Right after runtime resume we know that we can re-enable DC5, since we
just disabled DC9 and power well 2 is disabled. So enable DC5 explicitly
instead of delaying this until the next time we disable power well 2.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NBob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-5-git-send-email-imre.deak@intel.com

After suspend-to-ram or -disk we don't know what power state the display
HW will be, DC0 or DC9 are both possible states, so reset the software
DC state tracking in these cases. This gets rid of 'DC state mismatch'
error messages during resuming from ram or disk where we expected to be
in DC9 (as set by the suspend handler) but we are in DC0.

v2:
- Remove extra WS in gen9_sanitize_dc_state() (Bob)
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NBob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-4-git-send-email-imre.deak@intel.com

Atm, we run the BSpec display core uninit/init sequences twice during
system suspend/resume. While this shouldn't cause any problem, it's
redundant, so get rid of the duplicate call.
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NBob Paauwe <bob.j.paauwe@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-3-git-send-email-imre.deak@intel.com

Initially we thought that the platform specific suspend/resume sequences
can be shared between the runtime and system suspend/resume handlers.
This turned out to be not true, we have quite a few differences on most
of the platforms. This was realized already earlier by Paulo who
inlined the platform specific resume_prepare handlers. We have the
same problem with the corresponding suspend_complete handlers, there are
platform differences that make it unfeasible to share the code between
the runtime and system suspend paths. Also now we call functions that
need to be paired like hsw_enable_pc8()/hsw_disable_pc8() from different
levels of the call stack, which is confusing. Fix this by inlining the
suspend_complete handlers too.

This is also needed by the next patch that removes a redundant
uninit/init call during system suspend/resume on BXT.

No functional change.

CC: Paulo Zanoni <przanoni@gmail.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NBob Paauwe <bob.j.paauwe@intel.com>
[s/uninline/inline in the commit message]
Link: http://patchwork.freedesktop.org/patch/msgid/1461173277-16090-2-git-send-email-imre.deak@intel.com

In commit 5f304c87 ("drm/i915/kbl: Reset secondary power well requests
left on by DMC/KVMR") I forgot about the fact that SKL==KBL most of the
time and that a secondary MISC IO power well request left on by the DMC is
"expected". Tune down the corresponding WARN to be a debug message. This
was caught by CI suspend tests.

CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461060036-19043-1-git-send-email-imre.deak@intel.com

It was noticed on bug #94087 that module parameter
i915.edp_vswing=2 that should override the VBT setting
to use default voltage swing (400 mV) was not applied
for Broadwell.

This patch provides a fix for this by checking if default
i.e. higher voltage swing is requested to be used and
applies the DDI translations table for DP instead of eDP
(low vswing) table.

v2: Combine two if statements into one (Jani)
v3: Change dev_priv->edp_low_vswing to use dev_priv->vbt.edp.low_vswing

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94087Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461155942-7749-1-git-send-email-mika.kahola@intel.com
Cc: stable@vger.kernel.org
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

The newly-introduced function i915_gem_object_pin_map() returns an
ERR_PTR (not NULL) if the pin-and-map opertaion fails, so that's what we
must check for. And it's nicer not to assign such a pointer-or-error to
a structure being filled in until after it's been validated, so we
should keep it local and avoid exporting a bogus pointer. Also, for
clarity and symmetry, we should clear 'virtual_start' along with 'vma'
when unmapping a ringbuffer.
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

Tidying up guc_init_proc_desc() and adding commentary to the client
structure after the recent change in GuC page mapping strategy.
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461078516-28678-1-git-send-email-david.s.gordon@intel.comReviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

Now that we keep the GuC client process descriptor permanently mapped,
we don't really need to keep a local copy of the GuC's work-queue-head.
So we can simplify the code a little by not doing this.
Signed-off-by: NAlex Dai <yu.dai@intel.com>
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

Don't use kmap_atomic() for doorbell & process descriptor access.
This patch fixes the BUG shown below, where the thread could sleep
while holding a kmap_atomic mapping. In order not to need to call
kmap_atomic() in this code path, we now set up a permanent kernel
mapping of the shared doorbell and process-descriptor page, and
use that in all doorbell and process-descriptor related code.

