Also, create and use an rt6_bind_neighbour() in net/ipv6/route.c to
consolidate some common logic.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to perform a proper universal hash on a vector of integers,
we have to use different universal hashes on each vector element.

Which means we need 4 different hash randoms for ipv6.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check setsockopt arguments to avoid overflows and return -EINVAL for
too large arguments.
Signed-off-by: NXi Wang <xi.wang@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit be639ac6 ("NET: AX.25: Check ioctl arguments to avoid overflows
further down the road") rejects very large arguments, but doesn't
completely fix overflows on 64-bit systems.  Consider the AX25_T2 case.

	int opt;
	...
	if (opt < 1 || opt > ULONG_MAX / HZ) {
		res = -EINVAL;
		break;
	}
	ax25->t2 = opt * HZ;

The 32-bit multiplication opt * HZ would overflow before being assigned
to 64-bit ax25->t2.  This patch changes "opt" to unsigned long.
Signed-off-by: NXi Wang <xi.wang@gmail.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When testing L2TP support, I discovered that the l2tp module is not autoloaded
as are other netlink interfaces. There is because of lack of hook in genetlink to call
request_module and load the module.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The route we have here is for the address being added to the interface,
ie. for input packet processing.

Therefore using that route to determine whether an output nexthop gateway
is known and resolved doesn't make any sense.

So, simply remove this test, it never triggered anyways.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Acked-By: NNeil Horman <nhorman@tuxdriver.com>

On extensive NFS boots on a mx6qsabrelite board it was noted that "FEC: MDIO read timeout" were occuring,
which caused failure on loading the FEC driver.

The original FEC_MII_TIMEOUT was set to 1 ms, which is too low when passed to the usecs_to_jiffies macro.

On ARM one jiffy is 10ms, so use a timeout of 30ms, which corresponds to 3 jiffies.

After running extensive NFS boots, the MDIO timeouts do not occur anymore with this change.
Signed-off-by: NRogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using /proc/net/nf_conntrack has been deprecated in favour of the
conntrack(8) tool.
Signed-off-by: NJan Engelhardt <jengelh@medozas.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

One simplification of an if clause.
Signed-off-by: NJan Engelhardt <jengelh@medozas.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

References: http://www.spinics.net/lists/netfilter-devel/msg18875.html

Augment xt_ecn by facilities to match on IPv6 packets' DSCP/TOS field
similar to how it is already done for the IPv4 packet field.
Signed-off-by: NJan Engelhardt <jengelh@medozas.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Use the new macro and struct names in xt_ecn.h, and put the old
definitions into a definition-forwarding ipt_ecn.h.
Signed-off-by: NJan Engelhardt <jengelh@medozas.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

Prepare the ECN match for augmentation by an IPv6 counterpart. Since
no symbol dependencies to ipv6.ko are added, having a single ecn match
module is the more so welcome.
Signed-off-by: NJan Engelhardt <jengelh@medozas.de>
Signed-off-by: NPablo Neira Ayuso <pablo@netfilter.org>

SGI IP32 (O2)'s ethernet driver (meth) lacks a set_rx_mode function, which
prevents IPv6 from working completely because any ICMPv6 neighbor
solicitation requests aren't picked up by the driver.  So the machine can
ping out and connect to other systems, but other systems will have a very
hard time connecting to the O2.
Signed-off-by: NJoshua Kinard <kumba@gentoo.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix allyesconfig build on architectures without IOMEM:

drivers/net/ethernet/calxeda/xgmac.c:1800:2:
  error: implicit declaration of function 'iounmap' [-Werror=implicit-function-declaration]
Signed-off-by: NHeiko Carstens <heiko.carstens@de.ibm.com>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Migrates the buf_seqno() helper routine from broadcast link level to
unicast link level so that it can be used both types of TIPC links.
This is a cosmetic change only, and does not affect the operation of TIPC.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Adds checks to TIPC's broadcast link so that it ignores any
acknowledgement message containing a sequence number that does not
correspond to an unacknowledged message currently in the broadcast
link's transmit queue.

This change prevents the broadcast link from becoming stalled if a
newly booted node receives stale broadcast link acknowledgement
information from another node that has not yet fully synchronized
its end of the broadcast link to reflect the current state of the
new node's end.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Adds code to release any unsent broadcast messages in the broadcast link
transmit queue if TIPC loses contact with its only neighboring node.
Previously, a broadcast link that was in the congested state would hold
on to the unsent messages, even though the messages were now undeliverable.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

The two broadcast link statistics fields that are used to derive the
average length of that link's transmit queue are now updated only after
a successful attempt to send a broadcast message, since there is no need
to update these values when an unsuccessful send attempt leaves the
queue unchanged.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Adds a check to detect when an attempt is made to send a message
via the broadcast link and no neighboring nodes are currently available
to receive it. Rather than wasting effort passing the message to the
broadcast link and broadcast bearer, who will only throw it away,
TIPC now frees the message immediately and reports success (i.e. the
message has been delivered to all available destinations).
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Fixes oversight that allowed broadcast link node map to be updated without
first taking the broadcast link spinlock that protects the map. As part
of this fix the node map has been incorporated into the broadcast link
structure to make the need for such protection more evident.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Creates global variables to hold the broadcast link's pseudo-bearer and
pseudo-link structures, rather than allocating them dynamically. There
is only a single instance of each structure, and changing over to static
allocation allows elimination of code to handle the cases where dynamic
allocation was unsuccessful.

