Power down the s5h1411 demodulator when not in use (on the Pinnacle 801e, this
brings idle power from 123ma down to 84ma).
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Acked-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If we are already at the desired modulation, there is no need to reconfigure
the demod (at a tuning time cost)

Note that this change revealed that although the datasheet says the demod
starts out in VSB-8 mode, the first tuning was failing consistently unless
we went through the work of setting the registers.  So add a field to denote
this case so we always do the enable_frontend call, even if the first tuning
request is for VSB-8.
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Acked-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

If you instruct the tuner to change frequencies, it can take up to 2500ms to
get a demod lock.  By performing a soft reset after the tuning call (which
is consistent with how the Pinnacle 801e Windows driver behaves), you get
a demod lock inside of 300ms
Signed-off-by: NDevin Heitmueller <devin.heitmueller@gmail.com>
Reviewed-by: NMichael Krufky <mkrufky@linuxtv.org>
Acked-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

s5h1411: Add the #define for an existing supporting I/F
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

s5h1411: Remove meaningless code
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Adding a serialmode function to read/and/or/write the register for safety.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This includes new bit definitions for previously unknown bits.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This should improve performance.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

s5h1411: Improvements to the default registers
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A consolidated implementation will provide this generically through
asm/byteorder, remove direct includes to avoid breakage when the
changeover to the new implementation occurs.
Signed-off-by: NHarvey Harrison <harvey.harrison@gmail.com>
Acked-by: NMauro Carvalho Chehab <mchehab@infradead.org>
Acked-by: N"Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Remove warning message during cx88-dvb compilation.
Also fixes double underline in function and struct names.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

| drivers/media/dvb/frontends/cx24116.c:573: warning: passing argument 3 of 'cx24116_writeregN' discards qualifiers from pointer target type

Make the `data' input pointer parameter of cx24116_writeregN() const to
kill the warning.
Signed-off-by: NGeert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove spurious messages and turn into debug.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Christophe divulged the following:
"Since 8PSK (and higher mod) signals are very likely to have pilot symbols,
pilot_auto should start with pilot_on for 8PSK.
And since QPSK signals are unlikely to have pilot, pilot_auto should start
with pilot_off for QPSK.

Without the patch:
QPSK tuning delay: ~100ms
8PSK tuning delay: ~900ms
with patch:
QPSK tuning delay: ~100ms
8PSK tuning delay: ~100ms
"

This patch does as Cristophe asks. In emulated auto-pilot we
choose pilot-on for tuning PSK_8 and pilot-off for
tuning QPSK.
Signed-off-by: NDarron Broad <darron@kewl.org>
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

When moving from one frontend to another
an application could spawn multiple threads opening
the same new frontend and in some circumstances all of
these could become delayed waiting for the previous
frontend readers or previous frontend writer thread to
complete.

In this scenario the first thread will succeed on open
to bring the new frontend online but any others will return
EBUSY. This is a fault.  If the first succeeds and all others
are on the same frontend then they should succeed also.
Signed-off-by: NDarron Broad <darron@kewl.org>
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cx24123: Checkpatch compliance
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

s5h1411: Checkpatch compliance
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

s5h1409: Checkpatch compliance
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cx24116: Checkpatch compliance #3
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cx22702: Checkpatch compliance
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

tda10048: Checkpatch compliance
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cx24116: Checkpatch compliance #2
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

cx24116: Checkpatch compliance
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Autodetect 2040:5520 and 2040:5530 as Hauppauge WinTV MiniStick
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This add frontend R/W mutual exclusion.
Prior to this point in time it was possible to open both
frontends simultaneously which an MFE card cannot support.

In order to stop this, a delayed open is performed which
has the following function:

-  Return EBUSY after a configurable amount of time
   if a frontend is unavailable due to the other being
   in use.

-  Only allow opening of a frontend if the kernel thread
   of the other has stopped.

This solution was chosen to allow switching between
frontends to work as seamlessly as possible. When both
frontends are actually opened simultaneously then one
will only open, but if quick switching is performed
between one of many then the new open will succeed in
a clean fashion rather than interrupting a kernel
thread.
Signed-off-by: NDarron Broad <darron@kewl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A detailed description from the original patches 2 years ago:

"The WinTV-HVR3000 has a single transport bus which is shared between
a DVB-T and DVB-S modulator. These patches build on the bus acquisition
cx88 work from a few weeks ago to add support for this.

So to applications the HVR3000 looks like this:
/dev/dvb/adapter0/fe0 (cx24123 DVB-S demod)
/dev/dvb/adapter0/fe1 (cx22702 DVB-T demod)

Additional boards continue as before, eg:
/dev/dvb/adapter1/fe0 (lgdt3302 ATSC demod)

The basic change is removing the single instance of the videobuf_dvb in
cx8802_dev and saa7134_dev(?) and replacing it with a list and some
supporting functions.

*NOTE* This branch was taken before v4l-dvb was closed for 2.6.19 so
two or three current cx88 patches appear to be reversed by this tree,
this will be cleaned up in the near future. The patches missing change
the mutex handing to core->lock, fix an enumeration problem."

It should be recognised that a number of people have been maintaining
this patchset. Significant levels of Kudos to everyone one involved,
including but not limited to:

Darron Broad
Fabio M. Di Nitto
Carlo Scarfoglio
Hans Werner

Without the work of these people, and countless others, my two year old
patches would of died on the Mercurial linuxtv.org vine a long time
ago.

TODO: Revise these patches a little further so that the need for
demux1 and dvr0 is optional, not mandatory on the HVR3000.

HISTORY (darron):
This is the last update to MFE prepared by Hans which is based
upon the `scratchpad' diff created by Carlo.
All MFE work prior to that point must be attributed to Fabio
who ported and maintained Steve's original patch up to that
time.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NDarron Broad <darron@kewl.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Signed-off-by: NManu Abraham <manu@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Now that device_create() has been audited, rename things back to the
original call to be sane.
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

cx24116: Change the default SNR units back to percentage by default.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

S2API: Return error of the caller provides 0 commands.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

A user tuning DVB-T via the S2API reports that this was not implemented,
and his tuning was failing.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Tuning DVB-T via the S2API was failing, missing some essential items.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Reports from users that using the new API for tuning DTV was failing,
and the cache was missing some essential items.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

I've retained the older percentage code after discussing this with
Darron Broad, but made the ESNO option default.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

... and cleanup any drivers using them.
I've also removed NBC_QPSK and modified the cx24116 driver to check
the delivery_type also, removing some excess namespace baggage.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Add support for DvbWorld USB cards with STV0288 demodulator.
Those cards use Earda EDS-1547 tuner.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Remove NULL pointer in stb6000 driver,
as it raises error for DvbWorld USB card.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Allow custom inittab for ST STV0288 demodulator,
as it is needed for DvbWorld USB card.
Signed-off-by: NIgor M. Liplianin <liplianin@me.by>
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

This means that when developers add new commands then they'll be see
the DTV_MAX_COMMAND define and will be more likely to modify it, without
having to modify the command validation code.
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>

Fixes switching from S2API to legacy where legacy params given to S2API
aware demods are cached ones and not those implied in the legacy API.

It was found (on an S2API aware demod at least) that after using
an S2API aware application and then switching to a legacy application
that prior S2API params were in effect were legacy has only
implied values. This fixes this.
Signed-off-by: NDarron Broad <darron@kewl.org>
Signed-off-by: NSteven Toth <stoth@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@redhat.com>