  BUG: scheduling while atomic: gem_close_race/1941/0x00000002
  Modules linked in: hid_generic usbhid i915 asix usbnet libphy mii
    i2c_algo_bit drm_kms_helper cfbfillrect syscopyarea cfbimgblt
    sysfillrect sysimgblt fb_sys_fops cfbcopyarea drm coretemp i2c_hid
    hid video pinctrl_sunrisepoint pinctrl_intel acpi_pad nls_iso8859_1
    e1000e ptp psmouse pps_core ahci libahci
  CPU: 0 PID: 1941 Comm: gem_close_race Tainted: G     U 4.4.0-160121+ #123
  Hardware name: Intel Corporation Skylake Client platform/Skylake AIO
    DDR3L RVP10, BIOS SKLSE2R1.R00.X100.B01.1509220551 09/22/2015
    0000000000013e40 ffff880166c27a78 ffffffff81280d02 ffff880172c13e40
    ffff880166c27a88 ffffffff810c203a ffff880166c27ac8 ffffffff814ec808
    ffff88016b7c6000 ffff880166c28000 00000000000f4240 0000000000000001
  Call Trace:
    [<ffffffff81280d02>] dump_stack+0x4b/0x79
    [<ffffffff810c203a>] __schedule_bug+0x41/0x4f
    [<ffffffff814ec808>] __schedule+0x5a8/0x690
    [<ffffffff814ec927>] schedule+0x37/0x80
    [<ffffffff814ef3fd>] schedule_hrtimeout_range_clock+0xad/0x130
    [<ffffffff81090be0>] ? hrtimer_init+0x10/0x10
    [<ffffffff814ef3f1>] ?  schedule_hrtimeout_range_clock+0xa1/0x130
    [<ffffffff814ef48e>] schedule_hrtimeout_range+0xe/0x10
    [<ffffffff814eef9b>] usleep_range+0x3b/0x40
    [<ffffffffa01ec109>] i915_guc_wq_check_space+0x119/0x210 [i915]
    [<ffffffffa01da47c>] intel_logical_ring_alloc_request_extras+0x5c/0x70 [i915]
    [<ffffffffa01cdbf1>] i915_gem_request_alloc+0x91/0x170 [i915]
    [<ffffffffa01c1c07>] i915_gem_do_execbuffer.isra.25+0xbc7/0x12a0 [i915]
    [<ffffffffa01cb785>] ?  i915_gem_object_get_pages_gtt+0x225/0x3c0 [i915]
    [<ffffffffa01d1fb6>] ? i915_gem_pwrite_ioctl+0xd6/0x9f0 [i915]
    [<ffffffffa01c2e68>] i915_gem_execbuffer2+0xa8/0x250 [i915]
    [<ffffffffa00f65d8>] drm_ioctl+0x258/0x4f0 [drm]
    [<ffffffffa01c2dc0>] ? i915_gem_execbuffer+0x340/0x340 [i915]
    [<ffffffff8111590d>] do_vfs_ioctl+0x2cd/0x4a0
    [<ffffffff8111eac2>] ? __fget+0x72/0xb0
    [<ffffffff81115b1c>] SyS_ioctl+0x3c/0x70
    [<ffffffff814effd7>] entry_SYSCALL_64_fastpath+0x12/0x6a
  ------------[ cut here ]------------

v4:
  Only tear down doorbell & kunmap() client object if we actually
  succeeded in allocating a client object (Tvrtko Ursulin)

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93847Original-version-by: NAlex Dai <yu.dai@intel.com>
Signed-off-by: NDave Gordon <david.s.gordon@intel.com>
Cc: Tvtrko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>

Since we can only swap out shmemfs objects, those are the only ones that
can influence the ability of the shrinker to free pages. Currently, all
non-shmemfs objects have a raised pages_pin_count to protect them from
the shrinker, so this just makes the logic for can_release_pages()
clearer (and safer in future so that we don't over estimate our ability
to free up pages from future non-swappable objects).
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461150592-27818-3-git-send-email-chris@chris-wilson.co.ukReviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>

Inside the shrinker we call can_release_pages() to indicate whether or
not we can make forward progress in freeing up memory by unbinding that
object. When adding our report to oom, we should be using the same
logic.

