Take the requested smps mode from the ap params
(instead of always starting with SMPS_OFF)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add feature bits to indicate device support for
static-smps and dynamic-smps modes.

Add a new NL80211_ATTR_SMPS_MODE attribue to allow
configuring the smps mode to be used by the ap
(e.g. configuring to ap to dynamic smps mode will
reduce power consumption while having minor effect
on throughput)
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Correctly mark the network header location in mac80211-generated TDLS
frames. These may be used by lower-level drivers.
Signed-off-by: NArik Nemtsov <arikx.nemtsov@intel.com>
Reviewed-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Userspace might need to know what queues are configured
for uapsd (e.g. for setting proper default values in tspecs).

Add this bitmap to the association event (inside wmm
nested attribute)

Add additional parameter to cfg80211_rx_assoc_resp,
and update its callers.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add nl80211 and driver API to validate, add and delete traffic
streams with appropriate settings.

The API calls for userspace doing the action frame handshake
with the peer, and then allows only to set up the parameters
in the driver. To avoid setting up a session only to tear it
down again, the validate API is provided, but the real usage
later can still fail so userspace must be prepared for that.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Adding a timeout for tearing down a TDLS connection that
hasn't had ACKed traffic sent through it for a certain
amount of time.

Since we have no other monitoring facility to indicate the
existance (or non-existance) of a peer, this patch will
cause a peer to be considered as unavailable if for some X
time at least some Y packets have all not been ACKed.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This patch improves the way minstrel_ht sorts rates according to throughput
and success probability. 3 FOR-loops across the entire rate and mcs group set
in function minstrel_ht_update_stats() which where used to determine the
fastest, second fastest and most robust rate are reduced to 2 FOR-loop.

The sorted list of rates according throughput is extended to the best four
rates as we need them in upcoming joint rate and power control. The sorting
is done via the new function minstrel_ht_sort_best_tp_rates(). The annotation
of those 4 best throughput rates in the debugfs file rc-stats is changes to:
"A,B,C,D", where A is the fastest rate and C the 4th fastest.
Signed-off-by: NThomas Huehn <thomas@net.t-labs.tu-berlin.de>
Tested-by: NStefan Venz <ikstream86@gmail.com>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Minstrel and Mintrel_HT used there own structs to keep track of rate
statistics. Unify those variables in struct minstrel_rate_states and
move it to rc80211_minstrel.h for common usage. This is a clean-up
patch to prepare Minstrel and Minstrel_HT codebase for upcoming TPC.
Signed-off-by: NThomas Huehn <thomas@net.t-labs.tu-berlin.de>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Clear any nl80211 messages that might contain keys after
processing them to avoid leaving their data in memory
"forever" after they've been freed.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There's no need to put the values on the stack, just pass a
pointer to the data in the nl80211 message. This reduces stack
usage and avoids potential issues with putting sensitive data
on the stack.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When freeing the keys stored for wireless extensions, clear the memory
to avoid having the key material stick around in memory "forever".
Similarly, when userspace overwrites a key, actually clear it instead
of just setting the key length to zero.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When freeing the key, clear the memory to avoid having the
key material stick around in memory "forever".
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When freeing the connect keys, clear the memory to avoid
having the key material stick around in memory "forever".
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This message occasionally triggers for some people as in
https://bugzilla.redhat.com/show_bug.cgi?id=1111740 but
it's not clear which (headroom or tailroom) is at fault.
Annotate the message a bit to get more information.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Linux already supports 802.11h, where the access point can tell the
client to reduce its transmission power. However, 802.11h is only
defined for 5 GHz, where the need for this is much smaller than on
2.4 GHz.

Cisco has their own solution, called DTPC (Dynamic Transmit Power
Control). Cisco APs on a controller sometimes but not always send
802.11h; they always send DTPC, even on 2.4 GHz. This patch adds support
for parsing and honoring the DTPC IE in addition to the 802.11h
element (they do not always contain the same limits, so both must
be honored); the format is not documented, but very simple.

