At least on pandora, STS_VBUS gets set even when VBUS is driven by twl
itself. Reporting VBUS in this case confuses OMAP musb glue and charger
driver, so check if OTG VBUS charge pump is on before reporting VBUS
event to avoid this problem.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fix the following sparse warning:

drivers/usb/musb/ux500_dma.c:60:6: warning: symbol 'ux500_dma_callback' was not declared. Should it be static?
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fix the following sparse warnings:

drivers/usb/gadget/mv_u3d_core.c:223:20: warning: context imbalance in 'mv_u3d_done' - unexpected unlock
drivers/usb/gadget/mv_u3d_core.c:1562:25: warning: context imbalance in 'mv_u3d_handle_setup_packet' - unexpected unlock

Note that the non-trivial sparse warnings
are left out of this commit due to lack of
HW to test:

drivers/usb/gadget/mv_u3d_core.c:906:42: warning: incorrect type in argument 2 (different address spaces)
drivers/usb/gadget/mv_u3d_core.c:906:42:    expected void [noderef] <asn:2>*<noident>
drivers/usb/gadget/mv_u3d_core.c:906:42:    got unsigned int *<noident>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fix the following sparse warnings:

drivers/usb/gadget/mv_udc_core.c:1850:6: warning: symbol 'irq_process_reset' was not declared. Should it be static?
drivers/usb/gadget/mv_udc_core.c:247:9: warning: context imbalance in 'done' - unexpected unlock
drivers/usb/gadget/mv_udc_core.c:1692:25: warning: context imbalance in 'handle_setup_packet' - unexpected unlock

Note that there are still other sparse warnings
which aren't trivial to fix, so I left them out:

drivers/usb/gadget/mv_udc_core.c:848:34: warning: incorrect type in argument 1 (different address spaces)
drivers/usb/gadget/mv_udc_core.c:848:34:    expected void const volatile [noderef] <asn:2>*addr
drivers/usb/gadget/mv_udc_core.c:848:34:    got unsigned int *<noident>
drivers/usb/gadget/mv_udc_core.c:849:42: warning: incorrect type in argument 2 (different address spaces)
drivers/usb/gadget/mv_udc_core.c:849:42:    expected void volatile [noderef] <asn:2>*addr
drivers/usb/gadget/mv_udc_core.c:849:42:    got unsigned int *<noident>
Acked-by: NNeil Zhang <zhangwm@marvell.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fix the following sparse warnings:

drivers/usb/gadget/pch_udc.c:1483:9: warning: context imbalance in 'complete_req' - unexpected unlock
drivers/usb/gadget/pch_udc.c:2408:28: warning: context imbalance in 'pch_udc_svc_control_out' - unexpected unlock
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fix the following sparse warning:

drivers/usb/gadget/dummy_hcd.c:1912:12: warning: symbol 'usb3_bos_desc' was not declared. Should it be static?
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

fix the following sparse warnings:

drivers/usb/gadget/net2280.c:2063:13: warning: Using plain integer as NULL pointer
drivers/usb/gadget/net2280.c:2321:68: warning: Using plain integer as NULL pointer
drivers/usb/gadget/net2280.c:2349:68: warning: Using plain integer as NULL pointer
drivers/usb/gadget/net2280.c:2371:68: warning: Using plain integer as NULL pointer
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix the following sparse warnings:

drivers/usb/gadget/net2272.c:916:13: warning: Using plain integer as NULL pointer
drivers/usb/gadget/net2272.c:1624:9: warning: Using plain integer as NULL pointer
drivers/usb/gadget/net2272.c:1552:30: warning: right shift by bigger than source value

Note that the last warning is an actual bug,
since ep->dma is a one bit value which is
shifted by one bit in code.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

this driver compiles fine everywhere which
means we can use linux-next to compile it
for us frequently.

By dropping the arch dependency, we also
ensure driver writers don't add virtual
arch-depdencies to the driver by e.g. using
the wrong headers.