Whilst here, change the reporting from bytes to pages so that it looks
smaller to the user!, is consistent with the neighbouring oom report
itself which displays counts in pages, and makes the unsigned long
overflow less likely.

v2: Split oversized format string into two lines
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461150592-27818-2-git-send-email-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

When iterating over the bound list, we expect all objects there to have
their pages pinned (by the bound VMA). So only report those objects with
additional pin count on their pages as "pinned". These should be those
objects used for display and hardware access.
Reported-by: NAkash Goel <akash.goel@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Akash Goel <akash.goel@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461150592-27818-1-git-send-email-chris@chris-wilson.co.uk

Just two WARN_ONs followed by pointer dereference I spotted by accident.

v2: Remove some more of the same.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1461080770-14693-1-git-send-email-tvrtko.ursulin@linux.intel.com

Looks like DPF was not implemented for gen8+ but the IER and IMR
are still enabled on initialization.

Since there is no code to handle this interrupt, gate the irq
enablement behind HAS_L3_DPF in case the feature gets enabled
in the future.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>

WaEnableSamplerGPGPUPreemptionSupport fixes a problem
related to mid thread pre-emption.
Signed-off-by: NTim Gore <tim.gore@intel.com>
Reviewed-by: NDave Gordon <david.s.gordon@intel.com>
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461077152-31899-1-git-send-email-tim.gore@intel.com

Since commit 30d9aa42 ("drm/i915: Read sink_count dpcd always"),
the status of a DP connector depends on its sink count value.
However, some eDP panels don't set that value appropriately,
causing them to be reported as disconnected.
Fix this by ignoring sink count for eDP.

v2: Rephrased commit message. (Ander)
    In case of eDP, returning status as connected if DPCD
    read succeeds to avoid any further operations.

Fixes: 30d9aa42 ("drm/i915: Read sink_count dpcd always")
Cc: Ander Conselvan De Oliveira <conselvan2@gmail.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reported-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Signed-off-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NShubhangi Shrivastava <shubhangi.shrivastava@intel.com>
Tested-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460444034-22320-1-git-send-email-shubhangi.shrivastava@intel.com

In commit 7d23e3c3 ("drm/i915: Cleaning up intel_dp_hpd_pulse") some
much needed clean-up was done, but unfortunately part of the change
broke DP MST.  The real issue was setting the connector state to
disconnected in the MST case, which is good, but the code then (after
a goto) checks if the connector state is not connected and shuts down
MST if this is the case, which is bad.  With this change both SST and
MST seem to be happy.

v2: Add removed check further up in the function to be sure that MST
    is shut down when we lose the link. (Ander)

Fixes: commit 7d23e3c3 ("drm/i915: Cleaning up intel_dp_hpd_pulse")
cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
cc: Shubhangi Shrivastava <shubhangi.shrivastava@intel.com>
cc: Ander Conselvan de Oliveira <conselvan2@gmail.com>
cc: Nathan D Ciobanu <nathan.d.ciobanu@intel.com>
Signed-off-by: NJim Bride <jim.bride@linux.intel.com>
Reviewed-by: NAnder Conselvan de Oliveira <conselvan2@gmail.com>
Reviewed-by: NLyude <cpaul@redhat.com>
Signed-off-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460394684-7036-1-git-send-email-jim.bride@linux.intel.com

Do not use magic numbers, do not prefix stuff with "PCI_", do not
declare registers in implementation files. Also move the PCI
registers under correct comment in i915_reg.h.

v2:
- Consistently use BSM (not BDSM or other variants from PRM) (Chris)
- Also include register address to help identify the register (Chris)
v3:
- Refer to register value as *_val instead of *_reg (Chris)
v4:
- Make style checker happy

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>

We need to kunmap pt_vaddr and not pt itself, otherwise we end up
mapping a bunch of pages without ever unmapping them.