Tested (on top of wireless.git and on 3.16.1) against a Cisco Aironet
1142 joined to a Cisco 2504 WLC, by setting various transmit power
levels for the given access points and observing the results.
The Wireshark 802.11 dissector agrees with the interpretation of the
element, except for negative numbers, which seem to never happen
anyway.
Signed-off-by: NSteinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>

Decouple the logic of parsing the 802.11d and 802.11h IEs from the
part of deciding what to do about the data (messaging, clamping to
0 dBm, doing the actual setting). This paves the way for the next
patch, which introduces more data sources for transmit power limitation.
Signed-off-by: NSteinar H. Gunderson <sgunderson@bigfoot.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

commit "mac80211: disable 40MHz support in case of 20MHz AP"
broke working VHT in 20Mhz with APs like Netgear R6300v2 which
do not publish support for 40Mhz but allow use of VHT in 20Mhz.
The break is because VHT is disabled once no HT cap doesn't indicate
support for 40Mhz. This causes the assoc request to be sent without
any VHT IE and the association is only HT due to this.

For more details check out commit 4a817aa7
"mac80211: allow VHT with peers not capable of 40MHz"

Fixes: 53b954ee ("mac80211: disable 40MHz support in case of 20MHz AP")
Signed-off-by: NEyal Shapira <eyalx.shapira@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Extend mac80211 set_coverage_class API in order to enable ACK timeout
estimation algorithm (dynack) passing coverage class equals to -1
to lower drivers. Synchronize set_coverage_class routine signature with
mac80211 function pointer for p54, ath9k, ath9k_htc and ath5k drivers.
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Enable ACK timeout estimation algorithm (dynack) using mac80211
set_coverage_class API. Dynack is activated passing coverage class equals to -1
to lower drivers and it is automatically disabled setting valid value for
coverage class.
Define NL80211_ATTR_WIPHY_DYN_ACK flag attribute to enable dynack from
userspace. In order to activate dynack NL80211_FEATURE_ACKTO_ESTIMATION feature
flag must be set by lower drivers to indicate dynack capability.
Signed-off-by: NLorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

If the remaining time in the current roc is not long
enough, mac80211 adds the new roc right after it
(if they have similar params).

However, in case of multiple rocs, the "next roc"
is not considered, resulting in multiple rocs,
each one with its own duration.

Refactor the code a bit and consider the next roc,
so a single max roc will be used instead of
multiple rocs (which might last much longer).
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The new duration (remaining duration after the current
ROC ends) was calculated but not used, making the
optimization worthless.
Signed-off-by: NEliad Peller <eliadx.peller@intel.com>
Reviewed-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The regdom intersection code simply tries intersecting
each rule of the source with each rule of the target.

Since the resulting intersections are not observed
as a whole, this can result in multiple overlapping/duplicate
entries.

Make the rule addition a bit more smarter, by looking
for rules that can be contained within other rules,
and adding only extended ones.
Signed-off-by: NEliad Peller <eliad@wizery.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

In case of a RRM-supporting connection, in the association request
frame: set the RRM capability flag, and add the required IEs.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Add a flag attribute to use in associations, for tagging the target
connection as supporting RRM. It is the responsibility of upper
layers to set this flag only if both the underlying device, and the
target network indeed support RRM.
To be used in ASSOCIATE and CONNECT commands.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Radio Resource Measurement (RRM) is a bundle of features which will
require the entire stack to participate.
In this patch, the driver is given the opportunity to advertise the
device's support for these RRM-related features, using feature flags:
1. Support for Quiet IEs.
2. Support for adding DS Parameter Set IE to probe requests.
3. Support for adding WFA TPC Report IE to probe requests.
4. Support for inserting tx power value to tx-ed packets at a fixed
   offset. This is used in action frames, such as RRM's Link
   Measurement Report, where the actual tx power should be reported
   in the frame.
Signed-off-by: NAssaf Krauss <assaf.krauss@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The function description claimed that on error the skb isn't
freed even though it is, and stated return values that are
different than what really happens in the code.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.

For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Our legal structure changed at some point (see wikipedia), but
we forgot to immediately switch over to the new copyright
notice.

