Support for setting bandwidth and VHT parameters is still missing
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Define H2C command structure for setting the rate mask.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Further correct the handling of 40 byte TX descriptors.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Correct the setting of TX RTS for 8723a generation chips. In addition
update documentation to match that this is part of data word 4, note
data word 5.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TX data words 4 and 5 differ significantly between 32 byte and 40 byte
descriptors.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

SEQ changed location in the 40 byte TX descriptor. Set it correctly.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add additional bit definitions for 40 byte TX descriptors, and rename
bits for 32 byte descriptors that are located differently in the 40
byte descriptor format.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This adds documentation for some additional bits in TX descriptor word
0.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Note the descriptor checksum is still only calculated over the initial
32 bytes of the descriptor, ignoring the last 8 bytes of the
descriptor.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Newer generation chips use a 40 byte TX descriptor, compared to the
32 byte descriptor used on older chips.

This adds the definition for the 40 byte descriptor.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This should (hopefully) parse the power indices correctly for the
8723bu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Newer generation chips have more channels groups. In order to carry
the larger arrays in common structures, bump the array sizes to
match.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8723b series is significantly different from the older generation
in this sense. So far the 8723b version doesn't do anything useful.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Correct TX power definitions in rtl8723bu_efuse
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

These settings simply block the 8723bu, for now leave an empty
function.

With this change we can finally communicate with aliens using the
8723bu!
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Vendor driver implements this for 8723b and 8821 series
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This initializes RX DMA aggregation on 8723bu. We should do this for
all parts eventually, and also init TX aggregation.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Retrieve the XTAL_K value in the parse_efuse() functions as it's
location various on a per device basis. For parts that do not provide
an XTAL_K value, skip setting it.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Issue a BT_INFO command to verify the status of BT/WiFi settings.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

8723bu BT registers are written via the mailbox interface. Add support
for writing these and corresponding C2H event responses.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 64 bit mailbox commands also provide a different method for
mailbox command responses (C2H events).
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This adds code to parse the new RX descriptor format used by the
8723bu/8192eu parts.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The nextgen chips use a slightly different RX descriptor format. This
adds support for the new format.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8723bu is a WiFi/BT combo part. When initializing it for WiFi,
make sure to tell it not to ignore WiFi activity.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Implement additional init sequence code for the 8723bu.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This should initialize the antennas on the 8723bu, but so far I am
still not receiving anything :( More work is needed.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This is a first stab of implementing rtl8723bu_config_channel(). For
now this will only do 20MHz channels.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

TX power values are laid out differently in EFUSE found in RTL8192EU &
RTL8188EU devices.  TX power indices and differences for each RF path
are not interleaved (A, B, A, B), as in other chips, but follow one
another (A, B, C, D).
Signed-off-by: NJakub Sitnicki <jsitnicki@gmail.com>
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

This was inspired by the vendor driver, but in the end never used for
anything.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Newer chips (8723bu/8192eu) has S0S1 settings which needs to be dealt
with during LC calibration.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The 8723bu also has it's own IQK calibration process. This is similar
in flow, but still different enough to warrent it's own
implementation, at least for now.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

rtl8192cu/rtl8188cu/rtl8723au use the same values, but 8723bu and
8192eu have their own.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Newer generation chips require the firmware be notified before we
start the IQK calibration.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The firmware command API differs slightly between new and old
devices. The new generation requires the size since there is no
extension bit encoded into the command number.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

The larger mailboxes also use a different set of mailbox commands.
This provides a list of the 64 bit commands.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Gen1 chips use a 16 bit mailbox extension register, for upto 48 bit
mailbox commands. The newer generation chips use a 32 bit mailbox
extension register instead, for upto 64 bit mailbox commands.

Handle writing the larger mailboxes.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

So far this is just for 8723BU. It includes writing to a number of
registers I have seen no description for so far.

0x0064
0x0930
0x0944
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Add 8723bu 1T radio init table. The vendor driver indicates that some
registers need special treatment for TFBGA90, TFBGA80, and TFBGA79
packaging. However the vendor driver never actually checks the package
type, so just stick to default values here.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Only 1st generation chips do provide USB interrupts, so do not try to
setup interrupts for newer chips (8192eu and 8723bu).
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>

Implement first stab at parsing the 8723bu's efuse.
Signed-off-by: NJes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NKalle Valo <kvalo@codeaurora.org>