split __bpf_prog_run() interpreter into stack allocation and execution parts.
The code section shrinks which helps interpreter performance in some cases.
   text	   data	    bss	    dec	    hex	filename
  26350	  10328	    624	  37302	   91b6	kernel/bpf/core.o.before
  25777	  10328	    624	  36729	   8f79	kernel/bpf/core.o.after

Very short programs got slower (due to extra function call):
Before:
test_bpf: #89 ALU64_ADD_K: 1 + 2 = 3 jited:0 7 PASS
test_bpf: #90 ALU64_ADD_K: 3 + 0 = 3 jited:0 8 PASS
test_bpf: #91 ALU64_ADD_K: 1 + 2147483646 = 2147483647 jited:0 7 PASS
test_bpf: #92 ALU64_ADD_K: 4294967294 + 2 = 4294967296 jited:0 11 PASS
test_bpf: #93 ALU64_ADD_K: 2147483646 + -2147483647 = -1 jited:0 7 PASS
After:
test_bpf: #89 ALU64_ADD_K: 1 + 2 = 3 jited:0 11 PASS
test_bpf: #90 ALU64_ADD_K: 3 + 0 = 3 jited:0 11 PASS
test_bpf: #91 ALU64_ADD_K: 1 + 2147483646 = 2147483647 jited:0 11 PASS
test_bpf: #92 ALU64_ADD_K: 4294967294 + 2 = 4294967296 jited:0 14 PASS
test_bpf: #93 ALU64_ADD_K: 2147483646 + -2147483647 = -1 jited:0 10 PASS

Longer programs got faster:
Before:
test_bpf: #266 BPF_MAXINSNS: Ctx heavy transformations jited:0 20286 20513 PASS
test_bpf: #267 BPF_MAXINSNS: Call heavy transformations jited:0 31853 31768 PASS
test_bpf: #268 BPF_MAXINSNS: Jump heavy test jited:0 9815 PASS
test_bpf: #269 BPF_MAXINSNS: Very long jump backwards jited:0 6 PASS
test_bpf: #270 BPF_MAXINSNS: Edge hopping nuthouse jited:0 13959 PASS
test_bpf: #271 BPF_MAXINSNS: Jump, gap, jump, ... jited:0 210 PASS
test_bpf: #272 BPF_MAXINSNS: ld_abs+get_processor_id jited:0 21724 PASS
test_bpf: #273 BPF_MAXINSNS: ld_abs+vlan_push/pop jited:0 19118 PASS
After:
test_bpf: #266 BPF_MAXINSNS: Ctx heavy transformations jited:0 19008 18827 PASS
test_bpf: #267 BPF_MAXINSNS: Call heavy transformations jited:0 29238 28450 PASS
test_bpf: #268 BPF_MAXINSNS: Jump heavy test jited:0 9485 PASS
test_bpf: #269 BPF_MAXINSNS: Very long jump backwards jited:0 12 PASS
test_bpf: #270 BPF_MAXINSNS: Edge hopping nuthouse jited:0 13257 PASS
test_bpf: #271 BPF_MAXINSNS: Jump, gap, jump, ... jited:0 213 PASS
test_bpf: #272 BPF_MAXINSNS: ld_abs+get_processor_id jited:0 19389 PASS
test_bpf: #273 BPF_MAXINSNS: ld_abs+vlan_push/pop jited:0 19583 PASS

For real world production programs the difference is noise.

This patch is first step towards reducing interpreter stack consumption.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

free up BPF_JMP | BPF_CALL | BPF_X opcode to be used by actual
indirect call by register and use kernel internal opcode to
mark call instruction into bpf_tail_call() helper.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: move BPF offload code into app

This series moves the eBPF offload code out of netdev/vNIC handling and
starts building the nfp_app.  Port init is moved into the apps as well
because various apps associate vNICs, representors with ports differently.

First patch adds a helper for updating tc stats which has been waiting
in my tree to be included in any moderately related series.

Next series will bring communicating with FW using control messages,
then representors, BPF maps, tc flower... :)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Free management FW info when app FW load failed.

