Change details:
 - Consolidated bfa_sm.h and bfa_wc.h into bfa_cs.h
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Heartbeat failure counter is not incrementing under some scenarios.
   Update hbfails and hb_count stats during hwerror event.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Added logic to unlock hw semaphore if the previos FW boot was from boot
   code (flash based) and the current FW initialization attempt is from OS
   driver.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Changed event name IOC_E_PFAILED to IOC_E_PFFAILED
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - If there is a command pending in the mailbox, bfa_ioc_mbox_queue() enqueues
   the mailbox command to a pending command queue. Entries in this queue are
   not flushed when IOC is disabled. As a result, when IOC is re-enabled again,
   the stale entries in the pending command queue are posted to the mailbox.
   When these mailbox commands are processed by the FW and responses are sent,
   unexpected  events are received by other modules' FSMs (f.e. bfa_msgq) which
   have not posted any mailbox commands after IOC was enabled.
 - Flush the pending mailbox command queue when IOC is disabled. Rename
   bfa_ioc_mbox_hbfail to bfa_ioc_mbox_flush. Call bfa_ioc_mbox_flush
   from bfa_iocpf_sm_disabled_entry()
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Always set mbox irq index to zero and make corresponding changes in mbox
   irq alloc/sync function and txrx irq index calculation. Add definition of
   BNAD_INTX_TX_IB_BITMASK & BNAD_INTX_RX_IB_BITMASK and update
   bnad_txrx_irq_alloc accordingly.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Chnage details:
 - The module name is not used in case of state machine fault, hence no longer
   passing the module name to the fault handler.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Replace IOC HB failure event notification with a more generic mechanism
   that is capable of sending enble, disable, and failed events to registered
   modules. As a result, cee  module event handling callback bfa_cee_hbfail()
   is replaced with bfa_cee_notify() so that it can receive and handle
   different events from IOC.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Driver cleanup as per new checkpatch v0.31
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change details:
 - Print the dirver version when module is loaded.
Signed-off-by: NRasesh Mody <rmody@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver reads PCI subsystem ID from the PCI configuration register while it's
already stored by the PCI subsystem in the 'subsystem_device' field of 'struct
pci_dev'...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver reads PCI subsystem IDs from the PCI configuration registers while
they are already stored by the PCI subsystem in the 'subsystem_{vendor|device}'
fields of 'struct pci_dev'...
Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

linux-next-20110722/drivers/bcma/driver_pci.c:175: error: 'SSB_PCICORE_BFL_NOPCI' undeclared (first use in this function)
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

With ib_qib options:

    options ib_qib krcvqs=1 pcie_caps=0x51 rcvhdrcnt=4096 singleport=1 ibmtu=4

a run of ib_write_bw -a yields the following:

    ------------------------------------------------------------------
     #bytes     #iterations    BW peak[MB/sec]    BW average[MB/sec]
     1048576   5000           2910.64            229.80
    ------------------------------------------------------------------

The top cpu use in a profile is:

    CPU: Intel Architectural Perfmon, speed 2400.15 MHz (estimated)
    Counted CPU_CLK_UNHALTED events (Clock cycles when not halted) with a unit mask
    of 0x00 (No unit mask) count 1002300
    Counted LLC_MISSES events (Last level cache demand requests from this core that
    missed the LLC) with a unit mask of 0x41 (No unit mask) count 10000
    samples  %        samples  %        app name                 symbol name
    15237    29.2642  964      17.1195  ib_qib.ko                qib_7322intr
    12320    23.6618  1040     18.4692  ib_qib.ko                handle_7322_errors
    4106      7.8860  0              0  vmlinux                  vsnprintf


Analysis of the stats, profile, the code, and the annotated profile indicate:
 - All of the overflow interrupts (one per packet overflow) are
   serviced on CPU0 with no mitigation on the frequency.
 - All of the receive interrupts are being serviced by CPU0.  (That is
   the way truescale.cmds statically allocates the kctx IRQs to CPU)
 - The code is spending all of its time servicing QIB_I_C_ERROR
   RcvEgrFullErr interrupts on CPU0, starving the packet receive
   processing.
 - The decode_err routine is very inefficient, using a printf variant
   to format a "%s" and continues to loop when the errs mask has been
   cleared.
 - Both qib_7322intr and handle_7322_errors read pci registers, which
   is very inefficient.

