The 6320 family of switch chips has a second bank for statistics, but
is missing three statistics in the port registers. Generalise and
extend the code:

* adding a field to the statistics table indicating the bank/register
  set where each statistics is.
* add a function indicating if an individual statistics
  is available on this device
* calculate at run time the sset_count.
* return strings based on the available statistics of the device
* return statistics based on the available statistics of the device
* Add support for reading from the second bank.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The device tree binding now allows a gpio to be specified which is
attached to the switch chips reset line. If it is defined, perform
a hardware reset on the switch during setup.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To align with the mv88e6xxx code, use the register defines to
access all the register addresses and bit fields.
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

To align with the mv88e6xxx code, add a similar header file
with all the register defines.
The file is based on the mv88e6xxx header for coherency.
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Acked-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the mv88e6060 datasheet, the first mac byte must
be at position 9 instead of 8 since the bit 8 is used to select
if the mac address must differ for each port for Pause frames.
Use the correct shift and set the same mac address for all port.
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the mv88e6060 datasheet, the MaxFrameSize bit position
is 10 instead of 11 which is reserved.
Use the bit correctly to setup max frame size to 1536.
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

According to the mv88e6060 datasheet, the InitReady bit position
is 11 and the polarity is inverted.
Use the bit correctly to detect the end of initialization.
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Acked-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As of mv88e6xxx remove the poll_link callback since the link
state change polling is now handled by the phylib.

Tested on a mv88e6060 B0 device with a TI DM816X SoC.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The DSA documentation specifies that each port must be capable of
forwarding frames to the CPU port. The last changes on bridging support
for the mv88e6xxx driver broke this requirement for non-bridged ports.

So as for the bridged ports, reserve a few VLANs (4000+) in the switch
to isolate ports that have not been bridged yet.

By default, a port will be isolated with the CPU and DSA ports. When the
port joins a bridge, it will leave its reserved port. When it is removed
from a bridge, it will join its reserved VLAN again.

Fixes: 5fe7f680 ("net: dsa: mv88e6xxx: fix hardware bridging")
Reported-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DSA ports must be members of a VLAN in order to ensure frame bridging
between chained switch chips.

Thus tag them in addition to the CPU port when adding a VLAN, and skip
them when deleting a VLAN and reporting VLAN members.

Also use the UNMODIFIED egress policy, so that frames egress on these
ports as they ingress, tagged or untagged.

Fixes: 0d3b33e6 ("net: dsa: mv88e6xxx: add VLAN Load support")
Reported-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Frames with DSA headers passing to/from the CPU were taking place in the
MAC learning on these ports, resulting in incorrect ATU entries. Disable
learning on these ports.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All the mv88e6xxx drivers use the exact same code in their probe
function to lookup the switch name given its ID. Thus introduce a
mv88e6xxx_switch_id structure and a mv88e6xxx_lookup_name function in
the common mv88e6xxx code.

In the meantime make __mv88e6xxx_reg_{read,write} static since we do not
need to expose these low-level r/w routines anymore.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It's easy to forget to lock the smi_mutex before calling the low-level
_mv88e6xxx_reg_{read,write}, so add a assert_smi_lock function in them.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Simplify DSA by pushing the switchdev objects for VLAN add and delete
operations down to its drivers. Currently only mv88e6xxx is affected.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While the current driver mostly supports BCM7445 which has a hardcoded
location for its MoCA port on port 7 and port 0 for its internal PHY,
this is not necessarily true for all other chips out there such as
BCM3390 for instance.

Walk the list of ports from Device Tree, get their port number ("reg"
property), and then parse the "phy-mode" property and initialize two
internal variables: moca_port and a bitmask of internal PHYs. Since we
use interrupts for the MoCA port, we introduce two helper functions to
enable/disable interrupts and do this at the appropriate bank (INTRL2_0
or INTRL2_1).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for the FDB add, delete, and dump operations. The add and
delete operations are implemented using directed ARL operations using
the specified MAC address and consist in a read operation, write and
readback operation.

