Semicolons are not necessary after switch/while/for/if braces
so remove them.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Even for keys that shouldn't be stored some use cases require the
knowledge of a new key having been created so that the conclusion of a
successful pairing can be made. Therefore, always send the mgmt_new_key
event but add a store_hint parameter to it to indicate to user space
whether the key should be stored or not.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

User space shouldn't have any need for the old key type so remove it
from the corresponding Management interface event.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

If a controller generates a changed combination key as its first key the
connection key type will not be correctly set. In these situations make
sure the update the connection key type when such a buggy controller is
detected.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Even if there's no previous key stored the connection might still be
secured with a non-persistent key and in that case the key type in the
hci_conn struct should be checked.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Link keys should only be stored if very specific criteria of the
authentication process are fulfilled. This patch essentially copies the
criteria that user space has so far been using to the kernel side so
that the management interface works properly.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Introduce the link key types defs and use them instead of magic numbers.
Signed-off-by: NWaldemar Rymarkiewicz <waldemar.rymarkiewicz@tieto.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

In the teardown path the reset command is sent to the controller,
this event causes the command timer to be reactivated.

So the timer is removed in two situations, when the adapter isn't
marked as UP and when we know that some command has been sent.
Reported-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

It is unnecessary, once we are always in interrupt context.
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

After we made debugobjects working again, we got the following:

WARNING: at lib/debugobjects.c:262 debug_print_object+0x8e/0xb0()
Hardware name: System Product Name
ODEBUG: free active (active state 0) object type: timer_list hint: hci_cmd_timer+0x0/0x60
Pid: 2125, comm: dmsetup Tainted: G        W   2.6.38-06707-gc62b3898 #110375
Call Trace:
 [<ffffffff8104700a>] warn_slowpath_common+0x7a/0xb0
 [<ffffffff810470b6>] warn_slowpath_fmt+0x46/0x50
 [<ffffffff812d3a5e>] debug_print_object+0x8e/0xb0
 [<ffffffff81bd8810>] ? hci_cmd_timer+0x0/0x60
 [<ffffffff812d4685>] debug_check_no_obj_freed+0x125/0x230
 [<ffffffff810f1063>] ? check_object+0xb3/0x2b0
 [<ffffffff810f3630>] kfree+0x150/0x190
 [<ffffffff81be4d06>] ? bt_host_release+0x16/0x20
 [<ffffffff81be4d06>] bt_host_release+0x16/0x20
 [<ffffffff813a1907>] device_release+0x27/0xa0
 [<ffffffff812c519c>] kobject_release+0x4c/0xa0
 [<ffffffff812c5150>] ? kobject_release+0x0/0xa0
 [<ffffffff812c61f6>] kref_put+0x36/0x70
 [<ffffffff812c4d37>] kobject_put+0x27/0x60
 [<ffffffff813a21f7>] put_device+0x17/0x20
 [<ffffffff81bda4f9>] hci_free_dev+0x29/0x30
 [<ffffffff81928be6>] vhci_release+0x36/0x70
 [<ffffffff810fb366>] fput+0xd6/0x1f0
 [<ffffffff810f8fe6>] filp_close+0x66/0x90
 [<ffffffff810f90a9>] sys_close+0x99/0xf0
 [<ffffffff81d4c96b>] system_call_fastpath+0x16/0x1b

That timer was introduced with commit 6bd32326(Bluetooth: Use
proper timer for hci command timout)

Timer seems to be running when the thing is closed. Removing the timer
unconditionally fixes the problem. And yes, it needs to be fixed
before the HCI_UP check.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

We can't send new commands before a cmd_complete for the HCI_RESET command
shows up.
Reported-by: NMikko Vinni <mmvinni@yahoo.com>
Reported-by: NJustin P. Mattock <justinmattock@gmail.com>
Reported-by: NEd Tomlinson <edt@aei.ca>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Tested-by: NJustin P. Mattock <justinmattock@gmail.com>
Tested-by: NMikko Vinni <mmvinni@yahoo.com>
Tested-by: NEd Tomlinson <edt@aei.ca>

This patch adds commands to add and remove remote OOB data to the managment
interface. Remote data is stored in kernel and can be used by corresponding
HCI commands and events when needed.
Signed-off-by: NSzymon Janc <szymon.janc@tieto.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

hci_notify() doesn't need declaration first.
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

After we made debugobjects working again, we got the following:

WARNING: at lib/debugobjects.c:262 debug_print_object+0x8e/0xb0()
Hardware name: System Product Name
ODEBUG: free active (active state 0) object type: timer_list hint: hci_cmd_timer+0x0/0x60
Pid: 2125, comm: dmsetup Tainted: G        W   2.6.38-06707-gc62b3898 #110375
Call Trace:
 [<ffffffff8104700a>] warn_slowpath_common+0x7a/0xb0
 [<ffffffff810470b6>] warn_slowpath_fmt+0x46/0x50
 [<ffffffff812d3a5e>] debug_print_object+0x8e/0xb0
 [<ffffffff81bd8810>] ? hci_cmd_timer+0x0/0x60
 [<ffffffff812d4685>] debug_check_no_obj_freed+0x125/0x230
 [<ffffffff810f1063>] ? check_object+0xb3/0x2b0
 [<ffffffff810f3630>] kfree+0x150/0x190
 [<ffffffff81be4d06>] ? bt_host_release+0x16/0x20
 [<ffffffff81be4d06>] bt_host_release+0x16/0x20
 [<ffffffff813a1907>] device_release+0x27/0xa0
 [<ffffffff812c519c>] kobject_release+0x4c/0xa0
 [<ffffffff812c5150>] ? kobject_release+0x0/0xa0
 [<ffffffff812c61f6>] kref_put+0x36/0x70
 [<ffffffff812c4d37>] kobject_put+0x27/0x60
 [<ffffffff813a21f7>] put_device+0x17/0x20
 [<ffffffff81bda4f9>] hci_free_dev+0x29/0x30
 [<ffffffff81928be6>] vhci_release+0x36/0x70
 [<ffffffff810fb366>] fput+0xd6/0x1f0
 [<ffffffff810f8fe6>] filp_close+0x66/0x90
 [<ffffffff810f90a9>] sys_close+0x99/0xf0
 [<ffffffff81d4c96b>] system_call_fastpath+0x16/0x1b

That timer was introduced with commit 6bd32326(Bluetooth: Use
proper timer for hci command timout)

Timer seems to be running when the thing is closed. Removing the timer
unconditionally fixes the problem. And yes, it needs to be fixed
before the HCI_UP check.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NIngo Molnar <mingo@elte.hu>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

We can't send new commands before a cmd_complete for the HCI_RESET command
shows up.
Reported-by: NMikko Vinni <mmvinni@yahoo.com>
Reported-by: NJustin P. Mattock <justinmattock@gmail.com>
Reported-by: NEd Tomlinson <edt@aei.ca>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Tested-by: NJustin P. Mattock <justinmattock@gmail.com>
Tested-by: NMikko Vinni <mmvinni@yahoo.com>
Tested-by: NEd Tomlinson <edt@aei.ca>

Signed-off-by: NSzymon Janc <szymon.janc@tieto.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Use proper timer instead of hci command flow control to timeout
failed hci commands. Otherwise stack ends up sending commands
when flow control is used to block new commands.

2010-09-01 18:29:41.592132 < HCI Command: Remote Name Request (0x01|0x0019) plen 10
    bdaddr 00:16:CF:E1:C7:D7 mode 2 clkoffset 0x0000
2010-09-01 18:29:41.592681 > HCI Event: Command Status (0x0f) plen 4
    Remote Name Request (0x01|0x0019) status 0x00 ncmd 0
2010-09-01 18:29:51.022033 < HCI Command: Remote Name Request Cancel (0x01|0x001a) plen 6
    bdaddr 00:16:CF:E1:C7:D7
Signed-off-by: NVille Tervo <ville.tervo@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

If the fail happens the HCI del_timer may timeout after the the hci dev
unregister. This lead to a kernel crash.
Reported-by: NVinicius Costa Gomes <vinicius.gomes@openbossa.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Separate LE and ACL timeouts. Othervise ACL connections
on non LE hw will time out after 45 secs.
Signed-off-by: NVille Tervo <ville.tervo@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Bluetooth chips may have separate buffers for LE traffic.
This patch add support to use LE buffers provided by the chip.
Signed-off-by: NVille Tervo <ville.tervo@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Fix checkpatch warnings concerning assignments in if conditions.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds a new set_io_capability management command which is used
to set the IO capability for Secure Simple Pairing (SSP) as well as the
Security Manager Protocol (SMP). The value is per hci_dev and each
hci_conn object inherits it upon creation.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds a management commands to feed the kernel with all stored
link keys as well as remove specific ones or all of them. Once the
load_keys command has been called the kernel takes over link key
replies. A new_key event is also added to inform userspace of newly
created link keys that should be stored permanently.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

User space should set the page timeout so there's no need to explicitly
set it in the HCI init sequence. Even if user space fails to set it the
controller default value will be used.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The controller may have link keys in its own memory and these keys could
be used for secure connections. However, since the interface to access
these keys doesn't provide information about the key types (which would
be needed to infer the level of security each key provides) using these
keys is rather useless. Therefore, simply clear the controller side list
in the initialization procedure.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

To support a more dynamic HCI initialization sequence the __hci_request
behavior requires some more changes. Particularly, the init sequence
should be able to have conditionals in it (sending some HCI commands
depending on the outcome of a previous command) instead of being a fixed
list as it is right now.

The reasons for these additional requirements are the moving all
previously user space driven initialization commands to the kernel side
as well as the support the Low Energy controllers.