The fix does the following:
 - Adds a tasklet to service QIB_I_C_ERROR
 - Replaces the very inefficient scnprintf() with a memcpy().  A field
   is added to qib_hwerror_msgs to save the sizeof("string") at
   compile time so that a strlen is not needed during err_decode().
 - The most frequent errors (Overflows) are serviced first to exit the
   loop as early as possible.
 - The loop now exits as soon as the errs mask is clear rather than
   fruitlessly looping through the msp array.

With this fix the performance changes to:

    ------------------------------------------------------------------
     #bytes     #iterations    BW peak[MB/sec]    BW average[MB/sec]
     1048576   5000           2990.64            2941.35
    ------------------------------------------------------------------

During testing of the error handling overflow patch, it was determined
that some CPU's were slower when servicing both overflow and receive
interrupts on CPU0 with different MSI interrupt vectors.

This patch adds an option (krcvq01_no_msi) to not use a dedicated MSI
interrupt for kctx's < 2 and to service them on the default interrupt.
For some CPUs, the cost of the interrupt enter/exit is more costly
than then the additional PCI read in the default handler.
Signed-off-by: NMike Marciniszyn <mike.marciniszyn@qlogic.com>
Signed-off-by: NRoland Dreier <roland@purestorage.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Tested-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There are only two capabilities we need, and both are trivial to find.

ath5k_hw_hasbssidmask() is true on AR5212, but not on AR5210 or AR5211.

ath5k_hw_hasveol() is true on AR5211 and AR5212, but not on AR5210,
according to the HAL source.
Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NPavel Roskin <proski@gnu.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When using DMA, drivers need to pass special translation info to the
hardware.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove b43's workarounds at the same time. Other users of
ssb_dma_translation do not support any 64-bit DMA devices, so they are
not affected.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Analyze of MMIO dumps from BCM43224, BCM43225, BCM4313 and BCM4331 has
shown that wl disables parity check for all that cards. This is required
for receiving any packets from the hardware.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add forgotten entry into the global blacklist.
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

This patch drops transport_asciihex_to_binaryhex() in favor of proper
hex2bin usage from include/linux/kernel.h:hex2bin()
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Additionally this patch brings proper apply of the designator type.
However, the original code luckily has no bug, because the association
equals to 0.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: James Bottomley <jbottomley@parallels.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch adds the default 'Unrestricted reordering allowed' for SCSI
control mode page QUEUE ALGORITHM MODIFIER on a per se_device basis in
target_modesense_control() following spc4r23.  This includes a new
emuluate_rest_reord configfs attribute that currently (only) accepts
zero to signal 'Unrestricted reordering allowed' in control mode page
usage by the backend target device.
Reported-by: NRoland Dreier <roland@purestorage.com>
Signed-off-by: NNicholas Bellinger <nab@risingtidesystems.com>

This patch breaks up the ->map_task_SG() backend call into two seperate
->map_control_SG() and ->map_data_SG() in order to better address
IBLOCK and pSCSI.  IBLOCK only allocates bios for ->map_data_SG(), and
pSCSI will allocate a struct request for both cases.

This patch fixes incorrect usage of ->map_task_SG() for all se_cmd descriptors
in transport_generic_new_cmd() by moving the call into it's proper location
directly inside of transport_allocate_data_tasks()
Reported-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch contains the squashed version of forth round series cleanups
from Andy and Christoph following the post heavy lifting in the preceeding:
'Eliminate usage of struct se_mem' and 'Make all control CDBs scatter-gather'
changes.  This also includes a conversion of target core and the v3.0
mainline fabric modules (loopback and tcm_fc) to use pr_debug and the
CONFIG_DYNAMIC_DEBUG infrastructure!

These have been squashed into this third and final round for v3.1.

target: Remove ifdeffed code in t_g_process_write
target: Remove direct ramdisk code
target: Rename task_sg_num to task_sg_nents
target: Remove custom debug macros for pr_debug. Use pr_err().
target: Remove custom debug macros in mainline fabrics
target: Set WSNZ=1 in block limits VPD. Abort if WRITE_SAME sectors = 0
target: Remove transport do_se_mem_map callback
target: Further simplify transport_free_pages
target: Redo task allocation return value handling
target: Remove extra parentheses
target: change alloc_task call to take *cdb, not *cmd

(nab: Fix bogus struct file assignments in fd_do_readv and fd_do_writev)
Signed-off-by: NAndy Grover <agrover@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Both backstores and fabrics use arrays of struct scatterlist to describe
data buffers. However TCM used struct se_mems, basically a linked list
of scatterlist entries. We are able to simplify the code by eliminating
this intermediate data structure and just using struct scatterlist[]
throughout.