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Fixes: d1c54acd ("drm/i915/gtt: Introduce kmap|kunmap for dma page")
Signed-off-by: NMatthew Auld <matthew.auld@intel.com>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460476663-24890-4-git-send-email-matthew.auld@intel.com

The power cycle delay starts _after_ turning off the panel power. Do the
msleep after frobbing the pmic panel power gpio.

Also toss in a FIXME about optimizing away needless waits.

Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Fixes: fc45e821 ("drm/i915: Use the CRC gpio for panel enable/disable")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460996271-29795-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NShobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>

Currently we're trying to define HSW/BDW power wells by what's not
included. Let's do it the other way around, so that you can actually
tell when the power well would get enabled. This will also allow us to
add new power domains without accidentally adding it to the HSW/BDW
display power domains.

The current set of domains looks rather buggy even:
- POWER_DOMAIN_MODESET is included in the display power well needlessly
- DDI-B to DDI-E were not part of the display power well when they
  should be

So let's fix that up while at it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

Currently we're using POWER_DOMAIN_MASK as the power domains for the
display power well on VLV/CHV. That includes all power domains even
though the disp2d/pipe-a power well is not needed for a lot of things.
Let's reduce these to what we actually need.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

The always-on well is the same as runtime PM, so we should just
"enable" it for any power domain. Throw out the usless
FOO_ALWAYS_ON_DOMAINS defines and just use POWER_DOMAIN_MASK.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460977348-32260-2-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

intel_pipe_will_have_type() doesn't just look at the passied in
pipe_config, instead it expects there to be a full atomic state behind
it. Obviously that won't go so well when vlv_force_pll_on() just uses a
temp pipe_config. Fix things by using pipe_config->has_dsi_encoder
instead intel_pipe_will_have_type(INTEL_OUTPUT_DSI) to check if we need
to actually enable the DPLL.

