Add support for Satelco EasyWatch PCI DVB-S card (subsystem 0x1894:0x001b).
Signed-off-by: NOliver Endriss <o.endriss@gmx.de>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Now that dvb-pll is being used properly in all cx88-dvb instances,
the cx88 driver no longer needs to store pll_desc nor pll_addr.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Enhance the dvb-pll definition of the fmd1216 tuner by adding an init sequence
and a sleep sequence.

The init sequence sets the AGC control register to 0xa0, selecting the fast
time constant and 112 dBuV take-over point.  This the recommended value for
DVB-T operation.

The sleep sequence sets bit P4 (which is believed to turn the analog
demodulator on), turns off the tuning voltage, and sets the AGC control
register to 0x60 (external AGC voltage, the recommended value for analog
operation).

The existing dvb-pll users in the cx88 driver, listed below, will gain these
init and sleep sequences.

CX88_BOARD_HAUPPAUGE_HVR1100    Hauppauge WinTV-HVR1100 DVB-T/Hybrid
CX88_BOARD_HAUPPAUGE_HVR1100LP  Hauppauge WinTV-HVR1100 DVB-T/Hybrid (Low Profi
CX88_BOARD_WINFAST_DTV2000H     WinFast DTV2000 H
CX88_BOARD_HAUPPAUGE_HVR3000    Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DV
CX88_BOARD_HAUPPAUGE_HVR1300    Hauppauge WinTV-HVR1300 DVB-T/Hybrid MPEG Encod

This non-dvb-pll user in the cx88 driver should only gain the sleep sequence,
as it already had an equivalent init sequence.  The non-dvb-pll code for this
user is removed.

X88_BOARD_DNTV_LIVE_DVB_T_PRO   digitalnow DNTV Live! DVB-T Pro

In these saa7134 driver, these non-dvb-pll users are converted to use dvb-pll:

SAA7134_BOARD_MD7134                    Medion 7134
SAA7134_BOARD_ASUS_EUROPA2_HYBRID       Asus Europa2 OEM

The saa7134 functions philips_fmd1216_tuner_init(),
philips_fmd1216_tuner_sleep(), and philips_fmd1216_tuner_set_params() are
deleted and the dvb-pll versions are used.

This should result in equivalent sleep, init, and tuning sequences being sent
to the tuner.

For the cxusb driver, only one board is effected:

USB_PID_MEDION_MD95700          	Medion MD95700

This board used dvb_usb_tuner_init_i2c() and dvb_usb_tuner_set_params_i2c()
for init and tuning, respectively.  These functions are effectively the same
as the dvb-pll versions.  They call a tuner pass control function defined at
the dvb-usb level, but this does not matter, as this card does not have a
tuner pass control function (only the dib3000mb does).  This board will gain
the sleep sequence, while init and tuning should be unchanged.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Support for A-LINK DTU(m) is not included in this patch.
Signed-off-by: NAapo Tahkola <aet@rasterburn.org>
Acked-by: NAntti Palosaari <crope@iki.fi>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Marked af9005 driver as experimental and add dependency for qt1010;
Added a dependency on qt1010 in Kconfig;
Corrected the experimental gain  reduction of the mt2060 in case of
strong signal (though it is code included in #ifdef 0).
Signed-off-by: NLuca Olivetti <luca@ventoso.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NLuca Olivetti <luca@ventoso.org>
Signed-off-by: NManu Abraham <abraham.manu@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

convert calls to dib3000mb_attach to use dvb_attach
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

moved tda665x pll_init into dvb_pll_desc dvb_pll_tda665x.initdata
convert handling of tda665x and tua6010xs to properly use dvb-pll
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

These sources do not need to #include "dvb-pll.h"
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Using Encore's key codes, we needn't add any additional key table.
Signed-off-by: NTony Wan <wankai@sjtu.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Support the 10moons TM300 TV card (so called TV Master 3), which is a
10moons saa7130 based board.  Here not include features for the
IR-remote.
It has been tested using TVTIME.  The card was auto-detected and all the
input sources worked correct with sound.
Signed-off-by: NTony Wan <wankai@sjtu.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

The ioctl entry point, a big switch/case, is splitted in little 
functions. 

These functions are set as callbacks for the video_ioctl2 video4linux 
facility.

