence, the hardware will send an indication
to the host whenever there is, for example, SCO traffic or A2DP traffic, and
will send another indication when the traffic is over.

The hardware gets information of Bluetooth traffic via hardware co-existence
control lines - these lines are used to negotiate the shared antenna
ownership. The hardware will give the antenna to BT whenever WLAN is sleeping.

This patch adds the interface to mac80211 to facilitate temporarily disabling
of dynamic power save as per request of the WLAN driver. This interface will
immediately force WLAN to full powersave, hence allowing BT coexistence as
described above.

In these kind of shared antenna desings, when WLAN powersave is fully disabled,
Bluetooth will not work simultaneously with WLAN at all. This patch does not
address that problem. This interface will not change PSM state, so if PSM is
disabled it will remain so. Solving this problem requires knowledge about BT
state, and is best done in user-space.
Signed-off-by: NJuuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix the following compile warning:

CC [M]  net/mac80211/scan.o
net/mac80211/scan.c: In function 'ieee80211_request_internal_scan':
net/mac80211/scan.c:749:23: warning: comparison between 'enum nl80211_band' and 'enum ieee80211_band'

caused by the local variable band not being of the proper 'ieee80211_band' type.
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The message following fatal DMA errors fails to indicate properly that the
driver has switched to PIO mode.
Signed-off-by: NLarry Finger <Larry.Finger@wfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove the reference to non-exist function in iwlcore
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Break out of loop and log the error message when encounter error; this is
better approach than using "goto".
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

All the calibrations are "agn" only functions, move from iwlcore to
iwlagn.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

agn and 3945 has different statistics_notif data structure; since 3945
has it statistics_notif data structure inside the _3945 portion of
iwl_priv, it make sense to move the agn statistics_notif into _agn
portion.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

To avoid having unnecessary functions in iwlcore.ko, those that
are not shared by agn and 3945, move agn specific rx related code
to iwl-agn-rx.c.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

errors are defined in hex but displayed as decimal.  displaying as hex
debugging easier and eliminated having to manually convert.
Signed-off-by: NJay Sternberg <jay.e.sternberg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

When station management calls to ucode return
an error we could previously do nothing, but
now that almost all calls are synchronous we
can actually let the error bubble up. Use EIO
as the error as it best indicates a problem
with the device.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Key management can use sync commands
instead of asynchronous ones to have
better error checking.

Also add checks that the commands all
should have the mutex held.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Now that the ampdu_action callback can sleep,
we can use the mutex to properly protect the
aggregation data, and return useful errors if
they should happen.

Also, add some sleep and mutex debugging so
we won't call any of the functions that now
require being able to sleep and/or the mutex
to be held in an invalid context.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>

Currently, detection in hwsim and ath9k can
detect that two sw scans are in flight at the
same time, which isn't really true. It is
caused by a race condition, because the scan
complete callback is called too late, after
the lock has been dropped, so that a new scan
can be started before it is called.

It is also called too early semantically, as
it is currently called _after_ the return to
the operating channel -- it should be before
so that drivers know this is the operating
channel again.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Since mac80211 will not set the max_scan parameters
if hw scan is enabled, hwsim needs to do it so that
cfg80211 won't reject the scan.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

regulatory_init is only called by cfg80211_init which is in .init.text,
too.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

cfg80211_exit is only used as module_exit function, so it can go to
.exit.text saving a few bytes when CONFIG_CFG80211=y.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch adds USB IDs for some more supported
devices.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The below patch fixes a warning message when compiling with gcc 4.6.0
  CC [M]  drivers/net/wireless/hostap/hostap_ap.o
drivers/net/wireless/hostap/hostap_ap.c: In function 'hostap_ap_tx_cb_assoc':
drivers/net/wireless/hostap/hostap_ap.c:691:6: warning: variable 'fc' set but not used
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The patch below fixes a warning message Im seeing with gcc 4.6.0
 CC [M]  drivers/net/wireless/hostap/hostap_main.o
drivers/net/wireless/hostap/hostap_main.c: In function 'hostap_set_multicast_list_queue':
drivers/net/wireless/hostap/hostap_main.c:744:27: warning: variable 'iface' set but not used
Signed-off-by: NJustin P. Mattock <justinmattock@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Conflicts:
	net/mac80211/mlme.c

