lpc32xx_pwm_config() is supposed to set duty_ns and period_ns,
it should not change PWM_ENABLE bit.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Tested-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

According to the LPC32x0 User Manual [1]:

For both PWM1 and PWM2 Control Registers:
BIT 31:
This bit gates the PWM_CLK signal and enables the external output pin
to the PWM_PIN_STATE logical level.

0 = PWM disabled. (Default)
1 = PWM enabled

So in lpc32xx_pwm_enable(), we should set PWM_ENABLE bit.
In lpc32xx_pwm_disable(), we should just clear PWM_ENABLE bit rather than
write 0 to the register which will also clear PWMx_RELOADV and PWMx_DUTY bits.

[1] http://www.nxp.com/documents/user_manual/UM10326.pdfSigned-off-by: NAxel Lin <axel.lin@ingics.com>
Tested-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

A few drivers already annotate this properly. Make the same change for
all other OF supporting drivers.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NAlexandre Pereira da Silva <aletes.xgr@gmail.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

PWM_ID_BASE() is not used after convert to PWM framework, remove it.
Also update driver_data field of struct platform_device_id accordingly.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NShiraz Hashim <shiraz.hashim@st.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Return proper error instead of 0 if twl6030_pwm_enable() fails.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

clk_enable/clk_disable maintain an enable_count, clk_prepare and clk_unprepare
also maintain a prepare_count. These APIs will do prepare/enable when the first
user calling these APIs, and do disable/unprepare when the corresponding counter
reach 0. Thus We don't need to maintain a clk_enabled counter here.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NEric Miao <eric.y.miao@gmail.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

We can test PWMF_ENABLED bit to know if pwm is enabled or not.
Thus remove enabled field from struct imx_chip.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Add missing .owner of struct pwm_ops. This prevents the module from being
removed from underneath its users.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Add missing .owner of struct pwm_ops. This prevents the module from being
removed from underneath its users.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Add missing .owner of struct pwm_ops. This prevents the module from being
removed from underneath its users.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Add missing .owner of struct pwm_ops. This prevents the module from being
removed from underneath its users.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

The logic to check return value of clk_enable() and clk_prepare() is reversed,
fix it.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Cc: stable@vger.kernel.org
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Both ehrpwm_pwm_save_context() and ehrpwm_pwm_restore_context() are only used in
this file, make them static.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Both ecap_pwm_save_context() and ecap_pwm_restore_context() are only used in
this file, make them static.
Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Signed-off-by: NAxel Lin <axel.lin@ingics.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Add EHRPWM and ECAP support build support for DAVINCI_DA8XX platforms.

Also, since DAVINCI platforms doesn't support TI-PWM-Subsystem module,
remove the select option for CONFIG_PWM_TIPWMSS.

Also, update CONFIG_PWM_TIPWMSS compiler directive appropriately in
pwm-tipwmss.h to fix the below compiler error upon removal of
CONFIG_PWM_TIPWMSS for DAVINCI platforms.

	drivers/pwm/pwm-tiecap.c: In function 'ecap_pwm_probe':
	drivers/pwm/pwm-tiecap.c:263:4: error: 'PWMSS_ECAPCLK_EN' undeclared
	(first use in this function)
	drivers/pwm/pwm-tiecap.c:263:4: note: each undeclared identifier
	is reported only once for each function it appears in
	drivers/pwm/pwm-tiecap.c:264:17: error: 'PWMSS_ECAPCLK_EN_ACK'
	undeclared (first use in this function)
	drivers/pwm/pwm-tiecap.c: In function 'ecap_pwm_remove':
	drivers/pwm/pwm-tiecap.c:291:49: error: 'PWMSS_ECAPCLK_STOP_REQ'
	undeclared (first use in this function)
	make[2]: *** [drivers/pwm/pwm-tiecap.o] Error 1
	make[1]: *** [drivers/pwm] Error 2
	make: *** [drivers] Error 2
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

This patch adds CONFIG_PM_SLEEP to suspend/resume functions to fix
the following build warning when CONFIG_PM_SLEEP is not selected.

drivers/pwm/pwm-tiehrpwm.c:562:12: warning: 'ehrpwm_pwm_suspend' defined but not used [-Wunused-function]
drivers/pwm/pwm-tiehrpwm.c:580:12: warning: 'ehrpwm_pwm_resume' defined but not used [-Wunused-function
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

This patch adds CONFIG_PM_SLEEP to suspend/resume functions to fix
the following build warning when CONFIG_PM_SLEEP is not selected.