This improves the driver memory consumption and enables the v4l1 
compatibility as a side effect.
Signed-off-by: NThierry MERLE <thierry.merle@free.fr>
Acked-by: NDwaine P. Garden <dwainegarden@rogers.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Radio and video ioctls are the same,
delete the usbvision_do_radio_ioctl function
add the special cases for radio in usbvision_v4l2_do_ioctl
Signed-off-by: NThierry MERLE <thierry.merle@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

usbvision_set_video_format: add comment that VO_MODE is also being set.
Signed-off-by: NDavid Warman <dwarman@davidwarman.net>
Signed-off-by: NThierry MERLE <thierry.merle@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NDavid Warman <dwarman@davidwarman.net>
Signed-off-by: NThierry MERLE <thierry.merle@free.fr>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

removed philips_sd1878_tda8261_tuner_set_params, using dvb_pll_attach, instead.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

removed mt352_aver777_tuner_calc_regs, using dvb_pll_attach, instead.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This patch removes duplicate code from cx88-dvb and saa7134-dvb that handles
rf input switching for the TUV1236d tuner.

The functionality is added to dvb-pll, where all the other code that 
handles the TUV1236d is kept.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Rename dvb_pll_desc.setbw() to set(), and accept struct dvb_frontend_parameters
instead of passing both freq and bandwidth, so that this may be used as a
generic function.

In order to do this, dvb_pll_configure must also be altered in the same manner,
to take struct dvb_frontend_parameters instead of freq and bandwidth.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

All the printks had missing level prefixes so I've fixed these too.
Also fixed some grammer errors.
Signed-off-by: NSimon Arlott <simon@fire.lp0.eu>
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

If cx88 support is compiled into the kernel while vp3054 is left as a module,
the kernel will fail to link.  Adjust the existing "#if" code in cx88 so
that it won't consider vp3054 to be supported in this case.

It might make sense to move vp3054 selection into the "customisation" menu
instead of a cx88 sub-option (though this is a cx88 feature, there is no extra
chip involved).

It might also make sense to use dvb_attach() to load vp3054 support.
Signed-off-by: NTrent Piepho <xyzzy@speakeasy.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This driver were made based on tea5761 specs.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This is a reimplementation of the zs driver for the serial subsystem.  Any
resemblance to the old driver is purely coincidential.  ;-) I do hope I got
the handling of modem lines right -- better do not tackle me about the
issue unless you feel too good...

Any users of the old driver: please note the numbers of the serial lines
have now been swapped, i.e.  ttyS0 <-> ttyS1 and ttyS2 <-> ttyS3.  It has
to do with the modem lines mentioned above; basically the port A in a given
chip has to be initialised before the port B if you want to use the latter
as the serial console (which is usually the case), as operations on modem
lines of the serial line associated with the port B access both ports (see
the comment at the top of the driver for the details of wiring used).
Please update your scripts.

This is also the reason each SCC now requests an IRQ once only (as seen in
"/proc/interrupts") -- the handler takes care of both ports at once as the
line associated with the port B has to take status update interrupts from
both ports (and yet the line of the port A takes its own for itself too).
The old driver never got it right...
Signed-off-by: NMaciej W. Rozycki <macro@linux-mips.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

early_serial_setup was removed from serial.h, but forgot to put in
serial_8250.h
Signed-off-by: NYinghai Lu <yinghai.lu@sun.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

We can't show the extra logo from boot code if FB is built as a module.
Make the FB_LOGO_EXTRA depend on FB=y.
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Acked-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

If, in dm_create_persistent(), the call to create_singlethread_workqueue()
fails then we'll return without freeing the memory allocated to 'ps', thus
leaking sizeof(struct pstore) bytes.  This patch fixes the leak.

Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com
Acked-by: NAlasdair G Kergon <agk@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

With the slab zeroing allocations cleanups Christoph stubbed in a generic
kzalloc(), which was missed on SLOB. Follow the SLAB/SLUB changes and
kill off the __kzalloc() wrapper that SLOB was using.
Reported-by: NJan Engelhardt <jengelh@computergmbh.de>
Signed-off-by: NPaul Mundt <lethal@linux-sh.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The old IDE driver is not ready to take generic SCSI commands, even if
it uses them for some specific issues (ie the tray open/close ioctls for
IDE CD-ROM's). Pointed out by Bartlomiej.

I'm sure we'll have it fixed properly soon enough, but for now we should
not allow it to cause problems.

Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

I really don't see anybody else wanting to select it ;)
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
  [S390] Fix broken logic, SIGA flags must be bitwise ORed
  [S390] cio: Dont print trailing \0 in modalias_show().
  [S390] Simplify stack trace.
  [S390] z/VM unit record device driver
  [S390] vmcp cleanup
  [S390] qdio: output queue stall on FCP and network devices
  [S390] Fix disassembly of RX_URRD, SI_URD & PC-relative instructions.
  [S390] Update default configuration.

* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: (21 commits)
  [WATCHDOG] at32ap700x_wdt.c - Fix compilation warnings
  [WATCHDOG] at32ap700x_wdt.c - Add spinlock support
  [WATCHDOG] at32ap700x_wdt.c - Add nowayout + MAGICCLOSE features
  [WATCHDOG] at32ap700x_wdt.c - timeout module parameter patch
  [WATCHDOG] at32ap700x_wdt.c - checkpatch.pl-0.05 clean-up's
  [WATCHDOG] change s3c2410_wdt to using dev_() macros for output
  [WATCHDOG] s3c2410_wdt announce initialisation
  [WATCHDOG] at32ap700x-wdt: add iounmap if probe function fails
  [WATCHDOG] at32ap700x-wdt: add missing iounmap in _remove
  [WATCHDOG] watchdog-driver-for-at32ap700x-devices-fix-2
  [WATCHDOG] watchdog-driver-for-at32ap700x-devices-fix
  [WATCHDOG] Watchdog driver for AT32AP700X devices
  [WATCHDOG] Mixcom Watchdog - CodingStyle clean-up
  [WATCHDOG] Mixcom Watchdog - clean-up printk's
  [WATCHDOG] Mixcom Watchdog - clean-up printk's
  [WATCHDOG] Mixcom Watchdog - checkcard part 2
  [WATCHDOG] Mixcom Watchdog - checkcard
  [WATCHDOG] Mixcom Watchdog - get rid of port offset's
  [WATCHDOG] Mixcom Watchdog - update "Documentation"
  [WATCHDOG] Remove the redundant check for pwrite() in EP93XXX watchdog.
  ...

* 'bsg' of git://git.kernel.dk/data/git/linux-2.6-block:
  bsg: fix missing space in version print
  Don't define empty struct bsg_class_device if !CONFIG_BLK_DEV_BSG
  bsg: Kconfig updates
  bsg: minor cleanup
  bsg: device hash table cleanup
  bsg: fix initialization error handling bugs
  bsg: mark FUJITA Tomonori as bsg maintainer
  bsg: convert to dynamic major
  bsg: address various review comments

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: fix debug compilation error

* 'isdn-cleanup' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  [ISDN] HiSax hfc_pci: minor cleanups
  [ISDN] HiSax bkm_a4t: split setup into two smaller functions
  [ISDN] HiSax enternow: split setup into 3 smaller functions
  [ISDN] HiSax netjet_u: split setup into 3 smaller functions
  [ISDN] HiSax netjet_s: code movement, prep for hotplug
  [ISDN] HiSax: move card state alloc/setup code into separate functions
  [ISDN] HiSax: move card setup into separate function

* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Kill bogus set_fs(KERNEL_DS) in do_rt_sigreturn().
  [SPARC64]: Update defconfig.
  [SPARC64]: Kill explicit %gl register reference.

* 'uninit-var' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  arch/i386/* fs/* ipc/*: mark variables with uninitialized_var()
  drivers/*: mark variables with uninitialized_var()

* 'warnings' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
  drivers/atm/ambassador: kill uninit'd var warning, and fix bug
  [libata] sata_mv: use pci_try_set_mwi()
  drivers/infiniband/hw/mthca/mthca_qp: kill uninit'd var warning
  drivers/net/wan/sbni: kill uninit'd var warning
  drivers/mtd/ubi/eba: minor cleanup: tighten scope of a local var
  drivers/telephony/ixj: cleanup and fix gcc warning
  drivers/net/wan/pc300_drv: fix bug caught by gcc warning
  drivers/usb/misc/auerswald: fix status check, remove redundant check
  [netdrvr] eepro100, ne2k-pci: abort resume if pci_enable_device() fails
  [netdrvr] natsemi: Fix device removal bug
  kernel/auditfilter: kill bogus uninit'd-var compiler warning

... or we end up with header include order problems from hell.

E.g. on m68k this is 100% fatal - local_irq_enable() there
wants preempt_count(), which wants task_struct fields, which
we won't have when we are in smp.h pulled from sched.h.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>