The queue ID should never be 512 either, so correct the check
to be >= instead of just >.

Fixes: 310181ec ("iwlwifi: move to TVQM mode")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Since we exit if buf->num_stored is 0, there's no need to
check it again later.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When sending a Tx Command with a Tx packet, we allocate the
Tx command separately from the payload of the packet.
The WiFi MAC header is then copied into the buffer that was
allocated for the Tx Command. This means that this buffer
needs to be big enough to contain both. This is why it is
allocated with iwl_trans_alloc_tx_cmd which returns a
pointer to a newly allocated not zeroed struct
iwl_device_cmd.

The Tx command has a few bit fields and hence it needs to
be zeroed, but all the rest of the buffer doesn't need to
be zeroed since it will either be memcopy'ed with the MAC
header, or not even sent to the device.
This means that we don't need to zero all the
iwl_device_cmd structure, but rather only the size of
the iwl_tx_cmd structure.

Since sizeof(iwl_tx_cmd) - sizeof(iwl_tx_cmd) is about
260 bytes, this can avoid touching 4 cache lines for each
packet.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Install GTKs on AP side for new TX API.
Don't add IV space, it's added by the HW.

While at that fix GCMP abnd GCMP-256 GTK installation
which work similarly to the new TX API.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

If FW isn't alive, trying to collect debug data will
result in errors both in driver and in the collected
data, so just warn and leave the collecting function
in this case.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Contrary to what some of the comments say, if rfkill was
asserted the transport will return -ERFKILL instead of
success, if CMD_WANT_SKB was set, so it's not necessary
to check cmd.resp_pkt for being NULL if the return code
was success.

Validate that this is true in iwl_trans_send_cmd().

Most of the other code modifications were done with the
following spatch:
    @@
    struct iwl_host_cmd cmd;
    identifier pkt;
    @@
    <...
    (
    pkt = cmd.resp_pkt;
    ...
    -if (!pkt) { ... }
    |
    pkt = cmd.resp_pkt;
    ...
    -if (WARN_ON(!pkt)) { ... }
    |
    -if (!cmd.resp_pkt) { ... }
    )
    ...>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In DQA mode, there is no need to wait for the TXQ to
clear out after getting a DELBA, since traffic can
continue running on the queue.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we removed dev_cmd_headroom, the check for dev_cmd_ptr == NULL
became unnecessary, since we just return dev_cmd_ptr anyway.  Cleanup
the function to avoid useless code.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Bump the maximum accepted firmware API number for devices in the 8000,
9000 and A000 families.
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The include in the deleted file are included in the fw-api.h file.
Which caused a cycle include in the dependencies.
Signed-off-by: NMordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The firmware no longer uses this command group, so remove it from
the driver as well.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Link from the TX_CMD enum value to the TX command structs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Document which structures are used with the command for
the A000 hardware flavour.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In order to more clearly document which parts of this file
are firmware API and which are something else, split the
firmware API into a separate file to include here.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The kernel-doc here is on an enum, so don't tag it as struct
but correctly as enum instead, preventing an error.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Clear the firmware running bit before flushing the FW (error) dump
work, because otherwise debugfs isn't blocked (previous patch) and
can cause a new work to be scheduled, which will then run after we
actually shut down the device, wreaking havoc. Clearing it ensures
that debugfs can't interfere anymore, and we can safely cancel or
flush the work struct.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Convert ucode_loaded to a status bit called FIRMWARE_RUNNING.
This will make it easier to clear this earlier, to avoid any
spurious accesses while shutting down, for example through
debugfs.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This will help refactor this later.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

There's no need to refer to system_wq directly, use the provided
wrapper schedule_delayed_work().

Made with the following spatch:
    @@
    expression E,F;
    @@
    -queue_delayed_work(system_wq, E, F);
    +schedule_delayed_work(E, F);
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Protect various debugfs files that need to communicate with the
firmware from being used when the firmware isn't running.