Here's an example oops for reference:
BUG: unable to handle kernel NULL pointer dereference at 0000000000000030
IP: [<ffffffffa0389a5b>] intel_pipe_will_have_type+0x15/0x7b [i915]
PGD 7acda067 PUD 72696067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
Modules linked in: i915 i2c_algo_bit drm_kms_helper syscopyarea sysfillrect sysimgblt fb_sys_fops drm intel_gtt agpgart netconsole psmouse atkbd iTCO_wdt libps2 coretemp hwmon efi_pstore intel_rapl punit_atom_debug efivars pcspkr i2c_i801 r8169 lpc_ich mii processor_thermal_device snd_soc_rt5670 intel_soc_dts_iosf snd_soc_rl6231 i2c_hid hid snd_intel_sst_acpi snd_intel_sst_core snd_soc_sst_mfld_platform snd_soc_sst_match snd_soc_core i8042 serio snd_compress snd_pcm snd_timer snd i2c_designware_platform sdhci_acpi i2c_designware_core soundcore sdhci pwm_lpss_platform mmc_core pwm_lpss spi_pxa2xx_platform evdev int3403_thermal int3400_thermal int340x_thermal_zone acpi_thermal_rel sch_fq_codel ip_tables x_tables ipv6 autofs4
CPU: 3 PID: 290 Comm: Xorg Tainted: G     U          4.6.0-rc4-bsw+ #2876
Hardware name: Intel Corporation CHERRYVIEW C0 PLATFORM/Braswell CRB, BIOS BRAS.X64.X088.R00.1510270350 10/27/2015
task: ffff88007a8dd200 ti: ffff880173ac4000 task.ti: ffff880173ac4000
RIP: 0010:[<ffffffffa0389a5b>]  [<ffffffffa0389a5b>] intel_pipe_will_have_type+0x15/0x7b [i915]
RSP: 0018:ffff880173ac7928  EFLAGS: 00010246
RAX: 0000000000000000 RBX: ffff880176594000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: 0000000000000009 RDI: ffff880176594000
RBP: ffff880173ac7930 R08: 0000000000019290 R09: 0000000000000000
R10: ffff880173ac7890 R11: 00000000000080cf R12: ffff88017fbd4000
R13: ffffffffa03e3c44 R14: ffff88007492c000 R15: ffff88007492c000
FS:  00007ff8936a6940(0000) GS:ffff88017ef80000(0000) knlGS:0000000000000000
CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000030 CR3: 0000000177e08000 CR4: 00000000001006e0
Stack:
 ffff880176594000 ffff880173ac7948 ffffffffa0389b42 ffff880176594000
 ffff880173ac7978 ffffffffa0396e02 ffff8801765b0000 ffff88007af660d8
 0000000000000000 0000000000000004 ffff880173ac79c0 ffffffffa03b6b64
Call Trace:
 [<ffffffffa0389b42>] chv_compute_dpll.isra.39+0x33/0x55 [i915]
 [<ffffffffa0396e02>] vlv_force_pll_on+0x80/0xc6 [i915]
 [<ffffffffa03b6b64>] vlv_power_sequencer_pipe+0x29b/0x3dd [i915]
 [<ffffffffa03b6cd4>] _pp_stat_reg+0x2e/0x38 [i915]
 [<ffffffffa03b6dc1>] wait_panel_status+0x4c/0x1ec [i915]
 [<ffffffffa03b6fcb>] wait_panel_power_cycle+0x6a/0xb4 [i915]
 [<ffffffffa03b70da>] edp_panel_vdd_on+0xc5/0x1d1 [i915]
 [<ffffffffa03b861b>] intel_dp_aux_ch+0x55/0x572 [i915]
 [<ffffffff810af5c8>] ? mark_held_locks+0x5d/0x74
 [<ffffffff81518e61>] ? mutex_lock_nested+0x321/0x346
 [<ffffffff81094007>] ? preempt_count_sub+0xf2/0x102
 [<ffffffffa03b8cb4>] intel_dp_aux_transfer+0x17c/0x1b5 [i915]
 [<ffffffffa03028ef>] drm_dp_dpcd_access+0x62/0xed [drm_kms_helper]
 [<ffffffffa0302995>] drm_dp_dpcd_read+0x1b/0x1f [drm_kms_helper]
 [<ffffffffa03b5147>] intel_dp_dpcd_read_wake+0x31/0x69 [i915]
 [<ffffffffa03bb36a>] intel_dp_long_pulse+0x15f/0x5ed [i915]
 [<ffffffffa03bbb09>] intel_dp_detect+0x79/0x95 [i915]
 [<ffffffffa030340e>] drm_helper_probe_single_connector_modes+0xc7/0x3db [drm_kms_helper]
 [<ffffffffa029de23>] drm_mode_getconnector+0xe9/0x333 [drm]
 [<ffffffff810b1cfb>] ? lock_acquire+0x137/0x1df
 [<ffffffffa0292364>] drm_ioctl+0x266/0x3ae [drm]
 [<ffffffffa029dd3a>] ? drm_mode_getcrtc+0x126/0x126 [drm]
 [<ffffffff811af082>] vfs_ioctl+0x18/0x34
 [<ffffffff811af682>] do_vfs_ioctl+0x547/0x5fe
 [<ffffffff811b9acb>] ? __fget_light+0x62/0x71
 [<ffffffff811af77c>] SyS_ioctl+0x43/0x61
 [<ffffffff81001a82>] do_syscall_64+0x63/0xf8
 [<ffffffff8151bc9a>] entry_SYSCALL64_slow_path+0x25/0x25
Code: 35 00 40 a0 e8 97 4b ce e0 b8 17 00 00 00 5d c3 b8 17 00 00 00 c3 0f 1f 44 00 00 55 31 c0 31 d2 48 89 e5 53 48 8b 8f e8 01 00 00 <44> 8b 49 30 41 39 c1 7e 2d 4c 8b 51 38 4c 8b 41 40 49 83 3c c2
RIP  [<ffffffffa0389a5b>] intel_pipe_will_have_type+0x15/0x7b [i915]
 RSP <ffff880173ac7928>
CR2: 0000000000000030

The regressing patch wasn't exactly new (as in first posted more than
six months ago), so I'm a bit baffled how I didn't manage to hit this
myself so far.

Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Marius Vlad <marius.c.vlad@intel.com>
Reported-by: NMarius Vlad <marius.c.vlad@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94995
Fixes: cd2d34d9 ("drm/i915: Setup DPLL/DPLLMD for DSI too on VLV/CHV")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1461000844-20543-1-git-send-email-ville.syrjala@linux.intel.comTested-by: NMarius Vlad <marius.c.vlad@intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>

While we disable runtime PM and with that display power well support if
the DMC firmware isn't loaded, we still want to disable power wells
during system suspend and driver unload. So drop/reacquire the
corresponding power refcount during suspend/resume and driver unloading.
This also means we have to check if DMC is not loaded and skip enabling
DC states in the power well code.

v2:
- Reuse intel_csr_ucode_suspend() in intel_csr_ucode_fini() instead of
  opencoding the former. (Chris)
- Add docbook comment to the public resume and suspend functions.

CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460980101-14713-1-git-send-email-imre.deak@intel.com

The driver's VDD on/off logic assumes that whenever the VDD is on we
also hold an AUX power domain reference. Since BIOS can leave the VDD on
during booting and resuming and on DDI platforms we won't take a
corresponding power reference, the above assumption won't hold on those
platforms and an eventual delayed VDD off work will do an extraneous AUX
power domain put resulting in a refcount underflow. Fix this the same
way we did this for non-DDI DP encoders:

commit 6d93c0c4 ("drm/i915: fix VDD state tracking after system
resume")

At the same time call the DP encoder suspend handler the same way as the
non-DDI DP encoders do to flush any pending VDD off work. Leaving the
work running may cause a HW access where we don't expect this (at a point
where power domains are suspended already).

While at it remove an unnecessary function call indirection.

This fixed for me AUX refcount underflow problems on BXT during
suspend/resume.

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: stable@vger.kernel.org
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-4-git-send-email-imre.deak@intel.com

During system resume we depended on pci_enable_device() also putting the
device into PCI D0 state. This won't work if the PCI device was already
enabled but still in D3 state. This is because pci_enable_device() is
refcounted and will not change the HW state if called with a non-zero
refcount. Leaving the device in D3 will make all subsequent device
accesses fail.

This didn't cause a problem most of the time, since we resumed with an
enable refcount of 0. But it fails at least after module reload because
after that we also happen to leak a PCI device enable reference: During
probing we call drm_get_pci_dev() which will enable the PCI device, but
during device removal drm_put_dev() won't disable it. This is a bug of
its own in DRM core, but without much harm as it only leaves the PCI
device enabled. Fixing it is also a bit more involved, due to DRM
mid-layering and because it affects non-i915 drivers too. The fix in
this patch is valid regardless of the problem in DRM core.

v2:
- Add a code comment about the relation of this fix to the freeze/thaw
  vs. the suspend/resume phases. (Ville)
- Add a code comment about the inconsistent ordering of set power state
  and device enable calls. (Chris)

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
CC: stable@vger.kernel.org
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460979954-14503-1-git-send-email-imre.deak@intel.com

If system resume fails, this may lead to a runtime PM wake reference
underflow used for runtime PM state checking.

Fixes: 1f814dac ("drm/i915: add support for checking if we hold an RPM reference")
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460963062-13211-2-git-send-email-imre.deak@intel.com

The workaround added in
commit c6782b76 ("drm/i915/gen9: Reset secondary power well
requests left on by DMC/KVMR")
needs to be applied on Kabylake too as shown by the corresponding
timeout errors about power well 1 and MISC IO power well disabling in
the latest CI run.