While at that, fix Marvell's USB3 PHY dependency,
that's the driver which depends on CPU_MM3, not
mv_u3d_core.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix the following sparse warnings:

drivers/usb/gadget/mv_u3d_core.c: In function ‘mv_u3d_ep_queue’:
drivers/usb/gadget/mv_u3d_core.c:812:2: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/mv_u3d_core.c:822:14: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/mv_u3d_core.c:823:4: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/mv_u3d_core.c:823:28: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/mv_u3d_core.c: In function ‘mv_u3d_ep_dequeue’:
drivers/usb/gadget/mv_u3d_core.c:905:14: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/mv_u3d_core.c: In function ‘mv_u3d_probe’:
drivers/usb/gadget/mv_u3d_core.c:1840:3: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/mv_u3d_core.c:1855:51: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/mv_u3d_core.c:1855:17: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/usb/gadget/mv_u3d_core.c:1858:53: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
drivers/usb/gadget/mv_u3d_core.c:1858:18: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
drivers/usb/gadget/mv_u3d_core.c: In function ‘mv_u3d_irq_process_tr_complete’:
drivers/usb/gadget/mv_u3d_core.c:163:21: warning: ‘remaining_length’ may be used uninitialized in this function [-Wmaybe-uninitialized]
drivers/usb/gadget/mv_u3d_core.c:125:28: note: ‘remaining_length’ was declared here
Signed-off-by: NFelipe Balbi <balbi@ti.com>

USB_GADGET_{DUAL,SUPER}SPEED symbols have
been removed by commit 85b8614d (usb: gadget:
get rid of USB_GADGET_{DUAL,SUPER}SPEED), for
some reason mv_u3d_core was lost.

Remove those selects now.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

none of those headers are used by the driver,
removing them still compiles fine.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Make mv_u3d_pm_ops static because mv_u3d_pm_ops is not exported.
Also, CONFIG_PM_SLEEP is used to remove unnecessary ifdefs.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

VBUS_ERROR is a serious error that the driver often doesn't recover from
in my tests, so we should at least inform the user about it.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some musb glue drivers use gadget_driver pointer to know if any gadget
drivers are loaded at some moment and base further decisions on it,
like to do runtime suspend/resume or not. Right now the pointer is
left alone on stop and OMAP musb glue later does wrong runtime_pm
decisions because of it.

Clear the gadget_driver pointer on remove, it's invalid after stop
anyway.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As the usb transceiver driver usually starts first, it should already
have default_a variable set according to ID pin state, so don't
override it. In case default_a was not changed by trasceiver, it will
default to 0 and this code will work as before.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

PHY layer no longer returns NULL, we must
switch from IS_ERR_OR_NULL() to IS_ERR().
Acked-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

On pandora, STS_USB interrupt doesn't arrive on USB host cable disconnect
for some reason while VBUS is driven by twl itself, but STS_HW_CONDITIONS
is updated correctly. It does work fine when PHY is powered down though.
To work around that we have to poll.

This patch also moves twl->linkstat update code to callers so that
changes can be handled in thread safe way (as polling work can trigger
at the same time as real irq now).

TI PSP kernels have similar workarounds, so (many?) more boards are likely
affected.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

With runtime_pm in place there is no longer need to turn the phy
on/off in OTG layer on cable connect/disconnect, OMAP glue does
this through otg.set_suspend() callback after it's called through
omap_musb_mailbox() on VBUS/ID interrupt. Not doing this will save
power when cable is connected but no gadget driver is loaded.

This will also have side effect of automatic USB charging no longer
working without twl4030_charger driver, because a regulator needed
for charging will no longer be enabled, so be sure to enable charger
driver if charging is needed.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In some rare cases we may get multiple interrupts that will generate
duplicate omap_musb_mailbox() calls. This is a problem because each
VBUS/ID event generates runtime_pm call in OMAP glue code, causing
unbalanced gets or puts and breaking PM.

The same goes for initial state, glue already defaults to "no cable"
state, so only bother it if we have VBUS or ID.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Reviewed-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

There is no need to do it, otg.set_suspend(false) (which itself
comes from runtime_pm OMAP glue calls) will enable it later anyway.
This used to be the place where things were enabled if booted with
cable connected before runtime_pm conversion, but now can be dropped.
Signed-off-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

USB_ULPI and USB_ULPI_VIEWPORT shouldn't really
be selected directly by anyone, but since Tegra
still needs some time before turning ulpi viewport
into a proper PHY driver, we need to keep the
selects in place.

