USB 3.0 devices may optionally support a new feature called Latency
Tolerance Messaging.  If both the xHCI host controller and the device
support LTM, it should be turned on in order to give the system hardware
a better clue about the latency tolerance values of its PCI devices.

Once a Set Feature request to enable LTM is received, the USB 3.0 device
will begin to send LTM updates as its buffers fill or empty, and it can
tolerate more or less latency.

The USB 3.0 spec, section C.4.2 says that LTM should be disabled just
before the device is placed into suspend.  Then the device will send an
updated LTM notification, so that the system doesn't think it should
remain in an active state in order to satisfy the latency requirements
of the suspended device.

The Set and Clear Feature LTM enable command can only be sent to a
configured device.  The device will respond with an error if that
command is sent while it is in the Default or Addressed state.  Make
sure to check udev->actconfig in usb_enable_ltm() and usb_disable_ltm(),
and don't send those commands when the device is unconfigured.

LTM should be enabled once a new configuration is installed in
usb_set_configuration().  If we end up sending duplicate Set Feature LTM
Enable commands on a switch from one installed configuration to another
configuration, that should be harmless.

Make sure that LTM is disabled before the device is unconfigured in
usb_disable_device().  If no drivers are bound to the device, it doesn't
make sense to allow the device to control the latency tolerance of the
xHCI host controller.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

hub_initiated_lpm_disable_count is not used by any code, so remove it.

This commit should be backported to kernels as old as 3.5, that contain
the commit 8306095f "USB: Disable USB
3.0 LPM in critical sections."
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable@vger.kernel.org

Sometimes, the driver bindings may know what phy they use.
For example, when using device tree, the usb controller may have a
phandler pointing to usb phy.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Acked-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NSubodh Nijsure <snijsure@grid-net.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This let usb phy driver has a chance to change hw settings when connect
status change.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Tested-by: NSubodh Nijsure <snijsure@grid-net.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Platform drivers do the similar things to add/remove ci13xxx device, so
create a unified one.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

struct ci13xxx represent the controller, which may be device or host,
so name its variables as ci.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Reviewed-by: NMarek Vasut <marex@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch rename struct ci13xxx_udc_driver and var with the type.

ci13xxx_platform_data reflect it's passed from platfrom driver.
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NAlexander Shishkin <alexander.shishkin@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When using urb->transfer_buffer we need to allocate physical contiguous buffers
for the entire transfer, which is pretty much guaranteed to fail with large
transfers.

Currently userspace works around this by breaking large transfers into multiple
urbs. For large bulk transfers this leads to all kind of complications.

This patch makes it possible for userspace to reliable submit large bulk
transfers to scatter-gather capable host controllers in one go, by using a
scatterlist to break the transfer up in managable chunks.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There are a few (new) usbdevfs capabilities which an application cannot
discover in any other way then checking the kernel version. There are 3
problems with this:
1) It is just not very pretty.
2) Given the tendency of enterprise distros to backport stuff it is not
reliable.
3) As discussed in length on the mailinglist, USBDEVFS_URB_BULK_CONTINUATION
does not work as it should when combined with USBDEVFS_URB_SHORT_NOT_OK
(which is its intended use) on devices attached to an XHCI controller.
So the availability of these features can be host controller dependent,
making depending on them based on the kernel version not a good idea.

This patch besides adding the new ioctl also adds flags for the following
existing capabilities:

USBDEVFS_CAP_ZERO_PACKET,        available since 2.6.31
USBDEVFS_CAP_BULK_CONTINUATION,  available since 2.6.32, except for XHCI
USBDEVFS_CAP_NO_PACKET_SIZE_LIM, available since 3.3

Note that this patch only does not advertise the USBDEVFS_URB_BULK_CONTINUATION
cap for XHCI controllers, bulk transfers with this flag set will still be
accepted when submitted to XHCI controllers.

Returning -EINVAL for them would break existing apps, and in most cases the
troublesome scenario wrt USBDEVFS_URB_SHORT_NOT_OK urbs on XHCI controllers
will never get hit, so this would break working use cases.

The disadvantage of not returning -EINVAL is that cases were it is causing
real trouble may go undetected / the cause of the trouble may be unclear,
but this is the best we can do.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix kernel-doc warning.  This struct member was removed in commit
87568264 ("irq: Remove irq_chip->release()") so remove its
associated kernel-doc entry also.