For files that we have modified in the time since the change,
add the proper copyright notice now.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Not sure how the declaration of ieee80211_tdls_peer_del_work
landed after the double inclusion protection end.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When starting an offloaded BA session it is
unknown what starting sequence number should be
used. Using last_seq worked in most cases except
after hw restart.

When hw restart is requested last_seq is
(rightfully so) kept unmodified. This ended up
with BA sessions being restarted with an aribtrary
BA window values resulting in dropped frames until
sequence numbers caught up.

Instead of last_seq pick seqno of a first Rxed
frame of a given BA session.

This fixes stalled traffic after hw restart with
offloaded BA sessions (currently only ath10k).
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This adds one more ACPI ID of a Broadcom bluetooth chip.
Signed-off-by: NMika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When a device driver is unloaded local->interfaces
list is cleared. If there was more than 1
interface running and connected (bound to a
chanctx) then chantype recalc was called and it
ended up with compat being NULL causing a call
trace warning.

Warn if compat becomes NULL as a result of
incompatible bss_conf.chandef of interfaces bound
to a given channel context only.

The call trace looked like this:

 WARNING: CPU: 2 PID: 2594 at /devel/src/linux/net/mac80211/chan.c:557 ieee80211_recalc_chanctx_chantype+0x2cd/0x2e0()
 Modules linked in: ath10k_pci(-) ath10k_core ath
 CPU: 2 PID: 2594 Comm: rmmod Tainted: G        W     3.16.0-rc1+ #150
 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
  0000000000000009 ffff88001ea279c0 ffffffff818dfa93 0000000000000000
  ffff88001ea279f8 ffffffff810514a8 ffff88001ce09cd0 ffff88001e03cc58
  0000000000000000 ffff88001ce08840 ffff88001ce09cd0 ffff88001ea27a08
 Call Trace:
  [<ffffffff818dfa93>] dump_stack+0x4d/0x66
  [<ffffffff810514a8>] warn_slowpath_common+0x78/0xa0
  [<ffffffff81051585>] warn_slowpath_null+0x15/0x20
  [<ffffffff818a407d>] ieee80211_recalc_chanctx_chantype+0x2cd/0x2e0
  [<ffffffff818a3dda>] ? ieee80211_recalc_chanctx_chantype+0x2a/0x2e0
  [<ffffffff818a4919>] ieee80211_assign_vif_chanctx+0x1a9/0x770
  [<ffffffff818a6220>] __ieee80211_vif_release_channel+0x70/0x130
  [<ffffffff818a6dd3>] ieee80211_vif_release_channel+0x43/0xb0
  [<ffffffff81885f4e>] ieee80211_stop_ap+0x21e/0x5a0
  [<ffffffff8184b9b5>] __cfg80211_stop_ap+0x85/0x520
  [<ffffffff8181c188>] __cfg80211_leave+0x68/0x120
  [<ffffffff8181c268>] cfg80211_leave+0x28/0x40
  [<ffffffff8181c5f3>] cfg80211_netdev_notifier_call+0x373/0x6b0
  [<ffffffff8107f965>] notifier_call_chain+0x55/0x110
  [<ffffffff8107fa41>] raw_notifier_call_chain+0x11/0x20
  [<ffffffff816a8dc0>] call_netdevice_notifiers_info+0x30/0x60
  [<ffffffff816a8eb9>] __dev_close_many+0x59/0xf0
  [<ffffffff816a9021>] dev_close_many+0x81/0x120
  [<ffffffff816aa1c5>] rollback_registered_many+0x115/0x2a0
  [<ffffffff816aa3a6>] unregister_netdevice_many+0x16/0xa0
  [<ffffffff8187d841>] ieee80211_remove_interfaces+0x121/0x1b0
  [<ffffffff8185e0e6>] ieee80211_unregister_hw+0x56/0x110
  [<ffffffffa0011ac4>] ath10k_mac_unregister+0x14/0x60 [ath10k_core]
  [<ffffffffa0014fe7>] ath10k_core_unregister+0x27/0x40 [ath10k_core]
  [<ffffffffa003b1f4>] ath10k_pci_remove+0x44/0xa0 [ath10k_pci]
  [<ffffffff81373138>] pci_device_remove+0x28/0x60
  [<ffffffff814cb534>] __device_release_driver+0x64/0xd0
  [<ffffffff814cbcc8>] driver_detach+0xb8/0xc0
  [<ffffffff814cb23a>] bus_remove_driver+0x4a/0xb0
  [<ffffffff814cc697>] driver_unregister+0x27/0x50
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The "rcu_dereference()" calls are used directly in conditions.
Since their return values are never dereferenced it is recommended to
use "rcu_access_pointer()" instead of "rcu_dereference()".
Therefore, this patch makes the replacements.