Some will just reject getting written to, while others that store
some state will simply store it and not apply it immediately.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Apart from the current list of PRPH that can't be
collected in A000 HW, the rest of the debug dump
data the driver collects is valid, so there is no
need to disable collection only because of this.

Disable PRPH collecting in A000 HW, and allow
collecting the rest of the debug data.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

FH in A000 HW are placed in a different location,
and need to be read as prph, rather than direct.
Support A000 dumping as well as legacy.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add two new device families to differentiate them from 8000.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In case an assert happens on init flow, the current
driver powers down the NIC, except if iwlmvm modparam
init_dbg=1, and only on very specific flows.

Extend this capability to cover most failure cases
by keeping track of what init configurations have been
completed. This way, we can allow NOT powering down
the NIC, while making sure that when the driver is
removed we don't try to free resources that haven't
been allocated. (This can result in a kernel panic.)
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Due to NAN FW API change, add TLV in order to distiguish between the
2 API versions
Signed-off-by: NBeni Lev <beni.lev@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Use transport configuration to determine DBGC support
instead of relying on device family.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We don't have any 8000 B-step right now, and there is no
firmware loading code for them anyway.
Further more, 9000 B-step devices will hit those code paths.
Remove code that was introduced only for 8000 B-step.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

NVM code is tightly coupled with 8000 family, while
it really refers to extended NVM format introduced
back then. Separate it to a configuration dependent
boolean, and rename defines accordingly.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This is essentially the same code as gen1, except that it uses
gen2 functions and SW checksum is not included.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Document the structures used in RX and link them to the command ID.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Enable offload assist for AMSDU when the AMSDU present flag is set.

Fixes: a830baba9c2e ("iwlwifi: mvm: support new TX API")
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Sending host command with CMD_WANT_SKB flag demands the release of the
response buffer with iwl_free_resp function.
The patch adds the memory release in all the relevant places
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In a previous commit, we removed support for API versions earlier than
22 for these NICs.  By mistake, the *_UCODE_API_MIN definitions were
set to 17.  Fix that.

Fixes: 4b87e5af ("iwlwifi: remove support for fw older than -17 and -22")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Clear the struct so that all reserved fields are zero when we
send the struct down to the device.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The iwl_mvm_remove_sta_key() function handles removing a key when the
sta doesn't exist anymore.  Mistakenly, this was changed to return an
error while fixing another bug.

If the mvm_sta doesn't exist, we continue normally, but just don't try
to remove the igtk key.

Fixes: cd4d23c1 ("iwlwifi: mvm: Fix removal of IGTK")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We only need to handle d0i3 entry and exit during suspend resume if
system_pm is set to IWL_PLAT_PM_MODE_D0I3, otherwise d0i3 entry
failures will cause suspend to fail.

This fixes https://bugzilla.kernel.org/show_bug.cgi?id=194791Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When we want to stop the recording of the firmware debug
and restart it later without reloading the firmware we
don't need to resend the configuration that comes with
host commands.
Sending those commands confused the hardware and led to
an NMI 0x66.

Change the flow as following:
* read the relevant registers (DBGC_IN_SAMPLE, DBGC_OUT_CTRL)
* clear those registers
* wait for the hardware to complete its write to the buffer
* get the data
* restore the value of those registers (to restart the
  recording)

For early start (where the configuration is already
compiled in the firmware), we don't need to set those
registers after the firmware has been loaded, but only
when we want to restart the recording without having
restarted the firmware.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The ucode_loaded check should be under the mutex, since it can
otherwise change state after we looked at it and before we got
the mutex. Fix that.

Fixes: 5c89e7bc ("iwlwifi: mvm: add registration to cooling device")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Allow working IBSS also when working in DQA mode.
This is done by setting it to treat the queues the
same as a BSS AP treats the queues.

Fixes: 7948b873 ("iwlwifi: mvm: enable dynamic queue allocation mode")
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>