On Broadcom ARM routers BCM4366 cards are available with 14e4:4365 ID.
Unfortunately this ID was already used by Broadcom for cards with
BCM43142, a totally different chipset requiring SoftMAC driver. To avoid
a conflict between brcmfmac and bcma use more specific ID entry with
subvendor and subdevice specified.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On recent Broadcom chipsets PMU is present as separated core and it
can't be accessed using ChipCommon anymore as it fails with e.g.:
[   18.198412] Unhandled fault: imprecise external abort (0x1406) at 0xb6da200f

Add a new helper function that will return a proper core that should be
used for accessing PMU registers.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is an extra bitfield with info about some present hardware.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Separated PMU core can be found in new devices and should be used for
accessing PMU registers (which were routed through ChipCommon so far).
This core is one of exceptions that doesn't have or need wrapper address
to be still safely accessible.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

So far we were looking for address descriptors without a check for
crossing current component border. In case of dealing with unsupported
descriptor or descriptor missing at all the code would incorrectly get
data from another component.

Consider this binary-described component from BCM4366 EROM:
4bf83b01	TAG==CI		CID==0x83b
20080201	TAG==CI		PORTS==0+1	WRAPPERS==0+1
18400035	TAG==ADDR	SZ_SZD		TYPE_SLAVE
00050000
18107085	TAG==ADDR	SZ_4K		TYPE_SWRAP

Driver was assigning invalid base address to this core:
brcmfmac:  [6 ] core 0x83b:32 base 0x18109000 wrap 0x18107000
which came from totally different component defined in EROM:
43b36701	TAG==CI		CID==0x367
00000201	TAG==CI		PORTS==0+1	WRAPPERS==0+0
18109005	TAG==ADDR	SZ_4K		TYPE_SLAVE

This change will also allow us to support components without wrapper
address in the future.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It seems 14e4:4365 pattern is too generic as there are two devices:
1) 14e4:4365 1028:0016 with SoftMAC BCM43142 chipset
2) 14e4:4365 14e4:4365 with FullMAC BCM4366 chipset
The later one was found in D-Link DIR-885L router and we want to let
brcmfmac handle it.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It's another SoC with 32 GPIOs and simplified watchdog handling. It was
tested on D-Link DIR-885L.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

UART is connected to and controlled over ChipCommon core. It doesn't
have much to do with MIPS core (where we initialize it currently)
except just existing on embedded systemms. There isn't point of such
cross-core initialization (and we needed #ifdef anyway) so just handle
it in ChipCommon.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

First of all it changes the way we calculate primary channel offset. If
we use e.g. 80 MHz channel with primary frequency 5180 MHz (which means
center frequency is 5210 MHz) it makes sense to calculate primary offset
as -30 MHz.
Then it fixes values we compare primary_offset with. We were comparing
offset in MHz against -2 or 2 which was resulting in picking a wrong
primary channel.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

On recent Broadcom chipsets PMU is present as separated core and it
can't be accessed using ChipCommon anymore as it fails with e.g.:
[    0.000577] Unhandled fault: external abort on non-linefetch (0x1008) at 0xf1000604

Solve it by using a new (PMU) core pointer set to ChipCommon or PMU
depending on the hardware capabilities.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

PMU (Power Management Unit) seems to be a separated piece of hardware,
just accessed using ChipCommon core registers. In recent Broadcom
chipsets PMU is not bounded to CC but available as separated core.

To make code cleaner & easier to review (for a correct R/W access) use
clearer names.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Both cores are another exceptions. They are not accessed in a standard
way and to they don't need or have wrapping addresses.
This fixes bus scanning after finding such core.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add missing defines and print proper names.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

It's a Macronix 32 MiB flash found on board with BCM47189 SoC.
Signed-off-by: NRafał Miłecki <zajec5@gmail.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Merge tag 'iwlwifi-next-for-kalle-2016-01-31_2' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

Here's a first batch of patches for 4.6:
* continue the work on multiple Rx queues (Sara)
* add support for beacon storing
  used in low power states (Sara)
* cleanups (Rodrigo, Johannes)
* fix the LED behavior for iwldvm (Hubert)
* Use the regular firmware image of WoWLAN (Matti)
* fix 8000 devices for Big Endian machines (Johannes)
* more firmware debug hooks (Golan)
* add support for P2P Client snoozing (Avri)
* make the beacon filtering for AP mode configurable (Andrei)
* fix transmit queues overflow with LSO

