This patch implements raw mode support for AF DASD in ipr driver
which allows for tools to send commands directly to physical
devices which are members of RAID arrays when enabled in the firmware.

[jejb: fix up whitespace]
Signed-off-by: Wen Xiong<wenxiong@linux.vnet.ibm.com>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Reviewed-by: NDaniel Kreling <kreling@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Re-enable write same support for ipr RAID adapters.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: NDaniel Kreling <kreling@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Fixes a possible oops during adapter initialization in some
memory allocation failure error paths scenarios.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: NDaniel Kreling <kreling@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

The pci_set_pcie_reset_state has changed semantics to not be callable
from interrupt context, so change ipr's usage of the API to comply with
this change by ensuring this occurs from a workqueue.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: NDaniel Kreling <kreling@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Currently when performing a reboot with an ipr adapter,
the adapter gets shutdown completely, flushing all write
cache, as well as performing a full hardware reset of the card
during the shutdown phase of the old kernel. This ensures
the adapter is in a fully quiesced state across the reboot.

There are scenarios, however, such as when performing
kexec, where this full adapter shutdown is not required
and not desired, since it can make the reboot process take
noticeably longer.

This patch adds a module parameter to allow for skipping the
full shutdown during reboot. Rather than performing a full
adapter shutdown and reset, we simply cancel any outstanding
error buffers, place the adapter into a state where it has no
memory of any DMA addresses from the old kernel, then disable
the device. This significantly speeds up kexec boot, particularly
in configurations with multiple ipr adapters.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Reviewed-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Reviewed-by: NDaniel Kreling <kreling@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Odin.com>

Fixes a race condition in abort handling that was injected
when multiple interrupt support was added. When only a single
interrupt is present, the adapter guarantees it will send
responses for aborted commands prior to the response for the
abort command itself. With multiple interrupts, these responses
generally come back on different interrupts, so we need to
ensure the abort thread waits until the aborted command is
complete so we don't perform a double completion. This race
condition was being hit frequently in environments which
were triggering command timeouts, which was resulting in
a double completion causing a kernel oops.

Cc: <stable@vger.kernel.org>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Reviewed-by: NWendy Xiong <wenxiong@linux.vnet.ibm.com>
Tested-by: NWendy Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Set the scsi_level correctly for disk arrays such
that things like the rotational field get set
properly by sd.c.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong<wenxiong@linux.vnet.ibm.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Switch device scanning logic in the ipr driver to use
the async scan API. This speeds up boot times, particularly
on large systems.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Reviewed-by: Wen Xiong<wenxiong@linux.vnet.ibm.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Both remaining users are better of just checking sdev->simple_tags
directly.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: NHannes Reinecke <hare@suse.de>

Since we got rid of ordered tag support in 2010 the prime use case of
switching on and off ordered tags has been obsolete.  The other function
of enabling/disabling tagging entirely has only been correctly implemented
by the 53c700 driver and isn't generally useful.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com
Reviewed-by: NHannes Reinecke <hare@suse.de>

Drop the now unused reason argument from the ->change_queue_depth method.
Also add a return value to scsi_adjust_queue_depth, and rename it to
scsi_change_queue_depth now that it can be used as the default
->change_queue_depth implementation.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>

Use dma_set_mask_and_coherent() to set both the DMA and coherent
DMA mask.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Even though the ipr driver is only used on PCI, convert it
to use the generic DMA API.
Signed-off-by: NAnton Blanchard <anton@samba.org>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Remove the tagged argument from scsi_adjust_queue_depth, and just let it
handle the queue depth.  For most drivers those two are fairly separate,
given that most modern drivers don't care about the SCSI "tagged" status
of a command at all, and many old drivers allow queuing of multiple
untagged commands in the driver.

Instead we start out with the ->simple_tags flag set before calling
->slave_configure, which is how all drivers actually looking at
->simple_tags except for one worke anyway.  The one other case looks
broken, but I've kept the behavior as-is for now.

Except for that we only change ->simple_tags from the ->change_queue_type,
and when rejecting a tag message in a single driver, so keeping this
churn out of scsi_adjust_queue_depth is a clear win.

Now that the usage of scsi_adjust_queue_depth is more obvious we can
also remove all the trivial instances in ->slave_alloc or ->slave_configure
that just set it to the cmd_per_lun default.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>

Allow a driver to ask for block layer tags by setting .use_blk_tags in the
host template, in which case it will always see a valid value in
request->tag, similar to the behavior when using blk-mq.  This means even
SCSI "untagged" commands will now have a tag, which is especially useful
when using a host-wide tag map.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>

Unless we want to build a SPI tag message we should just check SCMD_TAGGED
instead of reverse engineering a tag type through the use of
scsi_populate_tag_msg.

