Next card access will be always
error if it didn't clear error status
Tested-by: NNguyen Xuan Nui <nx-nui@jinso.co.jp>
Tested-by: NHiep Cao Minh <cm-hiep@jinso.co.jp>
Signed-off-by: NShinobu Uehara <shinobu.uehara.xc@renesas.com>
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>

These library functions aren't used and nor needed, let's remove them.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>

To give the option for tmio hosts to use the runtime PM callbacks for
CONFIG_PM_SLEEP as well as CONFIG_PM_RUNTIME, move them to CONFIG_PM.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>

To make sure we don't receive any spurious IRQs while we are inactive,
mask the IRQs from within the ->runtime_suspend() callback.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Add clock gating control as a part of the tmio library functions for
runtime PM.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>

An internal power state machine were beeing used to keep ->probe() and
->set_ios() in sync. Especially for handling specific scenarios while
using CONFIG_MMC_CLKGATE. Moreover dependency to CONFIG_MMC_CLKGATE
existed to handle runtime PM properly, which we moves away from here.

By removing the state machine and instead make ->set_ios() rely on the
information provided through the function's in-parameters, the code
becomes significantly simplier.

Additonally as a part of this rework we prepares for making the runtime
PM callbacks responsible of clock gating.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Move code for bus_width modification, out of the ->set_ios() callback
and into a separate function, to simplify code.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Use runtime PM to keep the host active during I/O operations and other
requests which requires the tmio hardware to be powered.

Additionally make use of the runtime PM autosuspend feature with a
default timeout of 50 ms.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>

The host must be kept active to be able to serve SDIO IRQs, thus let's
prevent it from going inactive while SDIO IRQ is enabled.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGeert Uytterhoeven <geert+renesas@glider.be>

Since the users of the exported PM functions are now using the modern
PM ops macros, we can convert to the proper corresponding PM configs.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <chris@printf.net>

The accessibility checking method to the higher register was added by
69d1fe18 (mmc: tmio: only access registers above 0xff, if available)
But, it doesn't care 32bit register.  It is impossible to calculate it
from the resource size, since there is 16/32 bit register IP (e.g. VERSION
is located on 0xe2 if 16bit register, but it is located on 0x1c4 if 32bit
register).

This patch adds new TMIO_MMC_HAVE_HIGH_REG flags, tmio_mmc driver has it,
and sh_mobile_sdhi doesn't have it today.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

.bus_shift is used to 16/32bit register access offset calculation on
tmio driver.  tmio_mmc_xxx is used from Toshiba/Renesas now, but this
bus_shift value depends on HW IP.  This patch moves .bus_shift to
tmio_mmc_data member and sets it on each driver.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Current tmio driver tries to use default ocr_avail if 1) it couldn't
find regulator and 2) if platform data doesn't have ocr_mask.
But, there is no guarantee that regulator driver probe is faster than
TMIO driver probe.  TMIO driver will not use regulator in such case.

By this patch, TMIO driver returns -EPROBE_DEFER if it couldn't find
regulator and if platform doesn't have ocr_mask.  Because, there is a
possibility that regulator has not been probed, but the user expects it.

This patch changes tmio_mmc_host_probe() behavior, but there is no user
who has conflict.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

02cb3221 ("mmc: tmio: support caps2 flags") added caps2 support on
tmio, but it overwrites mmc_of_parse() settings.  This patch fixes it.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Acked-by: NLaurent <laurent.pinchart@ideasonboard.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.

This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.

Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This reverts commit 3af9d15c, which
causes a build failure:

drivers/mfd/asic3.c:724:2: error: unknown field 'set_pwr' specified in initializer

The .set_pwr() callback isn't used anymore as all platforms register
GPIO-controlled regulators. Remove it.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

All platforms pass the CD GPIO number to the driver in the .cd_gpio
field. The .get_cd() callback isn't used anymore, remove it
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add a debounce parameter to the mmc_gpio_request_cd() function that
enables GPIO debouncing when set to a non-zero value. This can be used
by MMC host drivers to enable debouncing on the card detect signal.
Signed-off-by: NLaurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch fixes a compiler warning:

drivers/mmc/host/tmio_mmc_pio.c: In function 'tmio_mmc_power_on':
drivers/mmc/host/tmio_mmc_pio.c:798:19: warning: ignoring return value of
'regulator_enable', declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NSimon Baatz <gmbnomis@gmail.com>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

