Patch "firewire: fw-sbp2: fix NULL pointer deref. in scsi_remove_device"
had the unintended effect that firewire-sbp2 could not be unloaded
anymore until all SBP-2 devices were unplugged.

We now fix the NULL pointer bug by reacquiring a reference to the sdev
instead of holding a reference to the sdev (and to the module) all the
time.
Signed-off-by: NStefan Richter <stefanr@s5r6.in-berlin.de>
Tested-by: NJarod Wilson <jwilson@redhat.com>

Interrupts must be disabled if using kmap_atomic(KM_IRQ0), but that was
not the case in a few code paths coming directly from ATA driver
interrupt handlers (which use spin_lock rather than spin_lock_irqsave).
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

Fix hpet_(un)register_irq_handler() for when CONFIG_HPET_EMULATE_RTC=n.  They
are provided macros that substitute value 0, but if they are called as
functions and the return value isn't checked, the following warnings appear:

	drivers/char/rtc.c: In function `rtc_init':
	drivers/char/rtc.c:1063: warning: statement with no effect
	drivers/char/rtc.c: In function `rtc_exit':
	drivers/char/rtc.c:1157: warning: statement with no effect
Signed-off-by: NDavid Howells <dhowells@redhat.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

http://blackfin.uclinux.org/gf/project/uclinux-dist/tracker/?action=TrackerItemEdit&tracker_item_id=3910Signed-off-by: NSonic Zhang <sonic.zhang@analog.com>
Signed-off-by: NBryan Wu <cooloney@kernel.org>

This patch adds support (including ATAPI DMA) for HT1100 (aka BCM11000) SATA controller.
Signed-off-by: NAnantha Subramanyam <ananth@broadcom.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Several endianity corrections in start_xmit()

Fixed TSO bug where packets were missing the TCP flags.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Limit traffic through an internal queue to prevent overflow.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fixed locking between fastpath and slowpath operations.

Corrected order of traffic disabling to prevent race when going down
under traffic.

- first have the microcode drop all incoming packets
- then do the slowpath stuff
- only then reset the MAC

Got rid of in_reset_task.

Remove_one() and friends would deference a null pointer if init_one
failed.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some of the HW attentions, used to indicate an error were not properly
acked.

This will cause the driver to endlessly receive interrupts when such
an error happens.

Had to break the code into smaller chunks because it got too nested.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Errata A0.158 workaround. 

Running in INT#A mode after running with MSI-X fails due to a PCI core
bug.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Errors were summed improperly, some stats were missing.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The configuration of RX filtering needed the following corrections:

Drop flags need to be set per Rx queue.

Have to tell the microcode to collect drop stats, and properly wait
for them to complete when going down.

Sometimes we failed to detect proper completion due to a logical error
in the wait loop.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Properly protect PHY access between two devices on the same board with
a HW lock.

Use GPIO to clear all previous configurations before changing link
parameters.

Shut down the external PHY in case of fan failure.

Reducing the MDC/MDIO clock to 2.5MHz due to problems with some
devices.

Resolve the flow control response according to autoneg with external
PHY.

Unmasking all PHY interrupts in single write to prevent a race in the
interrupts order.

LASI indication fixes to work with peculiarities of PHYs.

Disable MAC RX to avoid a HW bug when closing the MAC under traffic.

Disable parallel detection on HiGig due to HW limitation.

Updating the shared memory structure to work with the current
bootcode.
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Correct PCI-E info printed by init_one()
In one case it failed to free the netdev. 
Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NEliezer Tamir <eliezert@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch the SSB PCI core driver to the new SPROM data structure now that
the old one has been removed.
Signed-off-by: NAurelien Jarno <aurelien@aurel32.net>
Acked-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This may happen e.g. when the ssb is statically enables by the b44 driver,
and the b43 pci-ssb bridge is enbled by the b43/b43legacy drivers, or the
b43/b43legacy drivers are built statically.
Signed-off-by: NAlexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The bridge code was unnecessary enabled by the b44
driver, but it prevents the bcm43xx driver from
being loaded, as the bridge claims the same pci ids.

Now we enable the birdge only if the b43{legacy}
drivers are selected.
Signed-off-by: NAlexey Zaytsev <alexey.zaytsev@gmail.com>
Acked-by: NLarry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The libertas driver exports a number of symbols with no in-tree users;
remove these unused exports.  lbs_reset_device() is completely unused, with
no callers at all, so remove the function completely.