Fixes: eefbde7e ("nfp: add hwmon support")
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow apps to associate private data with vNICs and move
BPF-specific fields of nfp_net to such structure.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Move bulk of the eBPF offload code out of common vNIC code into
app-specific callbacks.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pure move of eBPF offload files to BPF app directory,
only change the names and relative header location.
nfp_asm.h stays in the main dir and it doesn't really
have to include nfp_bpf.h.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Let the app print its name in ethtool -i output.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Start fleshing out the apps by turning the vNIC init code to
a per-app callback.  The two initial apps we have are NIC and
eBPF.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Turn the function to read number of ports into a generic helper.
While at it make sure we propagate all errors other than -ENOENT.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GCC 7 checks for fall through comments, add the two missing ones.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Forgetting to disable preemption around tcf_action_stats_update()
seems to be a common mistake.  Add a helper function for updating
stats on all actions of a filter.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
10GbE Intel Wired LAN Driver Updates 2017-05-31

This series contains updates to ixgbe and ixgbevf only.

Scott enables support for TSO & GSO for MPLS encapsulated packets for both
ixgbe and ixgbevf.

Liwei Song fixes an issue where seqcount/seqlock in ixgbe_get_stats64()
are not initialized in time, so move the initialization into probe routine
after the transmit and receive rings are initialized.

Paul cleans up led_[on|off] for X550EM_X, since the firmware configures
the PHY & MAC and we have no PHY access so LED on/off is not supported
with this device.

Emil provides several fixes, starting with enabling RSS on VF to VF
traffic on the same PF.  Fixed PHY identification, where the previous
method was unreliable, so use a different register to ensure proper
identification.  Cleaned up the logic which could cause us to
skip the link configuration, this skipping over the link configuration
was leaving SFP+ PHY's in an unstable state, so always call
setup_mac_link().  Added RS1 (rate select 1) support for ixgbe.  Lastly,
fixed incorrect logic in the setting up of SFP+ link speed.

Mark fixes the thermal sensor event logic, where it was being executed
when there really was no thermal event.  So simplify the logic to only
execute when there is a thermal event.

Tony adds additional error checks and reporting when setting a VF MAC
address to ensure that the MAC filter was successfully added.  Also
fixed possible truncation warnings, as well as implicit fallthrough
warnings.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
40GbE Intel Wired LAN Driver Updates 2017-05-31

This series contains updates to i40e and i40evf only.

Jesse provides a couple of fixes, starting with cleaning up duplicate
lines of code.  Fixed a missing line which enables RSS as a negotiated
feature.  Since the VF does not have any way of reporting FCoE enabled,
so just force the code to always report FCoE as disabled.

Jake provides several fixes and changes, starting with fixing a race
condition in i40e.  The hardware has a limitation on transmit PTP packets,
which requires us to limit the driver to timestamping a single packet at
once.  This is done using a state bitlock which enforces that only one
timestamp request is honored at a time, unfortunately this suffers from
a race condition.  Fixed a corner case where we failed to cleanup the
bit lock after a failed transmit, and resulted in a state bit being
locked forever.  Added a new statistic which tracks when a transmit
timestamp request is skipped/ignored, since the driver can only handle
one transmit timestamp request at a time.

Christophe Jaillet fixes a NULL pointer dereference if kzalloc fails.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add direct #include statements for declarations of csum_tcpudp_magic()
and csum_ipv6_magic().  While the needed #include's are picked up
indirectly for the x86 architecture, they aren't on other
architectures, resulting in compile errors.
Signed-off-by: NMichael Kelley <mikelley@microsoft.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Small clean-up to rtmsg_ifinfo() to use the rtnl_get_event()
interface instead of using 'internal' values directly.
Signed-off-by: NVladislav Yasevich <vyasevic@redhat.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

An eBPF ELF file generated with LLVM can contain several program
section, which can be used for bpf tail calls.  The bpf prog file
descriptors are accessible via array prog_fd[].

At-least XDP samples assume ordering, and uses prog_fd[0] is the main
XDP program to attach.  The actual order of array prog_fd[] depend on
whether or not a bpf program section is referencing any maps or not.
Not using a map result in being loaded/processed after all other
prog section.  Thus, this can lead to some very strange and hard to
debug situation, as the user can only see a FD and cannot correlated
that with the ELF section name.

The fix is rather simple, and even removes duplicate memcmp code.
Simply load program sections as the last step, instead of
load_and_attach while processing the relocation section.

When working with tail calls, it become even more essential that the
order of prog_fd[] is consistant, like the current dependency of the
map_fd[] order.
Signed-off-by: NJesper Dangaard Brouer <brouer@redhat.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new mlxfw code fails to build without the xz library:

drivers/net/ethernet/mellanox/mlxfw/mlxfw_mfa2.o: In function `mlxfw_mfa2_xz_dec_run':
:(.text.mlxfw_mfa2_xz_dec_run+0x8): undefined reference to `xz_dec_run'
drivers/net/ethernet/mellanox/mlxfw/mlxfw_mfa2.o: In function `mlxfw_mfa2_file_component_get':
:(.text.mlxfw_mfa2_file_component_get+0x218): undefined reference to `xz_dec_init'
:(.text.mlxfw_mfa2_file_component_get+0x2c0): undefined reference to `xz_dec_end'

This adds a Kconfig 'select' statement for it, which is also what
the other user of that library has.