The dump operation consists in using the ARL search and software
filtering entries which are not for the desired port.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Like mv88e6xxx and mdio-mux, to avoid lockdep give false positives
because of nested MDIO busses, switch to previously introduced
nested mdiobus_read/write variants.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the mv88e6xxx driver use the previously introduced nested
variants of mdiobus_read/write functions.
Signed-off-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is preferable to have a common debugfs interface for DSA or switchdev
instead of a driver specific one. Thus remove the mv88e6xxx debug code.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that port_fdb_dump is implemented and even simpler, get rid of
port_fdb_getnext.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the port_fdb_dump DSA operation.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to write the MAC address before every Get Next
operation, since ATU MAC registers are not cleared between calls.

Move the _mv88e6xxx_atu_mac_write call outside of _mv88e6xxx_atu_getnext
so future code could call ATU Get Next multiple times and save a few
register access.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to write the VLAN ID before every Get Next operation,
since the VTU VID register is not cleared between calls.

Move the VID write call in a _mv88e6xxx_vtu_vid_write function outside
of _mv88e6xxx_vtu_getnext so future code could call VTU Get Next
multiple times and save a few register accesses.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Playing with the VLAN map of every port to implement "hardware bridging"
in the 88E6352 driver was a hack until full 802.1Q was supported.

Indeed with 802.1Q port mode "Disabled" or "Fallback", this feature is
used to restrict which output ports an input port can egress frames to.

A Linux bridge is an untagged VLAN. With full 802.1Q support, we don't
need this hack anymore and can use the "Secure" strict 802.1Q port mode.

With this mode, the port-based VLAN map still needs to be configured,
but all the logic is VTU-centric. This means that the switch only cares
about rules described in its hardware VLAN table, which is exactly what
Linux bridge expects and what we want.

Note also that the hardware bridging was broken with the previous
flexible "Fallback" 802.1Q port mode. Here's an example:

Port0 and Port1 belong to the same bridge. If Port0 sends crafted tagged
frames with VID 200 to Port1, Port1 receives it. Even if Port1 is in
hardware VLAN 200, but not Port0, Port1 will still receive it, because
Fallback mode doesn't care about invalid VID or non-member source port.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since we configure a switch chip through a Linux bridge, and a bridge is
implemented as a VLAN, there is no need for per-port FID anymore.

This patch gets rid of this and simplifies the driver code since we can
now directly map all 4095 FIDs available to all VLANs.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With 88E6352 and similar switch chips, each port has a map to restrict
which output port this input port can egress frames to.

The current driver code implements hardware bridging using this feature,
and assigns to a bridge group the FID of its first member.

Now that 802.1Q is fully implemented in this driver, a Linux bridge
which is a simple untagged VLAN, already gets its own FID.

This patch gets rid of the per-bridge FID and explicits the usage of the
port based VLAN map feature.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For consistency with the FDB add operation, propagate the
switchdev_obj_port_fdb structure in the DSA drivers.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the prepare phase is pushed down to the DSA drivers, propagate
it to the port_fdb_add function.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Push the prepare phase for FDB operations down to the DSA drivers, with
a new port_fdb_prepare function. Currently only mv88e6xxx is affected.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The link status is polled by the generic phy layer, there's no need to
duplicate that polling with additional polling.  This additional polling
adds additional MDIO traffic, and races with the generic phy layer,
resulting in missing or duplicated link status messages.
Tested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit dea87024 ("dsa: mv88e6xxx: Allow speed/duplex of port to be
configured") leads to the following static checker warning:

        drivers/net/dsa/mv88e6xxx.c:585 mv88e6xxx_adjust_link()
        warn: unsigned 'ret' is never less than zero.