This fixes two reported problems:
1. after a system resume the controller isn't functioning until a command
   runs on a timeout and a controller reset is performed.
2. if a card is ejected during a running write operation, its re-insertion
   isn't detected.
Reported-by: NNguyen Viet Dung <nv-dung@jinso.co.jp>
Reported-by: NNguyen Hong Ky <nh-ky@jinso.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Tested-by: NNguyen Viet Dung <nv-dung@jinso.co.jp>
Tested-by: NNguyen Hong Ky <nh-ky@jinso.co.jp>
Signed-off-by: NChris Ball <cjb@laptop.org>

With MMC clock gating enabled the MMC core currently calls MMC host driver's
.set_ios() method with .power_mode == MMC_POWER_ON and the clock value set
either to 0 or to the target rate. The tmio MMC driver then wrongly
translates the latter calls to card slot power-on requests, even when the
slot already was on. This patch fixes the driver to avoid needlessly
incrementing power-supplying regulator's use count.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Tested-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

When resuming, the tmio_mmc_host_resume() function is run when the
controller might still be powered down. Issuing a reset command to it at
that time has no effect. This patch postpones resetting the controller
until the first powering-up .set_ios() call.
Reported-by: NNguyen Viet Dung <nv-dung@jinso.co.jp>
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some SD/MMC interfaces use 2 power regulators: one to power the card itself
(Vcc) and another one to pull signal lines up (VccQ). In case of eMMC and
UHS SD cards the regulators also have to be configured to supply different
voltages. The preferred order of turning supply power on and off is to
turn Vcc first on and last off.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add parsing of common and driver-specific DT bindings to the tmio-mmc
MMC host driver and the sh_mobile_sdhi interface layer.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

tmio-mmc platform flags can be set by various means, including caller
drivers and device-tree bindings, therefore it is better to only check
them in the tmio-mmc driver proper, not in caller drivers themselves.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Since slot-gpio uses devm_* managed functions in mmc_gpio_request_cd()
now, we can remove those mmc_gpio_free_cd() call from host drivers'
.probe() error path and .remove().
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Since slot-gpio uses devm_* managed functions in mmc_gpio_request_cd()
now, we can remove those mmc_gpio_free_cd() call from host drivers'
.probe() error path and .remove().
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Chris Ball <cjb@laptop.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
Cc: Jarkko Lavinen <jarkko.lavinen@nokia.com>
Cc: Venkatraman S <svenkatr@ti.com>
Cc: Ian Molton <ian@mnementh.co.uk>
Cc: Bruce Chang <brucechang@via.com.tw>
Cc: Harald Welte <HaraldWelte@viatech.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Acked-by: NLudovic Desroches <ludovic.desroches@atmel.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The tmio-mmc driver is already using the generic GPIO CD handler in IRQ
mode. This patch adds support for CD polling mode and also checks for
availability of a WP GPIO.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Allow tmio mmc glue drivers to pass mmc_host::caps2 flags down to
the mmc layer.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Currently the TMIO MMC driver derives the OCR mask from the platform data
and uses a platform callback to turn card power on and off. This patch adds
regulator support to the driver.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Liam Girdwood <lrg@ti.com>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Every time the clock is enabled after possibly being disabled, we have
to re-read its frequency and update our configuration.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

We don't have to force-enable MMC interrupts in our .probe() method,
mmc_add_host() will trigger card detection, that will enable all the
necessary interrupts.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The tmio_mmc_set_ios() function configures the MMC power, clock and bus
width. When the mmc core requests the driver to power off the card, we
inform runtime PM, that the controller can be suspended. This can lead
to the MSTP clock being turned off.

Writing to any 16-bit hardware registers with the MSTP clock off leads
to timeouts and errors being printed to the kernel log. This can occur
both when stopping the MMC clock and when configuring the bus width.

To fix this, stop the MMC clock before calling put_runtime_pm(), and
skip bus width configuration when power is off.
Signed-off-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: NSimon Horman <horms@verge.net.au>
Acked-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

GPIOs can be used in MMC/SD-card slots not only for hotplug detection, but
also to implement the write-protection pin. Rename cd-gpio helpers to
slot-gpio to make addition of further slot GPIO functions possible.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

mmc.h defines macros for most frequently used MMC opcodes. Use them instead
of hard-coded numbers.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>