Also rename the function to spi_populate_tag_msg, make it behave like the
other spi message helpers, and move it to the spi transport class.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NHannes Reinecke <hare@suse.de>

Most drivers use exactly the same implementation, so provide it as a
library function.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <bvanassche@acm.org>
Reviewed-by: NMike Christie <michaelc@cs.wisc.edu>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NHannes Reinecke <hare@suse.de>

Failing Device information are logged when IOA firmware detected these
illegal request such as IOA firmware doesn't support inquiry with page
code 2. The patch fixes the issue.
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Tested-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NChristoph Hellwig <hch@lst.de>

Add the appropriate definition and table entry for new hardware support.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This patch adds formatting error overlay 0x21 to improve debug capabilities.

[jejb: checkpatch fixes]
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

As result deprecation of MSI-X/MSI enablement functions
pci_enable_msix() and pci_enable_msi_block() all drivers
using these two interfaces need to be updated to use the
new pci_enable_msi_range() and pci_enable_msix_range()
interfaces.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

There is no need to call pci_disable_msi() or pci_disable_msix()
in case the call to pci_enable_msi() or pci_enable_msix() failed.
Signed-off-by: NAlexander Gordeev <agordeev@redhat.com>
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If, when the ipr driver loads, the adapter is in an EEH error state,
it will currently oops and not be able to recover, as it attempts
to access memory that has not yet been allocated. We've seen this
occur in some kexec scenarios. The following patch fixes the oops
and also allows the driver to recover from these probe time EEH errors.

[jejb: checkpatch fix]
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Add the appropriate definition and table entry for new hardware support.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This patch removes extended delay bit on GSCSI reads/writes ops, the
performance will be significanly better.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This was a debugging measure to toggle enabled/disabled
when testing. But for real production setups, it's not
safe to toggle this setting without either reloading
drivers of quiescing IO first. Neither of which the toggle
enforces.

Additionally, it makes drivers deal with the conditional
state.

Remove it completely. It's up to the driver whether iopoll
is enabled or not.
Signed-off-by: NJens Axboe <axboe@fb.com>

Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Some host adapters do not pass commands through to the target disk
directly. Instead they provide an emulated target which may or may not
accurately report its capabilities. In some cases the physical device
characteristics are reported even when the host adapter is processing
commands on the device's behalf. This can lead to adapter firmware hangs
or excessive I/O errors.

This patch disables WRITE SAME for devices connected to host adapters
that provide an emulated target. Driver writers can disable WRITE SAME
by setting the no_write_same flag in the host adapter template.

[jejb: fix up rejections due to eh_deadline patch]
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Cc: stable@kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Add the appropriate definitions and table entries for new adapter support.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The 'ctl' field of  the 'struct ata_taskfile' is not really dual purpose, i.e.
it is not intended  for storing the alternate status register (which is mapped
at the same address in the legacy IDE controllers) in the qc_fill_rtf() method.
No other 'libata' driver except 'drivers/scsi/ipr.c' stores the alternate status
register's value in the 'ctl' field of 'qc->result_tf', hence this driver should
not do this as well...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When enable lockdep, seeing "possible irq lock inversion dependency detected"
error. This patch fixes the issue.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Defined target_ids,array_ids and vsets_ids as unsigned long to avoid
target_destroy accessing memory after it was freed.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The 'ctl' field of  the 'struct ata_taskfile' is not really dual purpose, i.e.
it is not intended  for storing the alternate status register (which is mapped
at the same address in the legacy IDE controllers) in the qc_fill_rtf() method.
No other 'libata' driver except 'drivers/scsi/ipr.c' stores the alternate status
register's value in the 'ctl' field of 'qc->result_tf', hence this driver should
not do this as well...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NTejun Heo <tj@kernel.org>

Defined target_ids,array_ids and vsets_ids as unsigned long to avoid
target_destroy accessing memory after it was freed.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Driver passed the wrong IOADL address to IOA adapter. The patch
fixes the issue.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Add reset adapter after the 6th EEH errors in ipr driver. This triggers
the adapter reset via the PCI config space even when the slot is frozen.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Reinitialize resource queue prior to freeing resource entries to ensure they
are not referenced. This fixes an issue with target_destoy accessing memory
after it was freed.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The abort command issued by ipr_cancel_op() is being added to the wrong
HRRQ free queue after the command returns. Fix it by using the HRRQ
pointer in the ipr command struct itself.
Signed-off-by: NKleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Loading ipr modules failed(-22) with msi-x enabled adapter. In ipr_test_msi(),
We need to pass the first vector of msix vectors instead of using pdev->irq
to request_irq() when adapter enables msix feature.
Signed-off-by: NWen Xiong <wenxiong@linux.vnet.ibm.com>
Acked-by: NBrian King <brking@linux.vnet.ibm.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>