  Warning(include/linux/irq.h:338): Excess struct/union/enum/typedef member 'release' description in 'irq_chip'
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: Richard Weinberger <richard@nod.at>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch (as1562) cleans up the definitions of the EHCI extended
registers to be consistent with the definitions of the standard
registers.  This makes the code look a lot nicer, with no functional
change.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add task management support, wind up in abort and device reset error
handlers.  Cancel all in-flight urbs in bus reset handler.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 2603efa3 ("bug.h: Fix up powerpc build regression") corrected
the powerpc build case and extended the __ASSEMBLY__ guards, but it also
got caught in pre-processor hell accidentally matching the else case of
CONFIG_BUG resulting in the BUG disabled case tripping up on
-Werror=implicit-function-declaration.

It's not possible to __ASSEMBLY__ guard the entire file as architecture
code needs to get at the BUGFLAG_WARNING definition in the GENERIC_BUG
case, but the rest of the CONFIG_BUG=y/n case needs to be guarded.

Rather than littering endless __ASSEMBLY__ checks in each of the if/else
cases we just move the BUGFLAG definitions up under their own
GENERIC_BUG test and then shove everything else under one big
__ASSEMBLY__ guard.

Build tested on all of x86 CONFIG_BUG=y, CONFIG_BUG=n, powerpc (due to
it's dependence on BUGFLAG definitions in assembly code), and sh (due to
not bringing in linux/kernel.h to satisfy the taint flag definitions used
by the generic bug code).

Hopefully that's the end of the corner cases and I can abstain from ever
having to touch this infernal header ever again.
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Tested-by: NFengguang Wu <wfg@linux.intel.com>
Acked-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The atomic notifier from twl4030/twl6030 to notifiy VBUS and ID events,
is replaced by a direct call to omap musb blue.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Used devres API's to associate the phy with a device so that on
driver detach, release function is invoked on the devres data(usb_phy)
and devres data(usb_phy) is released.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add a linked list for keeping multiple PHY instances with different
types so that we can have separate USB2 and USB3 PHYs on one single
board. _get_phy_ has been changed so that the controller gets
the transceiver by type. _remove_phy_ has been added to let the phy
be removed from the phy list.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

_transceiver() in otg.c is replaced with _phy. usb_set_transceiver is
replaced with usb_add_phy to make it similar to other usb standard
function names like usb_add_hcd.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Several bug reports have been received recently for USB mass-storage
devices that don't handle READ CAPACITY(16) commands properly.  They
report bogus sizes, in some cases becoming unusable as a result.

The bugs were triggered by commit
09b6b51b (SCSI & usb-storage: add
flags for VPD pages and REPORT LUNS), which caused usb-storage to stop
overriding the SCSI level reported by devices.  By default, the sd
driver will try READ CAPACITY(16) first for any device whose level is
above SCSI_SPC_2.

It seems likely that any device large enough to require the use of
READ CAPACITY(16) (i.e., 2 TB or more) would be able to handle READ
CAPACITY(10) commands properly.  Indeed, I don't know of any devices
that don't handle READ CAPACITY(10) properly.

Therefore this patch (as1559) adds a new flag telling the sd driver
to try READ CAPACITY(10) before READ CAPACITY(16), and sets this flag
for every USB mass-storage device.  If a device really is larger than
2 TB, sd will fall back to READ CAPACITY(16) just as it used to.

This fixes Bugzilla #43391.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: NHans de Goede <hdegoede@redhat.com>
CC: "James E.J. Bottomley" <JBottomley@parallels.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This comment is well out of date.
Signed-off-by: NDave Airlie <airlied@redhat.com>

Guard vga_switcheroo.h against multiple inclusion.
Signed-off-by: NOzan Çağlayan <ozancag@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

viresh.kumar@st.com email-id doesn't exist anymore as I have left the
company.  Replace ST's id with viresh.linux@gmail.com.

It also updates .mailmap file to fix address for 'git shortlog'
Signed-off-by: NViresh Kumar <viresh.linux@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

In the x86 32bit PAE CONFIG_TRANSPARENT_HUGEPAGE=y case while holding the
mmap_sem for reading, cmpxchg8b cannot be used to read pmd contents under
Xen.