Fixes: 410ed13c ("Add the mlxfw module for Mellanox firmware flash process")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current dsa_register_switch function takes a useless struct device
pointer argument, which always equals ds->dev.

Drivers either call it with ds->dev, or with the same device pointer
passed to dsa_switch_alloc, which ends up being assigned to ds->dev.

This patch removes the second argument of the dsa_register_switch and
_dsa_register_switch functions.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vivien Didelot says:

====================
net: dsa: mv88e6xxx: PHY nitpicks

This patchset isolates more PPU code into phy.c and makes distinction
between PHY Registers read and write implementations vs. generic PHY
routines.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Respect the implicit naming convention used in all register sets
specific files, by renaming the mv88e6xxx_ppu_* functions with the
mv88e6xxx_phy_* prefix.

This is simply a s/xxx_ppu/xxx_phy_ppu/ substitution.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make it clear that mv88e6xxx_phy_ppu_{read,write} are an implementation
of the .phy_{read,write} operations, by renaming them with the mv88e6185
prefix, since 88E6185 it is the reference switch model supported in an
upstream board (ZII Dev Rev B), which makes use of them.

Distinguish the signatures of implementation specific and generic PHY
functions in the phy.h header.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Similarly to the VTU, PVT and ATU setup, provide a mv88e6xxx_phy_setup
helper which wraps mv88e6xxx_ppu_enable, so that no more PPU-related
functions are exposed outside of phy.c.

Thus make mv88e6xxx_ppu_enable static.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Check for ret_val instead of !ret_val to allow the rest of
the code to execute and configure the speed properly.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add RS1 configuration to ixgbe_set_soft_rate_select_speed()
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove the logic which would previously skip the link configuration
in the case where we are already at the requested speed in
ixgbe_setup_mac_link_multispeed_fiber().

By exiting early we are skipping the link configuration and as such
the driver may not always configure the PHY correctly for SFP+.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Make sure the writes are processed immediately. Without the flush it
is possible for operations on one port to spill over the other as the
resource is shared.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Previous method was unreliable. Use a different register to
differentiate between the SKUs.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Additions to gcc 7 now warn whenever a switch statement falls through
implicitly.  This patch adds explicit fall through comments to address the
following warnings:

drivers/net/ethernet/intel/ixgbevf/vf.c: In function ‘ixgbevf_get_reta_locked’:
drivers/net/ethernet/intel/ixgbevf/vf.c:336:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (hw->mac.type < ixgbe_mac_X550_vf)
      ^
drivers/net/ethernet/intel/ixgbevf/vf.c:338:2: note: here
  default:
  ^~~~~~~
drivers/net/ethernet/intel/ixgbevf/vf.c: In function ‘ixgbevf_get_rss_key_locked’:
drivers/net/ethernet/intel/ixgbevf/vf.c:402:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
   if (hw->mac.type < ixgbe_mac_X550_vf)
      ^
drivers/net/ethernet/intel/ixgbevf/vf.c:404:2: note: here
  default:
  ^~~~~~~
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The following warning is now shown as a result of new checks added for
gcc 7:

drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c: In function ‘ixgbevf_open’:
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:1363:13: warning: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size between 3 and 18 [-Wformat-truncation=]
      "%s-%s-%d", netdev->name, "TxRx", ri++);
             ^~
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:1363:6: note: directive argument in the range [0, 2147483647]
      "%s-%s-%d", netdev->name, "TxRx", ri++);
      ^~~~~~~~~~
drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c:1362:4: note: ‘snprintf’ output between 8 and 32 bytes into a destination of size 24
    snprintf(q_vector->name, sizeof(q_vector->name) - 1,
    ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      "%s-%s-%d", netdev->name, "TxRx", ri++);
      ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Resolve this warning by making a couple of changes.
 - Don't reserve space for the null terminator.  Since snprintf adds the
   null terminator automatically, there is no need for us to reserve a byte
   for it.

 - Change a couple variables that can never be negative from int to
   unsigned int.