drivers/net/dsa/mv88e6xxx.c
   573  void mv88e6xxx_adjust_link(struct dsa_switch *ds, int port,
   574                             struct phy_device *phydev)
   575  {
   576          struct mv88e6xxx_priv_state *ps = ds_to_priv(ds);
   577          u32 ret, reg;
   578
   579          if (!phy_is_pseudo_fixed_link(phydev))
   580                  return;
   581
   582          mutex_lock(&ps->smi_mutex);
   583
   584          ret = _mv88e6xxx_reg_read(ds, REG_PORT(port), PORT_PCS_CTRL);
   585          if (ret < 0)

Make ret an int, which is the return type for _mv88e6xxx_reg_read()
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Frames destined to an unknown address must be forwarded to the CPU
port. Otherwise incoming ARP, dhcp leases, etc, do not work.
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 54d792f2 ("net: dsa: Centralise global and port setup
code into mv88e6xxx.") merged in the 4.2 merge window broke the link
speed forcing for the CPU port of Marvell DSA switches.  The original
code was:

        /* MAC Forcing register: don't force link, speed, duplex
         * or flow control state to any particular values on physical
         * ports, but force the CPU port and all DSA ports to 1000 Mb/s
         * full duplex.
         */
        if (dsa_is_cpu_port(ds, p) || ds->dsa_port_mask & (1 << p))
                REG_WRITE(addr, 0x01, 0x003e);
        else
                REG_WRITE(addr, 0x01, 0x0003);

but the new code does a read-modify-write:

                reg = _mv88e6xxx_reg_read(ds, REG_PORT(port), PORT_PCS_CTRL);
                if (dsa_is_cpu_port(ds, port) ||
                    ds->dsa_port_mask & (1 << port)) {
                        reg |= PORT_PCS_CTRL_FORCE_LINK |
                                PORT_PCS_CTRL_LINK_UP |
                                PORT_PCS_CTRL_DUPLEX_FULL |
                                PORT_PCS_CTRL_FORCE_DUPLEX;
                        if (mv88e6xxx_6065_family(ds))
                                reg |= PORT_PCS_CTRL_100;
                        else
                                reg |= PORT_PCS_CTRL_1000;

The link speed in the PCS control register is a two bit field.  Forcing
the link speed in this way doesn't ensure that the bit field is set to
the correct value - on the hardware I have here, the speed bitfield
remains set to 0x03, resulting in the speed not being forced to gigabit.

We must clear both bits before forcing the link speed.

Fixes: 54d792f2 ("net: dsa: Centralise global and port setup code into mv88e6xxx.")
Signed-off-by: NRussell King <rmk+kernel@arm.linux.org.uk>
Acked-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When we're moving a port from Learning or Forwarding state to Disabled
or Blocking or Listening state, remove all non-static MAC addresses
mapped to this port in the entire set of databases, not only one.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a new _mv88e6xxx_atu_move function to prepare the ATU data register
for the move operation. The ports vector will contain the source port
and destination port of the Move operation. If the destination port is
0xF, the MAC addresses mapped to the source port are removed for the
address database(s).

Then add a _mv88e6xxx_atu_remove wrapper to remove the MAC addresses
from a VLAN database that are mapped to a given port, when it leaves it.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When choosing an address database for a new VLAN, flush every entries,
not only the non-static ones.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Purge all MAC addresses from the entire set of address databases when
the driver initializes the device.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

These Marvell switches have 4 operations to flush or (re)move, all or
only non-static MAC addresses, from the entire set of databases or from
just a particular one.

The value of the EntryState bits will determine if the operation is
either a Flush (0x0) or a Move (0xF).

When moving entries from one port to another, entries will be removed if
the destination port is 0xF.

This patch renames these operations for consistency, add a new generic
_mv88e6xxx_atu_flush_move function, and change _mv88e6xxx_flush_fid to
use it.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Other ATU commands need to write the ATU data register. To ease the
introduction of such commands, extract the ATU data write access from
_mv88e6xxx_atu_load to its own function.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not every ATU commands apply to an FID, thus remove the FID writing from
mv88e6xxx_atu_cmd and write it explicitly where needed, in order to ease
introduction of such commands.
Signed-off-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>