A couple of these unused exported symbols are static, which causes the
following build error on ia64 with gcc 4.2.3:

    drivers/net/wireless/libertas/main.c:1375: error: __ksymtab_lbs_remove_mesh causes a section type conflict
    drivers/net/wireless/libertas/main.c:1354: error: __ksymtab_lbs_add_mesh causes a section type conflict
Signed-off-by: NRoland Dreier <rolandd@cisco.com>
Acked-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

rt2x00lib_reset_link_tuner() can be called from within
the link tuner itself. This means that it should
_not_ call rt2x00lib_stop_link_tuner() since that will
cause the thread to hang.

Reorder the things that should be done during a
link tuner reset and during a link tuner start.

Also make antenna tuning the last step of the link
tuner since it could possibly reset some statistical
information which we need for average calculation.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When rssi_a > rssi_b is true and the current antenna
was already antenna A, then rt2x00 incorrectly jumped
to antenna B.

Also don't configure the antenna when there has been
no change in the antenna setup.
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This adds 2 new states which both are used to toggle
the RX. These new states are required for usage
inside the link tuner thread, because the normal
RX toggling will stop the link tuner thread.
While it is possible that the link tuner thread itself
is the caller of the RX toggle (when using software
antenna diversity).
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix 2 issues in antenna diversity selection.

1) the following statement will always return true.
	if ((rssi_curr - rssi_old) > -5 || (rssi_curr - rssi_old) < 5)
It is cleaner to check if the absolute value is smaller then 5.

2) Only enable software diversity when default antenna setup
indicates support for it. Don't select it when the hardware
does not indicate support for it...
Signed-off-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

|   CC      drivers/net/ps3_gelic_wireless.o
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c: In function 'gelic_wl_setup_netdev_ops':
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2660: error: 'struct net_device' has no member named 'wireless_data'
| /home/bigeasy/git/linux-2.6/drivers/net/ps3_gelic_wireless.c:2661: error: 'struct net_device' has no member named 'wireless_handlers'
| make[3]: *** [drivers/net/ps3_gelic_wireless.o] Error 1
| make[2]: *** [drivers/net] Error 2
| make[1]: *** [drivers] Error 2
| make[1]: *** Waiting for unfinished jobs....
| make: *** [sub-make] Error 2
Signed-off-by: NSebastian Siewior <sebastian@breakpoint.cc>
Acked-by: NMasakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Link the net_device structure of the wireless part to the
corresponding device structure.

Without this, the sysfs node for this net_device would not have
'device' link.
Signed-off-by: NMasakazu Mokuno <mokuno@sm.sony.co.jp>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is obviously wrong to use an enum in a little endian struct,
and those other enums should be declared differently.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Acked-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It is used in connector.c only, so make it static.
Signed-off-by: NLi Zefan <lizf@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the macvlan release I had at least 5 users asking how to configure
it since the old userspace tool doesn't work with the version in the
kernel. Add a pointer to the Kconfig help.
Signed-off-by: NPatrick McHardy <kaber@trash.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Interrupt moderation low threshold value was incorrectly triggering,
indicating that the threshold should be lowered.

The impact was the timer was likely to become 40usecs and get stuck
there.  The biggest side effect was too many interrupts and nonoptimal
performance.
Signed-off-by: NJohn Lacombe <jlacombe@neteffect.com>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

With commit ef19454b ("[LIB] crc32c: Keep intermediate crc state in
cpu order"), the behavior of crc32c changes on big-endian platforms.

Our algorithm expects the previous behavior; otherwise we have RDMA
connection establishment failure on big-endian platforms like powerpc.
Apply cpu_to_le32() to value returned by crc32c() to get the previous
behavior.
Signed-off-by: NFaisal Latif <flatif@neteffect.com>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix use-after-free spotted by Coverity checker flagged by Adrian Bunk.
Signed-off-by: NFaisal Latif <flatif@neteffect.com>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Just delete the debugging statement so we don't use cqp_request after
freeing it.  Adrian Bunk flagged this use-after-free issue spotted by
the Coverity checker.
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix a check-after-use spotted by the Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

Fix a memory leak spotted by the Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@kernel.org>
Signed-off-by: NGlenn Streiff <gstreiff@neteffect.com>
Signed-off-by: NRoland Dreier <rolandd@cisco.com>

- ide-dma.c is not a separate module

- ide-dma.c is not PCI specific anymore

- DMA is enabled by default nowadays

- link for Intel Zappa BIOS is dead

etc.

v2:
* Some comments should be preserved. (Noticed by Mark Lord)

Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: NBorislav Petkov <petkovbb@gmail.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>

drivers/ide/ide.c:801:18: warning: symbol 'flags' shadows an earlier one
drivers/ide/ide.c:732:16: originally declared here

Also fix some whitespace damage while at it.
Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>