Also, moved attachment of task to cmd out of transport_generic_get_task
and into allocate_control_task and allocate_data_tasks. The reasoning
is that it's nonintuitive that get_task should automatically add it to
the cmd's task list -- it should just return an allocated, initialized
task. That's all it should do, based on the function's name, so either the
function shouldn't do it, or the name should change to encapsulate the
entire essence of what it does.

(nab: Fix compile warnings in tcm_fc, and make transport_kmap_first_data_page
 honor sg->offset for SGLs from contigious memory with TCM_Loop, and
 fix control se_cmd descriptor memory leak)
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Since sectors is not modified, it's more straightforward to do this.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Due to all cdbs' data buffers being referenced by scatterlists, buffers
of more than a page are not contiguous. Instead of handling this in all
control command handlers, we may be able to get away with just limiting
control cdb data buffers to one page. The only control CDBs we handle that
have potentially large data buffers are REPORT LUNS and UNMAP, so if we
didn't want to live with this limitation, they would need to be modified
to walk the pages in the data buffer's sgl.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Previously, some control CDBs did not allocate memory in pages for their
data buffer, but just did a kmalloc. This patch makes all cdbs allocate
pages.

This has the benefit of streamlining some paths that had to behave
differently when we used two allocation methods. The downside is that
all accesses to the data buffer need to kmap it before use, and need to
handle data in page-sized chunks if more than a page is needed for a given
command's data buffer.

Finally, note that cdbs with no data buffers are handled a little
differently. Before, SCSI_NON_DATA_CDBs would not call get_mem at all
(they'd be in the final else in transport_allocate_resources) but now
these will make it into generic_get_mem, but just not allocate any
buffers.
Signed-off-by: NAndy Grover <agrover@redhat.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Implement page B1h, Block Device Characteristics, so that we can report
a medium rotation rate of 1 (non-rotating / solid state) if the
is_nonrot device attribute is set; we update the iblock backend to set
this attribute if the underlying Linux block device has its nonrot
flag set.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

The current handling of VPD page 00h (Supported VPD Pages) for INQUIRY
commands has a couple of problems:

 - The page length field is incorrectly set to 3, so the entry for 86h
   (Extended INQUIRY Data) is ignored since it is in the fourth slot.
 - Even though the code handles pages B0h and B2h, those pages aren't
   mentioned in the Supported VPD Pages list, so eg the Linux SCSI stack
   won't actually try to use them.

Fix these problems and make things more robust to avoid future problems
by moving to a table of supported VPD pages, which means that any added
VPD page support will automatically get reported on page 0.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

In target_fabric_configfs_init(), we should allow fabric_mod to be NULL,
since THIS_MODULE is NULL for built-in modules.  The main method of
using the target code may be as modules, but having everything built-in
is useful eg to be able to do quick testing with "qemu -kernel".

In any case, we shouldn't bomb out fabric registration for a perfectly
valid configuration, so simply drop the check of fabric_mod.
Signed-off-by: NRoland Dreier <roland@purestorage.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

This patch converts ft_queue_cmd() to use wake_up_process() and
ft_thread() to use schedule_timeout_interruptible(MAX_SCHEDULE_TIMEOUT)
instead of wait_event_interruptible().  This fixes a potential race with
the wait_event_interruptible() conditional with qobj->queue_cnt in
ft_thread().

This patch also drops the unnecessary set_user_nice(current, -20) in
ft_thread(), and drops extra () around two if (!(acl)) conditionals in
tfc_conf.c.
Reported-by: NChristoph Hellwig <hch@infradead.org>
Signed-off-by: NNicholas A. Bellinger <nab@linux-iscsi.org>

This patch removes the unnecessary EXTRA_CFLAGS includes, and drops the
unused -DTCM_FC_DEBUG define.
Reported-by: NChristoph Hellwig <hch@infradead.org>
Signed-off-by: NNicholas A. Bellinger <nab@linux-iscsi.org>

There is a memory leak in tcm_loop_make_scsi_hba().

If all the strstr() calls return NULL and we end up at return ERR_PTR(-EINVAL);
then we'll be leaking the memory previously allocated to tl_hba as
that variable goes out of scope.

This patch should fix the leak.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NDan Carpenter <error27@gmail.com>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>

Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Signed-off-by: NNicholas Bellinger <nab@linux-iscsi.org>