While we're making changes to the format string, move the constant strings
into the format string instead of providing them as specifiers.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds/changes fall through comments to address new warnings
produced by gcc 7.

Fixed formatting on a couple of comments in the function.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The following warning is now shown as a result of new checks added for
gcc 7:

drivers/net/ethernet/intel/ixgbe/ixgbe_main.c: In function ‘ixgbe_open’:
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:3118:13: warning: ‘%d’ directive output may be truncated writing between 1 and 10 bytes into a region of size between 3 and 18 [-Wformat-truncation=]
      "%s-%s-%d", netdev->name, "TxRx", ri++);
             ^~
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:3118:6: note: directive argument in the range [0, 2147483647]
      "%s-%s-%d", netdev->name, "TxRx", ri++);
      ^~~~~~~~~~
drivers/net/ethernet/intel/ixgbe/ixgbe_main.c:3117:4: note: ‘snprintf’ output between 8 and 32 bytes into a destination of size 24
    snprintf(q_vector->name, sizeof(q_vector->name) - 1,
    ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
      "%s-%s-%d", netdev->name, "TxRx", ri++);
      ~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~

Resolve this warning by making a couple of changes.
 - Don't reserve space for the null terminator.  Since snprintf adds the
   null terminator automatically, there is no need for us to reserve a byte
   for it.

 - Change a couple variables that can never be negative from int to
   unsigned int.

While we're making changes to the format string, move the constant strings
into the format string instead of providing them as specifiers.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently, when setting a VF MAC address there are no error checks to
ensure that the MAC filter was successfully added.  This patch adds
additional error checks, reporting, and propagation of errors.  It also
will not set the MAC address unless adding the MAC filter was successful.

With these changes, setting the mac address to zeros can no longer call
ixgbe_set_vf_mac() as adding a zero MAC address filter is not valid.
Instead directly delete the filter and, if successful, clear the MAC
address.
Signed-off-by: NTony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The thermal sensor event logic is messed up, because it can execute
the code when there is no thermal event. The current logic is that
it will exit when !capable && !event whereas it really should exit
when !capable || !event. For one thing, it means that the service
task is doing too much work. It probably has some other symptoms as
well. So, correct the logic, simplifying to only execute when there
is a thermal event. The capable check is redundant.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This will ensure that VF-to-VF traffic on the same PF
is filtered to allow RSS operation.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since FW configures the PHY and MAC X550EM_X has no
PHY access, led_[on|off] is not supported with the 1Gbase-t design.