regression introduced by b8d92c9c

In function ‘ieee80211_work_rx_queued_mgmt’:
warning: ‘rma’ may be used uninitialized in this function

this re-adds default value WORK_ACT_NONE back to rma
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Only report PHY error frames for ANI on chipsets which do not have PHY error
counters in hardware.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Reviewed RX descriptor functions against the HAL sources. Some minor changes:

  - check size before making changes to the descriptor

  - whitespace

  - add comments about 5210 timestamps. this needs to be adressed later!

  - FIFO overrun error only available on 5210

  - rs_phyerr should not be OR'ed

  - clear the whole ath5k_rx_status structure before using, instead of
    zeroing specific fields.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are some differences between 5210 and 5211 descriptors which we did not
take into account before.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Update 5210 frame types to match the HAL. We have to apply the same bitshift to
the constants as we use later.

Add 5211 specific frame types.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I carefully reviewed desh.h against the HAL sources. Added comments and made
differences between 5210, 5211 and 5212 more clear by adding _521x to the
defines which are specific to that chipset. Renamed some defines. No functional
changes.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath5k_hw_rx_error was only used once, where we could easily just use
ath5k_hw_rx_status as well, so remove it.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Just whitespace and indentation.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Use direct function calls for ath5k_hw_setup_rx_desc() and
ath5k_hw_setup_mrr_tx_desc() instead of a function pointer which always pointed
to the same function in the case of ath5k_hw_setup_rx_desc() and which is
easily unified in the case of ath5k_hw_setup_mrr_tx_desc().

Also simplify the initialization function for the remaining function pointers.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Create a new function ath5k_receive_frame_ok() which checks for errors, updates
error statistics and tells us if we want to further "receive" this frame or
not. This way we can avoid a goto and have a cleaner separation between buffer
handling and other things.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Move frame reception into it's own function to have a clearer separation
between buffer and descriptor handling and things that are done when we
actually receive a frame.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There is no reason for a special handling (return) here, just break like we do
with the checks before.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

After we free skbs for receive or transmit descriptors, make sure we have no
pointers to the now invalid memory address.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the debug ouptut rx_status_0 was printed twice instead of rx_status_1. Also
make the debug message more clear.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix comment about dma sizes, brackets were missing. Replace 'insure' with
'ensure'.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Rename ath5k_txbuf_free() to ath5k_txbuf_free_skb() since this is what it does:
it frees the skb and not the buf. Same for ath5k_rxbuf_free().
Signed-off-by: NBruno Randolf <br1@einfach.org>
Acked-by: NBob Copeland <me@bobcopeland.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add a debug print for every case of reset.
Signed-off-by: NBruno Randolf <br1@einfach.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

BugLink: http://bugs.launchpad.net/bugs/21367

Enable LED by default and update the MODULE_PARM_DESC.  The original
reason for defaulting to disabled was documented in 2005 and noted, "The
LED code has been reported to hang some systems when running ifconfig
and is therefore disabled by default."  This no longer appears
applicable and users have been requesting this be enabled for several
years.
Signed-off-by: NTJ <ubuntu@tjworld.net>
Signed-off-by: NTim Gardner <tim.gardner@canonical.com>
Signed-off-by: NAndy Whitcroft <apw@canonical.com>
Acked-by: NStefan Bader <stefan.bader@canonical.com>
Signed-off-by: NLeann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Medion MD40900 device id [0x0cde, 0x0006] is defined twice.
Comment out the duplicate.
Originally-by: NBen Collins <ben.collins@ubuntu.com>
Signed-off-by: NLeann Ogasawara <leann.ogasawara@canonical.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>