To fulfull these requirements the init sequence is made the only special
case for multi-command requests and req_last_cmd is renamed to
init_last_cmd. The hci_send_cmd function is changed to update
init_last_cmd as long as the HCI_INIT flag is set.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds methods to the management interface for userspace to
notify the kernel of which services have been registered for specific
adapters. This information is needed for setting the appropriate Class
of Device value as well as the Extended Inquiry Response value. This
patch doesn't actually implement setting of these values but just
provides the storage of the UUIDs so the needed functionality can be
built on top of it.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch implements a new set_pairable management command to control
the pairable state of local adapters. The state is represented using a
new HCI_PAIRABLE flag in the hci_dev struct.

For backwards compatibility with older user space versions the
HCI_PAIRABLE flag gets automatically set when the existence of an
adapter is reported to user space through legacy methods and the
HCI_MGMT flag is not set.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds a set_powered command to the management interface
through which the powered state of local adapters can be controlled.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds support for the powered event that's used to indicate to
userspace when the powered state of a local adapter changes.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch implements automatic initialization of basic information
about newly registered Bluetooth adapters. E.g. the address and features
are always needed so it makes sense for the kernel to automatically
power on adapters and read this information. A new HCI_SETUP flag is
added to track this state.

In order to not consume unnecessary amounts of power if there isn't a
user space available that could switch the adapter back off, a timer is
added to do this automatically as long as no Bluetooth user space seems
to be present. A new HCI_AUTO_OFF flag is added that user space needs to
clear to avoid the automatic power off.

Additionally, the management interface index_added event is moved to the
end of the HCI_SETUP stage so a user space supporting the managment
inteface has all the necessary information available for fetching when
it gets notified of a new adapter. The HCI_DEV_REG event is kept in the
same place as before since existing HCI raw socket based user space
versions depend on seeing the kernels initialization sequence
(hci_init_req) to determine when the adapter is ready for use.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Modification of Nick Pelly <npelly@google.com> patch.

With Bluetooth 2.1 ACL packets can be flushable or non-flushable. This commit
makes ACL data packets non-flushable by default on compatible chipsets, and
adds the BT_FLUSHABLE socket option to explicitly request flushable ACL
data packets for a given L2CAP socket. This is useful for A2DP data which can
be safely discarded if it can not be delivered within a short time (while
other ACL data should not be discarded).

Note that making ACL data flushable has no effect unless the automatic flush
timeout for that ACL link is changed from its default of 0 (infinite).

Default packet types (for compatible chipsets):
Frame 34: 13 bytes on wire (104 bits), 13 bytes captured (104 bits)
Bluetooth HCI H4
Bluetooth HCI ACL Packet
    .... 0000 0000 0010 = Connection Handle: 0x0002
    ..00 .... .... .... = PB Flag: First Non-automatically Flushable Packet (0)
    00.. .... .... .... = BC Flag: Point-To-Point (0)
    Data Total Length: 8
Bluetooth L2CAP Packet

After setting BT_FLUSHABLE
(sock.setsockopt(274 /*SOL_BLUETOOTH*/, 8 /* BT_FLUSHABLE */, 1 /* flush */))
Frame 34: 13 bytes on wire (104 bits), 13 bytes captured (104 bits)
Bluetooth HCI H4
Bluetooth HCI ACL Packet
    .... 0000 0000 0010 = Connection Handle: 0x0002
    ..10 .... .... .... = PB Flag: First Automatically Flushable Packet (2)
    00.. .... .... .... = BC Flag: Point-To-Point (0)
    Data Total Length: 8
Bluetooth L2CAP Packet
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The blacklist should be freed before the hci device gets unregistered.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The initialization function used by hci_open_dev (hci_init_req) sends
many different HCI commands. The __hci_request function should only
return when all of these commands have completed (or a timeout occurs).
Several of these commands cause hci_req_complete to be called which
causes __hci_request to return prematurely.

This patch fixes the issue by adding a new hdev->req_last_cmd variable
which is set during the initialization procedure. The hci_req_complete
function will no longer mark the request as complete until the command
matching hdev->req_last_cmd completes.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

This patch adds Bluetooth Management interface events for controller
addition and removal. The events correspond to the existing HCI_DEV_REG
and HCI_DEV_UNREG stack internal events.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Do not use assignment in IF condition, remove extra spaces,
fixing typos, simplify code.
Signed-off-by: NAndrei Emeltchenko <andrei.emeltchenko@nokia.com>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

Clearing the blacklist in hci_dev_do_close() would mean that user space
needs to do extra work to re-block devices after a DEVDOWN-DEVUP cycle.
This patch removes the clearing of the blacklist in this case and
thereby saves user space from the extra work.
Signed-off-by: NJohan Hedberg <johan.hedberg@nokia.com>
Acked-by: NVille Tervo <ville.tervo@nokia.com>
Acked-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>

The bdaddr in the list root is completely unused and just
taking up space.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Tested-by: NJohan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Testing first we avoid enter the loop when count = 0.
Signed-off-by: NGustavo F. Padovan <padovan@profusion.mobi>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>