The memset in the teardown code may look like they aren't used, but
the same teardown code is run when there is a non-fatal error at
init-time, so that stale data isn't present when the user fixes the
cause of the soft error.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Gets rid of an unnecessary check in the routine that updates the port id
of a node's name publications when the node is assigned a network address,
since the routine is only invoked if the new address is different from
the existing one.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Modifies TIPC's module unloading logic to switch itself into "single
node" mode before starting to terminate networking support. This helps
to ensure that no operations that require TIPC to be in "networking"
mode can initiate once unloading starts.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Gets rid of two pointless operations that zero out the array used to
record information about TIPC's Ethernet bearers. There is no need to
initialize the array on start up since it is a global variable that is
already zero'd out, and there is no need to zero it out on exit because
the array is never referenced again.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Modifies Ethernet bearer disable logic to break the association between
the bearer and its device driver at the time the bearer is disabled,
rather than when the TIPC module is unloaded. This allows the array
entry used by the disabled bearer to be re-used if the same bearer (or
a different one) is subsequently enabled.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Change TIPC's shutdown code to deactivate generic networking support
before terminating Ethernet media support. The deactivation of generic
networking support causes all existing bearers to be destroyed, meaning
the Ethernet media termination routine no longer has to bother marking
them as unavailable.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Comment-only change to better explain why TIPC's configuration lock is
temporarily released while activating support for network interfaces,
and why the existing activation code doesn't require rework.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Permits run-time alteration of default link settings on a per-media
and per-bearer basis, in addition to the existing per-link basis.
The following syntax can now be used:

    tipc-config -lt=<link-name|bearer-name|media-name>/<tolerance>
    tipc-config -lp=<link-name|bearer-name|media-name>/<priority>
    tipc-config -lw=<link-name|bearer-name|media-name>/<window>

Note that changes to the default settings for a given media type has
no effect on the default settings used by existing bearers. Similarly,
changes to default bearer settings has no effect on existing link
endpoints that utilize that interface.

Thanks to Florian Westphal <fw@strlen.de> for his contributions to
the development of this enhancement.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Adds a check to ensure that TIPC ignores an incoming neighbor discovery
message that specifies an invalid media address as its source. The check
ensures that the source address is a valid, non-broadcast address that
could legally be used by a neighboring link endpoint.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Reworks TIPC's media address data structure and associated processing
routines to transfer all media-specific details of address conversion
to the associated TIPC media adaptation code. TIPC's generic bearer code
now only needs to know which media type an address is associated with
and whether or not it is a broadcast address, and totally ignores the
"value" field that contains the actual media-specific addressing info.

These changes eliminate the need for a number of endianness conversion
operations and will make it easier for TIPC to support new media types
in the future.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Enhances TIPC's Ethernet media support to provide 3 new address conversion
routines, which allow TIPC to interpret an address that is in string form
and to convert an address to and from the 20 byte format used in TIPC's
neighbor discovery messages.

These routines are pre-requisites to a follow on commit that hides all
media-specific addressing details from TIPC's generic bearer code.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Enhances conversion of a media address to printable form so that an
unconvertable address will be displayed as a string of hex digits,
rather than not being displayed at all. (Also removes a pointless check
for the existence of the media-specific address conversion routine,
since the routine is not optional.)
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Simplifies error handling performed during media registration, since
TIPC no longer supports the dynamic addition of new media types that
are potentially error-prone. These simplifications include the following:

1) No longer check for premature registration of a new media type.
2) No longer check for negative link priority values (which was pointless
   since such values are unsigned, and could cause a compiler warning).
3) No longer generate a warning describing the exact cause of any
   registration failure (just warns that overall registration failed).
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Changes TIPC's list of registered media types from an array of media
structures to an array of pointers to media structures. This eliminates
the need to copy of the contents of the structure passed in during media
registration.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Streamlines the detection of an attempt to register a TIPC media structure
using an already registered name or type identifier. The revised logic now
reuses an existing routine to detect an existing name and no longer
unnecessarily manipulates the media type counter during an unsuccessful
registration attempt.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Speeds up the registration of TIPC media types by passing in a structure
containing the required information, rather than by passing in the various
fields describing the media type individually.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

Permits a Linux container to use TIPC sockets even when it has its own
network namespace defined by removing the check that prohibits such use.
This makes it possible for users who wish to isolate their container
network traffic from normal network traffic to utilize TIPC.
Signed-off-by: NAllan Stephens <allan.stephens@windriver.com>
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

v2, based on Jay's review.

I kept the 'link must be up' part, because this is enforced in the code.
Signed-off-by: NNicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

RDBG() wasn't even used, and the messages printed by RT6_DEBUG() were
far from useful.  Just get rid of all this stuff, we can replace it
with something more suitable if we want.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>