This patch just fixes the conditional select
so that it will continue to build after merging
the latest PHY layer changes.
Acked-by: NStephen Warren <swarren@nvidia.com>
Tested-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Due to recent changes to regulator API, all
users which don't check regulator_{en,dis}able()'s
return value will generate compile warnings.

Add such checks to gpio-vbus.

Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix the following sparse warning:

drivers/usb/phy/phy-samsung-usb2.c:50:26: sparse: incorrect type in argument 1 (different address spaces)
drivers/usb/phy/phy-samsung-usb2.c:50:26:    expected void const volatile [noderef] <asn:2>*addr
drivers/usb/phy/phy-samsung-usb2.c:50:26:    got void *

Cc: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Update irq handling code to notify all possible link status changes of
AB8500 and AB8505 to the ux500-musb glue driver.  The additional event
codes will be used for pm-runtime implementation, and are defined in a
separate ux500-specific header.

This also modify the irq registration code to use devm_* helpers and
drop all non necessary fail path code.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

AB8500 versions preceding 2.0 were only used internally by ST-Ericsson
and are not supported anymore.  This patch drops all v1.0 and v1.1
support code.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add transceiver notifier event handling to the ux500 driver to set vbus
on specific transceiver events.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>

[ balbi@ti.com: fix build error due to missing
	otg_state_string() ]
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add ux500_musb_set_vbus() implementation for ux500.

This is based on the version originally developed inside ST-Ericsson.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>

[ balbi@ti.com: fix a build error due to
	missing otg_state_string() ]
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix dma_controller_create() fail path in case memory resource is
missing.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NVirupax Sadashivpetimath <virupax.sadashivpetimath@stericsson.com>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

PHY layer no longer returns NULL. We must
switch from IS_ERR_OR_NULL() to IS_ERR().
Signed-off-by: NFelipe Balbi <balbi@ti.com>

PHY layer no longer returns NULL. We must
switch from IS_ERR_OR_NULL() to IS_ERR().
Signed-off-by: NFelipe Balbi <balbi@ti.com>

PHY layer no longer returns NULL. We must
switch from IS_ERR_OR_NULL() to IS_ERR().
Signed-off-by: NFelipe Balbi <balbi@ti.com>

PHY layer no longer returns NULL. We must
switch from IS_ERR_OR_NULL() to IS_ERR().
Signed-off-by: NFelipe Balbi <balbi@ti.com>

PHY layer no longer returns NULL. It will
return -ENXIO when PHY layer isn't enabled
and we can use that to bail out instead of
request a probe deferral.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

PHY laye rno longer return NULL. We need to
switch over from IS_ERR_OR_NULL() to IS_ERR().
Signed-off-by: NFelipe Balbi <balbi@ti.com>

PHY layer no longer returns NULL. It will
return -ENXIO when PHY layer isn't enabled
and we can use that to bail out instead of
request a probe deferral.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

PHY layer no longer returns NULL. It will
return -ENXIO when PHY layer isn't enabled
and we can use that to bail out instead of
request a probe deferral.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Having twl4030_usb_phy_init() (detects if a cable is connected before
twl4030 is probed) in twl4030 probe makes cable connect events to be
missed by musb glue, since it gets loaded after twl4030. Having
twl4030_usb_phy_init as a usb_phy ops lets twl4030_usb_phy_init to be
called when glue is ready.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Used devres APIs devm_request_threaded_irq and devm_regulator_get for
requesting irq and for getting regulator respectively.
Signed-off-by: NKishon Vijay Abraham I <kishon@ti.com>
Tested-by: NGrazvydas Ignotas <notasas@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

in cases where PHY layer isn't enabled, we want
to still return an error code (actually an error
pointer) so that our users don't need to cope with
either error pointer of NULL.

This will simplify users as below:

-	return IS_ERR(phy) ? PTR_ERR(phy) : -ENODEV;
+	return PTR_ERR(phy);
Acked-by: NKishon Vijay Abraham I <kishon@ti.com>
Reported-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NFelipe Balbi <balbi@ti.com>