drivers/pwm/pwm-tipwmss.c:104:12: warning: 'pwmss_suspend' defined but not used [-Wunused-function]
drivers/pwm/pwm-tipwmss.c:113:12: warning: 'pwmss_resume' defined but not used [-Wunused-function]
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

This patch adds CONFIG_PM_SLEEP to suspend/resume functions to fix
the following build warning when CONFIG_PM_SLEEP is not selected.

drivers/pwm/pwm-tiecap.c:314:12: warning: 'ecap_pwm_suspend' defined but not used [-Wunused-function]
drivers/pwm/pwm-tiecap.c:328:12: warning: 'ecap_pwm_resume' defined but not used [-Wunused-function]
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Instead of using legacy suspend/resume methods, using newer dev_pm_ops
structure allows better control over power management.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Use devm_kzalloc() to make cleanup paths more simple.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Always use to_twl() for converting into private data instead of
container_of().
Signed-off-by: NJohannes Thumshirn <morbidrsa@gmail.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Tegra only supports, and always enables, device tree. Remove all ifdefs
for DT support from the driver.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

When booted with DT users can use devm version of of_pwm_get() to benefit
from automatic resource release.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

Allow client driver to use of_pwm_get() to get the PWM they need. This
is needed for drivers which handle more than one PWM separately, like
leds-pwm driver, which have:

pwmleds {
	compatible = "pwm-leds";
	kpad {
		label = "omap4::keypad";
		pwms = <&twl_pwm 0 7812500>;
		max-brightness = <127>;
	};

	charging {
		label = "omap4:green:chrg";
		pwms = <&twl_pwmled 0 7812500>;
		max-brightness = <255>;
	};
};

in the dts files.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: NThierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: NBryan Wu <cooloney@gmail.com>

When building a driver as a module, these functions need to be exported
for linking to succeed.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

PWM is now consistently spelled in all uppercase letters. For the Atmel
driver the entry now also mentions Atmel to make it easier to find.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Calls to PWM drivers connected through I2C can sleep.
Use the new can_sleep property.
Acked-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Calls to some external PWM chips can sleep. To help users,
add pwm_can_sleep() API.

Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NFlorian Vaussard <florian.vaussard@epfl.ch>
Reviewed-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Convert all uses of devm_request_and_ioremap() to the newly introduced
devm_ioremap_resource() which provides more consistent error handling.
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In low power modes of AM33XX platforms, peripherals power is cut off.
This patch supports low power sleep transition support for ECAP driver.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

In low power modes of AM33XX platforms, peripherals power is cut off.
This patch supports low power sleep transition support for EHRPWM
driver.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

The clock framework has changed and it's now better to invoke
clock_prepare_enable() and clk_disable_unprepare() rather than the
legacy clk_enable() and clk_disable() calls. This patch converts the
pwm-tiehrpwm driver to the new framework.
Signed-off-by: NPhilip Avinash <avinashphilip@ti.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Add support to set polarity on PWM devices, allowing for inverted
duty cycles.

Also update the binding document to #pwm-cells = <3> to allow
passing the flags from devicetree.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

Correct operation for register writes is to perform a busy-wait
after writing the register. Currently the busy wait it performed
before, meaning subsequent register writes to bitfields may occur
before the previous field has been updated.

Also, all registers are defined as 32-bit read/write. Change
pwm_busy_wait() to use readl rather than readb.

Improve readability of code with defines for registers and bitfields.
Signed-off-by: NTony Prisk <linux@prisktech.co.nz>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

This patch adds a PWM driver based on Atmel Timer Counter Block. The
Timer Counter Block is used in Waveform generator mode.

A Timer Counter Block provides up to 6 PWM devices grouped by 2:
* group 0 = PWM 0 and 1
* group 1 = PWM 2 and 3
* group 2 = PMW 4 and 5

PWM devices in a given group must be configured with the same period
value. If a PWM device in a group tries to change the period value and
the other device is already configured with a different value an error
will be returned.

This driver requires device tree support. The Timer Counter Block number
used to create a PWM chip is given by the tc-block field in an
"atmel,tcb-pwm" compatible node.

This patch was tested on kizbox board (at91sam9g20 SoC) with pwm-leds.
Signed-off-by: NBoris BREZILLON <linux-arm@overkiz.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>

The s3c->pwm_id is used to calculate offset of related register.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NThierry Reding <thierry.reding@avionic-design.de>