So instead of dealing only with "consistent" pmdvals in
pmd_none_or_trans_huge_or_clear_bad() (which would be conceptually
simpler) we let pmd_none_or_trans_huge_or_clear_bad() deal with pmdvals
where the low 32bit and high 32bit could be inconsistent (to avoid having
to use cmpxchg8b).

The only guarantee we get from pmd_read_atomic is that if the low part of
the pmd was found null, the high part will be null too (so the pmd will be
considered unstable).  And if the low part of the pmd is found "stable"
later, then it means the whole pmd was read atomically (because after a
pmd is stable, neither MADV_DONTNEED nor page faults can alter it anymore,
and we read the high part after the low part).

In the 32bit PAE x86 case, it is enough to read the low part of the pmdval
atomically to declare the pmd as "stable" and that's true for THP and no
THP, furthermore in the THP case we also have a barrier() that will
prevent any inconsistent pmdvals to be cached by a later re-read of the
*pmd.
Signed-off-by: NAndrea Arcangeli <aarcange@redhat.com>
Cc: Jonathan Nieder <jrnieder@gmail.com>
Cc: Ulrich Obergfell <uobergfe@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: Larry Woodman <lwoodman@redhat.com>
Cc: Petr Matousek <pmatouse@redhat.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Tested-by: NAndrew Jones <drjones@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

On arches that do not support this_cpu_cmpxchg_double() slab_lock is used
to do atomic cmpxchg() on double word which contains page->_count.  The
page count can be changed from get_page() or put_page() without taking
slab_lock.  That corrupts page counter.

Fix it by moving page->_count out of cmpxchg_double data.  So that slub
does no change it while updating slub meta-data in struct page.

[akpm@linux-foundation.org: use standard comment layout, tweak comment text]
Reported-by: NAmey Bhide <abhide@nicira.com>
Signed-off-by: NPravin B Shelar <pshelar@nicira.com>
Acked-by: NChristoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NKay Sievers <kay@vrfy.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: NRandy Dunlap <rdunlap@xenotime.net>
Reported-by: NFengguang Wu <wfg@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On some systems, struct usb_device_id doesn't align properly due to the
recent changes in it.  So pad out the driver_info field to align on a
boundry that systems can handle it.
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Cc: Bjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The asm-generic/bug.h __ASSEMBLY__ guarding is completely bogus, which
tripped up the powerpc build when the kernel.h include was added:

	In file included from include/asm-generic/bug.h:5:0,
			 from arch/powerpc/include/asm/bug.h:127,
			 from arch/powerpc/kernel/head_64.S:31:
	include/linux/kernel.h:44:0: warning: "ALIGN" redefined [enabled by default]
	include/linux/linkage.h:57:0: note: this is the location of the previous definition
	include/linux/sysinfo.h: Assembler messages:
	include/linux/sysinfo.h:7: Error: Unrecognized opcode: `struct'
	include/linux/sysinfo.h:8: Error: Unrecognized opcode: `__kernel_long_t'

Moving the __ASSEMBLY__ guard up and stashing the kernel.h include under
it fixes this up, as well as covering the case the original fix was
attempting to handle.
Tested-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 5963e317 ("ftrace/x86: Do not change stacks in DEBUG when
calling lockdep") prevented lockdep calls from the int3 breakpoint handler
from reseting the stack if a function that was called was in the process
of being converted for tracing and had a breakpoint on it. The idea is,
before calling the lockdep code, do a load_idt() to the special IDT that
kept the breakpoint stack from reseting. This worked well as a quick fix
for this kernel release, until a certain config caused a lockup in the
function tracer start up tests.

Investigating it, I found that the load_idt that was used to prevent
the int3 from changing stacks was itself being traced!

Even though the config had CONFIG_OPTIMIZE_INLINING disabled, and
all 'inline' tags were set to always inline, there were still cases that
it did not inline! This was caused by CONFIG_PARAVIRT_GUEST, where it
would add a pointer to the native_load_idt() which made that function
to be traced.