Removed MAC X550EM_X 1Gbase-t led_[on|off] support by setting
function pointers to NULL and added NULL pointer checks. Also set
init_led_link_act to NULL and added NULL pointer check.
Signed-off-by: NPaul Greenwalt <paul.greenwalt@intel.com>
Tested-by: NKrishneil Singh <krishneil.k.singh@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fix the following CallTrace:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 71 PID: 1 Comm: swapper/0 Not tainted 4.8.8-WR9.0.0.1_standard #11
Hardware name: Intel Corporation S2600WTT/S2600WTT,
BIOS GRNDSDP1.86B.0036.R05.1407140519 07/14/2014
 00200086 00200086 eb5e1ab8 c144dd70 00000000 00000000 eb5e1af8 c10af89a
 c1d23de4 eb5e1af8 00000009 eb5d8600 eb5d8638 eb5e1af8 c10b14d8 00000009
 0000000a c1d32911 00000000 00000000 e44c826c eb5d8000 eb5e1b74 c10b214e
Call Trace:
 [<c144dd70>] dump_stack+0x5f/0x8f
 [<c10af89a>] register_lock_class+0x25a/0x4c0
 [<c10b14d8>] ? check_irq_usage+0x88/0xc0
 [<c10b214e>] __lock_acquire+0x5e/0x17a0
 [<c1abdb9b>] ? _raw_spin_unlock_irqrestore+0x3b/0x70
 [<c10cf14a>] ? rcu_read_lock_sched_held+0x8a/0x90
 [<c10b3c5f>] lock_acquire+0x9f/0x1f0
 [<c1922dcf>] ? dev_get_stats+0x5f/0x110
 [<c176e6b3>] ixgbe_get_stats64+0x113/0x320
 [<c1922dcf>] ? dev_get_stats+0x5f/0x110
 [<c1922dcf>] dev_get_stats+0x5f/0x110
 [<c1ab5415>] rtnl_fill_stats+0x40/0x105
 [<c193dd45>] rtnl_fill_ifinfo+0x4c5/0xd20
 [<c11c5115>] ? __kmalloc_node_track_caller+0x1a5/0x410
 [<c1917487>] ? __kmalloc_reserve.isra.42+0x27/0x80
 [<c191754f>] ? __alloc_skb+0x6f/0x270
 [<c1942291>] rtmsg_ifinfo_build_skb+0x71/0xd0
 [<c194230a>] rtmsg_ifinfo.part.23+0x1a/0x50
 [<c1923dad>] ? call_netdevice_notifiers_info+0x2d/0x60
 [<c194236b>] rtmsg_ifinfo+0x2b/0x40
 [<c192f997>] register_netdevice+0x3d7/0x4d0
 [<c192faa7>] register_netdev+0x17/0x30
 [<c177b83d>] ixgbe_probe+0x118d/0x1610
 [<c1498202>] local_pci_probe+0x32/0x80
 [<c1498172>] ? pci_match_device+0xd2/0x100
 [<c14991e0>] pci_device_probe+0xc0/0x110
 [<c1652cc5>] driver_probe_device+0x1c5/0x280
 [<c1498172>] ? pci_match_device+0xd2/0x100
 [<c1652e09>] __driver_attach+0x89/0x90
 [<c1652d80>] ? driver_probe_device+0x280/0x280
 [<c165114f>] bus_for_each_dev+0x4f/0x80
 [<c165269e>] driver_attach+0x1e/0x20
 [<c1652d80>] ? driver_probe_device+0x280/0x280
 [<c1652317>] bus_add_driver+0x1a7/0x220
 [<c1653a79>] driver_register+0x59/0xe0
 [<c1f897b8>] ? igb_init_module+0x49/0x49
 [<c1497b2a>] __pci_register_driver+0x4a/0x50
 [<c1f8985d>] ixgbe_init_module+0xa5/0xc4
 [<c1000485>] do_one_initcall+0x35/0x150
 [<c107e818>] ? parameq+0x18/0x70
 [<c1f395d8>] ? repair_env_string+0x12/0x51
 [<c107ead0>] ? parse_args+0x260/0x3b0
 [<c1074f73>] ? __usermodehelper_set_disable_depth+0x43/0x50
 [<c1f39e90>] kernel_init_freeable+0x19b/0x267
 [<c1f395c6>] ? set_debug_rodata+0xf/0xf
 [<c10b1e7b>] ? trace_hardirqs_on+0xb/0x10
 [<c1abdc02>] ? _raw_spin_unlock_irq+0x32/0x50
 [<c1085f0b>] ? finish_task_switch+0xab/0x1f0
 [<c1085ec9>] ? finish_task_switch+0x69/0x1f0
 [<c1ab6a30>] kernel_init+0x10/0x110
 [<c108bd65>] ? schedule_tail+0x25/0x80
 [<c1abe422>] ret_from_kernel_thread+0xe/0x24
 [<c1ab6a20>] ? rest_init+0x130/0x130

This CallTrace occurred on 32-bit kernel with CONFIG_PROVE_LOCKING
enabled.

This happens at ixgbe driver probe hardware stage, when comes to
ixgbe_get_stats64, the seqcount/seqlock still not initialize, although
this was initialize in TX/RX resources setup routin, but it was too late,
then lockdep give this Warning.

To fix this, move the u64_stats_init function to driver probe stage,
which before we get the status of seqcount and after the RX/TX ring
was finished init.
Signed-off-by: NLiwei Song <liwei.song@windriver.com>
Tested-by: NKrishneil Singh  <krishneil.k.singh@intel.com>

This patch advertises TSO & GSO features in netdev->mpls_features.
In ixgbe(vf)_tso() where we set up segmentation offload, the IP
header will be the inner network header when eth_p_mpls() indicates
the Ethernet protocol is MPLS (UC or MC).
Suggested-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NScott Peterson <scott.d.peterson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If 'kzalloc' fails, a NULL pointer will be dereferenced. Return -ENOMEM
instead.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The i40e driver has logic to handle only one Tx timestamp at a time,
using a state bit lock to avoid multiple requests at once.

It may be possible, if incredibly unlikely, that a Tx timestamp event is
requested but never completes. Since we use an interrupt scheme to
determine when the Tx timestamp occurred we would never clear the state
bit in this case.

Add an i40e_ptp_tx_hang() function similar to the already existing
i40e_ptp_rx_hang() function. This function runs in the watchdog routine
and makes sure we eventually recover from this case instead of
permanently disabling Tx timestamps.

Note: there is no currently known way to cause this without hacking the
driver code to force it.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>