The following Coccinelle semantic patch was used:
@@
@@

(
 if(
 (<+...
- rcu_dereference
+ rcu_access_pointer
  (...)
  ...+>)) {...}
|
 while(
 (<+...
- rcu_dereference
+ rcu_access_pointer
  (...)
  ...+>)) {...}
)
Signed-off-by: NAndreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

The use of "rcu_assign_pointer()" is NULLing out the pointer.
According to RCU_INIT_POINTER()'s block comment:
"1.   This use of RCU_INIT_POINTER() is NULLing out the pointer"
it is better to use it instead of rcu_assign_pointer() because it has a
smaller overhead.

The following Coccinelle semantic patch was used:
@@
@@

- rcu_assign_pointer
+ RCU_INIT_POINTER
  (..., NULL)
Signed-off-by: NAndreea-Cristina Bernat <bernat.ada@gmail.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When using the cfg80211_inform_bss[_width]() functions drivers
cannot currently indicate whether the data was received in a
beacon or probe response. Fix that by passing a new enum that
indicates such (or unknown).

For good measure, use it in ath6kl.

Acked-by: Kalle Valo <kvalo@qca.qualcomm.com> [ath6kl]
Acked-by: Arend van Spriel <arend@broadcom.com> [brcmfmac]
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

There are a few possible cases of where BSS data came from:
 1) only a beacon has been received
 2) only a probe response has been received
 3) the driver didn't report what it received (this happens when
    using cfg80211_inform_bss[_width]())
 4) both probe response and beacon data has been received

Unfortunately, in the userspace API, a few things weren't there:
 a) there was no way to differentiate cases 1) and 4) above
    without comparing the data of the IEs
 b) the TSF was always from the last frame, instead of being
    exposed for beacon/probe response separately like IEs

Fix this by
   i) exporting a new flag attribute that indicates whether or
      not probe response data has been received - this addresses (a)
  ii) exporting a BEACON_TSF attribute that holds the beacon's TSF
      if a beacon has been received
 iii) not exporting the beacon attributes in case (3) above as that
      would just lead userspace into thinking the data actually came
      from a beacon when that isn't clear

To implement this, track inside the IEs struct whether or not it
(definitely) came from a beacon.

Reported-by: William Seto
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

This reverts commit dda444d5.

Channel switching code has been reworked and
improved significantly since the time original
locking issues were found.
Signed-off-by: NMichal Kazior <michal.kazior@tieto.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

Header-less cloned skbs with sufficient headroom need not be cloned
unless the tailroom is going to be modified.

Fix ieee80211_skb_resize so it would only resize cloned skbs if either
the header isn't released or the tailroom is going to be modified.

Some drivers might have assumed that skbs are never cloned, so add a HW
flag that explicitly permits cloned TX skbs. Drivers which do not modify
TX skbs should set this flag to avoid copying skbs.
Signed-off-by: NIdo Yariv <idox.yariv@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

When hw acceleration is enabled, the GENERATE_IV or PUT_IV_SPACE flags
will only require headroom space. Consequently, the tailroom-needed
counter can safely be decremented.
Signed-off-by: NIdo Yariv <idox.yariv@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>

TPC report element is contained in spectrum management's tpc report
action frames and in radio measurement's link measurement report
action frames. Add a function which checks whether an action frame
contains this element. This may be needed by the drivers in order
to set the correct tx power value in these frames.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>