Commit 45959ee7 ("ftrace: Do not function trace inlined functions")
only touched the 'inline' tags when CONFIG_OPMITIZE_INLINING was enabled.
PARAVIRT_GUEST shows that this was not enough and we need to also
mark always_inline with notrace as well.
Reported-by: NFengguang Wu <wfg@linux.intel.com>
Tested-by: NFengguang Wu <wfg@linux.intel.com>
Signed-off-by: NSteven Rostedt <rostedt@goodmis.org>

Currently there is a 'chicken and egg' issue when the DS is also the mounted
MDS. The nfs_match_client() reference from nfs4_set_ds_client bumps the
cl_count, the nfs_client is not freed at umount, and nfs4_deviceid_purge_client
is not called to dereference the MDS usage of a deviceid which holds a
reference to the DS nfs_client.  The result is the umount program returns,
but the nfs_client is not freed, and the cl_session hearbeat continues.

The MDS (and all other nfs mounts) lose their last nfs_client reference in
nfs_free_server when the last nfs_server (fsid) is umounted.
The file layout DS lose their last nfs_client reference in destroy_ds
when the last deviceid referencing the data server is put and destroy_ds is
called. This is triggered by a call to nfs4_deviceid_purge_client which
removes references to a pNFS deviceid used by an MDS mount.

The fix is to track how many pnfs enabled filesystems are mounted from
this server, and then to purge the device id cache once that count reaches
zero.
Reported-by: NJorge Mora <Jorge.Mora@netapp.com>
Reported-by: NAndy Adamson <andros@netapp.com>
Signed-off-by: NTrond Myklebust <Trond.Myklebust@netapp.com>

Signed-off-by: NRémi Denis-Courmont <remi@remlab.net>
Cc: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix warnings on some architectures/configs (not on x86):

include/linux/vga_switcheroo.h:28:30: warning: 'struct pci_dev' declared inside parameter list [enabled by default]
include/linux/vga_switcheroo.h:28:30: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
Signed-off-by: NRandy Dunlap <rdunlap@xenotime.net>
Cc:	Takashi Iwai <tiwai@suse.de>
Reported-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This reverts commit 2a0c451a.

It causes crashes, because now ip6_null_entry is used before
it is initialized.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Minchan Kim reports that when a system has many swap areas, and tmpfs
swaps out to the ninth or more, shmem_getpage_gfp()'s attempts to read
back the page cannot locate it, and the read fails with -ENOMEM.

Whoops.  Yes, I blindly followed read_swap_header()'s pte_to_swp_entry(
swp_entry_to_pte()) technique for determining maximum usable swap
offset, without stopping to realize that that actually depends upon the
pte swap encoding shifting swap offset to the higher bits and truncating
it there.  Whereas our radix_tree swap encoding leaves offset in the
lower bits: it's swap "type" (that is, index of swap area) that was
truncated.

Fix it by reducing the SWP_TYPE_SHIFT() in swapops.h, and removing the
broken radix_to_swp_entry(swp_to_radix_entry()) from read_swap_header().

This does not reduce the usable size of a swap area any further, it
leaves it as claimed when making the original commit: no change from 3.0
on x86_64, nor on i386 without PAE; but 3.0's 512GB is reduced to 128GB
per swapfile on i386 with PAE.  It's not a change I would have risked
five years ago, but with x86_64 supported for ten years, I believe it's
appropriate now.

Hmm, and what if some architecture implements its swap pte with offset
encoded below type? That would equally break the maximum usable swap
offset check.  Happily, they all follow the same tradition of encoding
offset above type, but I'll prepare a check on that for next.
Reported-and-Reviewed-and-Tested-by: NMinchan Kim <minchan@kernel.org>
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org [3.1, 3.2, 3.3, 3.4]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

/proc/net/ipv6_route reflects the contents of fib_table_hash. The proc
handler is installed in ip6_route_net_init() whereas fib_table_hash is
allocated in fib6_net_init() _after_ the proc handler has been installed.