When in AP mode we need to filter in beacons from other APs to update HT
operation mode. As a power optimization the beacons are filtered out when
there are no associated stations. As a result, when there are no
associated stations, we will not update the HT operation mode until a
station connects.
Add a debugfs parameter that allows to disable this optimization.
Signed-off-by: NAndrei Otcheretianski <andrei.otcheretianski@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Final API of iwl_mpdu_desc has a change in the order of
the fields and does not include energy from the third
antenna (which is perfectly fine, since we don't have one).
Update the structure accordingly.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Previous patches enabled new 9000 hardware DMA for one queue
only.
Enable the actual multi-queue path and configuration now.
This requires also per-queue NAPI struct.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

9000 series supports multi-queue rx. The hardware needs
to be configured with the hash functions to perform and
indirection table that maps hash results to the relevant
CPUs\queues.
Support this configuration.
Add debugfs hook to configure the indirection table in
order to enable performance analysis. The configuration
is stateless, receives a partial or full pattern and sends
the command to the firmware.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Decreasing Tx power is allowed only when success ratio is
above the threshold defined in the algorithm. Add this condition.
Signed-off-by: NGregory Greenman <gregory.greenman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The 9000 hardware introduces the frame releaser, which
keeps track of the aggregation window and notifies host
of the window status. This requires in turn updating
the hardware with the RX BA session window size.
Firmware API was changed to enable that, update the driver
accordingly.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

It is only called from iwl_mvm_power_set_ba() so simplify things
by removing it.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This member is actually not needed as beacon abort
is only allowed for a bss station.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The MAC address parameters passed to iwl_parse_nvm_data() are passed on
to iwl_set_hw_address_family_8000() which treats them as little endian.
Annotate them as such, and add the missing byte-swapping in mvm.

While at it, add the MAC address to the error to make debugging issues
with it easier.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Previous patches enabled the multi-queue rx path based on
iwl_mvm_has_new_rx_api() which returned false by default.
Change it to return the actual value based on the firmware
TLV which is now defined.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The firmware will return the baid for BA session in the
ADD_STA command response.
This requires masking the check of the status, which is
actually only 8 bits, and not the whole 32 bits.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Print a debug message in iwl_mvm_config_scan() if a scan configuration
data is decided not to be sent to FW.
Signed-off-by: NMax Stepanov <Max.Stepanov@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Make the code clearer.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

For debug purposes, allow setting minimum quota (for a single
virtual interface) from debugfs. This is an absolute minimum,
so it can only be set up to 95%.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

To be able to test low-latency behaviour properly, split the
different low-latency sources so that setting any one of them,
for example from debugfs, is sufficient; this avoids getting
the debug setting overwritten by other sources.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Currently firmware is configured to filter out beacons. In case
a beacon was changed - it is waking the host.
However, some vendors change their IEs frequently without any
significant change, and redundant wakeups are triggered as a
result.
As a solution disable beacon filtering when entering d0i3.
Instead, firmware will store the latest beacon and upon exiting
d0i3 it will send it up to the host, so the host can act upon
changes (if there were any).
This beacon will arrive as a dedicated notification - support it
as well.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The driver should support also negative temperatures.
So there is a need to separate between the return value and
temperature in order to be able to distinguish between
a negative temperature and error value.
Signed-off-by: NChaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Using kstrtouint() with a signed int isn't really right,
use kstrotoint() instead.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

The outer scope has a perfectly suitable 'i' variable,
use it instead of adding a shadowing one in the inner
scope.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Slow platforms may have issues with dumping data upon
firmware assert. Make it easier to disable it for those
platform.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

Enable snoozing and U-APSD on P2P client. The firwmare will
support this only if the BSS vif is not associated.
Make this configurable by a constant variable and disable
it by default.
Signed-off-by: NAvri Altman <avri.altman@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This will allow to collect the data when the firmware
sends a specific tx response status.
Signed-off-by: NGolan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

This patch documents two missing module options in the internal
code comment block.
Signed-off-by: NRodrigo Freire <rfreire@redhat.com>
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

In order to have the LED being OFF constantly when the
brightness is set to 0, we need to pass IWL_LED_SOLID to
iwl_led_cmd as the off parameter, otherwise the led will
stay on constantly.

This fixes
https://bugzilla.kernel.org/show_bug.cgi?id=110551Signed-off-by: NHubert Tarasiuk <hubert.tarasiuk@gmail.com>
[reworked the commit message]
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>

No need to include net/ip6_checksum.h twice.
Remove TODOs.
Remove trailing space.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>