CC: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NPatrik Jakobsson <patrik.jakobsson@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460748778-4484-1-git-send-email-imre.deak@intel.com

When a vblank wait times out in intel_atomic_wait_for_vblanks() we just
get a cryptic 'WARN_ON(!ret)' backtrace in dmesg. Repace it with
something that tells you what actually happened.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460978973-24945-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

The legacy cursor ioctl expects to be asynchronous with respect to other
screen updates, in particular page flips. As X updates the cursor from a
signal context, if the cursor blocks then it will stall both the input
and output chains causing bad stuttering and horrible UX.
Reported-and-tested-by: NRafael Ristovski <rafael.ristovski@gmail.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94980
Fixes: 5008e874 ("drm/i915: Make wait_for_flips interruptible.")
Suggested-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: stable@vger.kernel.org
Link: http://patchwork.freedesktop.org/patch/msgid/1460922166-20292-1-git-send-email-chris@chris-wilson.co.ukAcked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>

Due to "some hardware limitation" the DPI enable bit in port C control
register does not get set on VLV. As a workaround we check the status in
pipe B conf register instead. The workaround was added in

commit c0beefd2
Author: Gaurav K Singh <gaurav.k.singh@intel.com>
Date:   Tue Dec 9 10:59:20 2014 +0530

    drm/i915: Software workaround for getting the HW status of DSI Port C on BYT

Empirical evidence (on Surface 3 with DSI on port C per VBT) shows that
this is the case also on CHV, so extend the workaround to CHV. We still
have the device ready register check in place, so this should not get
confused with e.g. HDMI on pipe B.

This fixes a number of state checker warnings on CHV DSI port C.

Cc: stable@vger.kernel.org
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460724451-13810-1-git-send-email-jani.nikula@intel.com

Show a total and purgeable number of pin mapped objects
and their total and purgeable size.

Example output (new stat prefixed with a star):

  # cat i915_gem_objects
  19920 objects, 289243136 bytes
  19920 [18466] objects, 288714752 [267911168] bytes in gtt
    0 [0] active objects, 0 [0] bytes
    19917 [18466] inactive objects, 288714752 [267911168] bytes
  0 unbound objects, 0 bytes
  0 purgeable objects, 0 bytes
  1 pinned mappable objects, 3145728 bytes
  0 fault mappable objects, 0 bytes
* 19914 [0] pin mapped objects, 285560832 [0] bytes [purgeable]
  4294967296 [268435456] gtt total
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460716493-27826-1-git-send-email-tvrtko.ursulin@linux.intel.com

Reflect the status of obj->mapping as added with the
i915_gem_object_pin_map API.

'M' was chosen to designate the pin mapped status.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>

We don't have a LVDS_BORDER_ENABLE type of bit for either eDP or DSI,
and just trying to frob the display timings to include borders results
in a corrupted picture. So reject the 'Center' scaling mode on GMCH
platforms for eDP and DSI.

TODO: Should really filter out the unsupported modes from the prop,
but that would be fairly invasive since the prop is now created and
stored by drm core. So leave it for a rainy day.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-6-git-send-email-ville.syrjala@linux.intel.comTested-by: NJani Nikula <jani.nikula@intel.com>

Add the scaling mode property to DSI connectors, handle changes in the
property value, and compute the panel fitter state during
.compute_config().

v2: Handle BXT as well
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-5-git-send-email-ville.syrjala@linux.intel.comTested-by: NJani Nikula <jani.nikula@intel.com>

Fold the DSI PLL configuration functions into the DSI PLL
enable functions since they are small and not called from anywhere else.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-4-git-send-email-ville.syrjala@linux.intel.comTested-by: NJani Nikula <jani.nikula@intel.com>

Compute the DSI PLL parameters during .compute_config() rather than
.pre_pll_enable() so that we can fail gracefully if we can't find
suitable parameters.

In order to do that we need to store the DSI PLL parameters in
pipe_config.

v2: Handle BXT too
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-3-git-send-email-ville.syrjala@linux.intel.comTested-by: NJani Nikula <jani.nikula@intel.com>

Set up DPLL and DPLL_MD even when driving DSI output on VLV/CHV. While
the DPLL isn't used to provide the clock we still need the refclock, and
it appears that the pixel repeat factor also has an effect on DSI
output. So set up eveyrhing in DPLL and DPLL_MD as we would do for
DP/HDMI/VGA, but don't actually enable the DPLL or configure the
dividers via DPIO.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460488478-18311-2-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NJani Nikula <jani.nikula@intel.com>
Tested-by: NJani Nikula <jani.nikula@intel.com>