This opens up a short time frame to access fib_table_hash with its pants
down.

fib6_init() as a whole can't be moved to an earlier position as it also
registers the rtnetlink message handlers which should be registered at
the end. Therefore split it into fib6_init() which is run early and
fib6_init_late() to register the rtnetlink message handlers.
Signed-off-by: NThomas Graf <tgraf@suug.ch>
Reviewed-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Orphaning skb in dev_hard_start_xmit() makes bonding behavior
unfriendly for applications sending big UDP bursts : Once packets
pass the bonding device and come to real device, they might hit a full
qdisc and be dropped. Without orphaning, the sender is automatically
throttled because sk->sk_wmemalloc reaches sk->sk_sndbuf (assuming
sk_sndbuf is not too big)

We could try to defer the orphaning adding another test in
dev_hard_start_xmit(), but all this seems of little gain,
now that BQL tends to make packets more likely to be parked
in Qdisc queues instead of NIC TX ring, in cases where performance
matters.

Reverts commits :
fc6055a5 net: Introduce skb_orphan_try()
87fd308c net: skb_tx_hash() fix relative to skb_orphan_try()
and removes SKBTX_DRV_NEEDS_SK_REF flag
Reported-and-bisected-by: NJean-Michel Hautbois <jhautbois@gmail.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Tested-by: NOliver Hartkopp <socketcan@hartkopp.net>
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Provide an iterator to receive the log buffer content, and convert all
kmsg_dump() users to it.

The structured data in the kmsg buffer now contains binary data, which
should no longer be copied verbatim to the kmsg_dump() users.

The iterator should provide reliable access to the buffer data, and also
supports proper log line-aware chunking of data while iterating.
Signed-off-by: NKay Sievers <kay@vrfy.org>
Tested-by: NTony Luck <tony.luck@intel.com>
Reported-by: NAnton Vorontsov <anton.vorontsov@linaro.org>
Tested-by: NAnton Vorontsov <anton.vorontsov@linaro.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A handy function that we will use outside of ram_core soon. But
so far just factor it out and start using it in post_init().
Signed-off-by: NAnton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Without the update, we'll only see the new dmesg buffer after the
reboot, but previously we could see it right away. Making an oops
visible in pstore filesystem before reboot is a somewhat dubious
feature, but removing it wasn't an intentional change, so let's
restore it.

For this we have to make persistent_ram_save_old() safe for calling
multiple times, and also extern it.
Signed-off-by: NAnton Vorontsov <anton.vorontsov@linaro.org>
Acked-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some composite USB devices provide multiple interfaces
with different functions, all using "vendor-specific"
for class/subclass/protocol.  Another OS use interface
numbers to match the driver and interface. It seems
these devices are designed with that in mind - using
static interface numbers for the different functions.

This adds support for matching against the
bInterfaceNumber, allowing such devices to be supported
without having to resort to testing against interface
number whitelists and/or blacklists in the probe.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch (as1558) fixes a problem affecting several ASUS computers:
The machine crashes or corrupts memory when going into suspend if the
ehci-hcd driver is bound to any controllers.  Users have been forced
to unbind or unload ehci-hcd before putting their systems to sleep.

After extensive testing, it was determined that the machines don't
like going into suspend when any EHCI controllers are in the PCI D3
power state.  Presumably this is a firmware bug, but there's nothing
we can do about it except to avoid putting the controllers in D3
during system sleep.

The patch adds a new flag to indicate whether the problem is present,
and avoids changing the controller's power state if the flag is set.
Runtime suspend is unaffected; this matters only for system suspend.
However as a side effect, the controller will not respond to remote
wakeup requests while the system is asleep.  Hence USB wakeup is not
functional -- but of course, this is already true in the current state
of affairs.

A similar patch has already been applied as commit
151b6128 (USB: EHCI: fix crash during
suspend on ASUS computers).  The patch supersedes that one and reverts
it.  There are two differences:

	The old patch added the flag at the USB level; this patch
	adds it at the PCI level.

	The old patch applied to all chipsets with the same vendor,
	subsystem vendor, and product IDs; this patch makes an
	exception for a known-good system (based on DMI information).
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Tested-by: NDâniel Fraga <fragabr@gmail.com>
Tested-by: NAndrey Rahmatullin <wrar@wrar.name>
Tested-by: NSteven Rostedt <rostedt@goodmis.org>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: NRafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

 - to decrease redundant since both ehci_hcd and ohci_hcd have the same variable
 - it helps access phy in usb core code
 - phy is more meaningful than transceiver
Signed-off-by: NRichard Zhao <richard.zhao@freescale.com>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>