When hclge_ae_stop is called during resetting, it will cancel the
service_task by calling cancel_work_sync, which may cause the
service_task to exit without clearing HCLGE_STATE_SERVICE_SCHED
bit. If this happens, the service_task will never run again.

This patch fixes this problem by clearing it after calling
cancel_work_sync in hclge_ae_stop.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing function reset or insmod hns3 dirver after rmmod,
the entries of mac vlan table are not cleared, which may cause
init mac address failed. This patch fixes it by clearing the
old mac address when doing function reset or rmmod hns3 driver.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add checking for new mac address. It doesn't need to config
the mac vlan table if it's already in use.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for IFF_ALLMULTI flag to HNS3 PF and VF
driver.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is only 128 entries for hardware's vf vlan table, when
the vf table is full, the firmware will disable the vf vlan
filter and return a resp_code of HCLGE_VF_VLAN_NO_ENTRY to
driver.

This patch checks the if resp_code from firmware is
HCLGE_VF_VLAN_NO_ENTRY, if yes, then print a warning and
return ok to the caller.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As the mvpp2 driver is growing, move this driver to a dedicated
directory and split it into several files.

Since this driver has a lot of register defines and structure
definitions, it can benefit from having all of this into a dedicated
header file, named mvpp2.h.

A good chunk of the mvpp2 code is dedicated to Header Parser handling, so
we introduce mvpp2_prs.h where all Header Parser definitions are located,
and mvpp2_prs.c containing the related code.

In the same way, mvpp2_cls.h and mvpp2_cls.c are created to contain
Classifier and RSS related code.

The former 'mvpp2.c' file is renamed 'mvpp2_main.c' so that we can keep
the driver binary named 'mvpp2'.

This commit is only about spliting the driver into multiple files and
doesn't introduce any new function, feature or fix besides removing
'static' keywords when needed.
Signed-off-by: NMaxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: NAntoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to return a negative error code from the failover create fail error
handling case instead of 0, as done elsewhere in this function.

Fixes: ba5e4426 ("virtio_net: Extend virtio to use VF datapath when available")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make it explicit that either device tree is used or platform data.  If
neither is available, abort the probe.
Reported-by: NDan Carpenter <dan.carpenter@oracle.com>
Fixes: 877b7cb0 ("net: dsa: mv88e6xxx: Add minimal platform_data support")
Signed-off-by: NAndrew Lunn <andrew@lunn.ch>
Reviewed-by: NVivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On platforms that don't always enable CONFIG_GPIOLIB, we run into
a build failure:

drivers/net/ethernet/ti/cpsw.c: In function 'cpsw_probe':
drivers/net/ethernet/ti/cpsw.c:3006:9: error: implicit declaration of function 'devm_gpiod_get_array_optional' [-Werror=implicit-function-declaration]
  mode = devm_gpiod_get_array_optional(&pdev->dev, "mode", GPIOD_OUT_LOW);
         ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/ti/cpsw.c:3006:59: error: 'GPIOD_OUT_LOW' undeclared (first use in this function); did you mean 'GPIOF_INIT_LOW'?
  mode = devm_gpiod_get_array_optional(&pdev->dev, "mode", GPIOD_OUT_LOW);

Since we cannot rely on this to be visible from gpio.h, we have to include
gpio/consumer.h directly.

Fixes: 2652113f ("net: ethernet: ti: Allow most drivers with COMPILE_TEST")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FPGA queue pair (QP) event fires whenever a QP on the FPGA
transitions to the error state.

At this stage, this event is unrecoverable, it may become recoverable
in the future.
Signed-off-by: NIlan Tayari <ilant@mellanox.com>
Signed-off-by: NAdi Nissim <adin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Temperature warning event is sent by FW to indicate high temperature
as detected by one of the sensors on the board.
Add handling of this event by writing the numbers of the alert sensors
to the kernel log.
Signed-off-by: NIlan Tayari <ilant@mellanox.com>
Signed-off-by: NAdi Nissim <adin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add FORCE_PAUSE bit to force local pause settings instead
of using auto negotiated values.
Signed-off-by: NSantosh Rastapur <santosh@chelsio.com>
Signed-off-by: NCasey Leedom <leedom@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since there's no special support for the bridge events, the driver
returns -EOPNOTSUPP, and thus the commit never happens. Therefore
schedule respin during the prepare stage: there's no real difference one
way or another.

This fixes the problem that mirror-to-gretap offload wouldn't adapt to
changes in bridge vlan configuration right away and another notification
would have to arrive for mlxsw to catch up.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A follow-up patch enables emitting VLAN notifications for the bridge CPU
port in addition to the existing slave port notifications. These
notifications have orig_dev set to the bridge in question.

Because there's no specific support for these VLANs, just ignore the
notifications to maintain the current behavior.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A follow-up patch enables emitting VLAN notifications for the bridge CPU
port in addition to the existing slave port notifications. These
notifications have orig_dev set to the bridge in question.

Because there's no specific support for these VLANs, just ignore the
notifications to maintain the current behavior.
Signed-off-by: NPetr Machata <petrm@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds driver changes for capturing the link change count in
ethtool statistics display.

Please consider applying this to "net-next".
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove and coalesce formats when there is an unnecessary
character after a logging newline.  These extra characters
cause logging defects.

Miscellanea:

o Coalesce formats
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test-building this driver on targets without CONFIG_OF revealed a build
failure:

drivers/net/ethernet/ti/davinci_mdio.c: In function 'davinci_mdio_probe':
drivers/net/ethernet/ti/davinci_mdio.c:380:9: error: implicit declaration of function 'davinci_mdio_probe_dt'; did you mean 'davinci_mdio_probe'? [-Werror=implicit-function-declaration]

This adjusts the #ifdef logic in the driver to make it build in
all configurations.

Fixes: 2652113f ("net: ethernet: ti: Allow most drivers with COMPILE_TEST")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSekhar Nori <nsekhar@ti.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

While compile-testing on arm64 with gcc-8.1, I ran into a build diagnostic:

drivers/net/ethernet/freescale/fec_main.c: In function 'fec_probe':
drivers/net/ethernet/freescale/fec_main.c:3517:25: error: '%d' directive writing between 1 and 10 bytes into a region of size 5 [-Werror=format-overflow=]
   sprintf(irq_name, "int%d", i);
                         ^~
drivers/net/ethernet/freescale/fec_main.c:3517:21: note: directive argument in the range [0, 2147483646]
   sprintf(irq_name, "int%d", i);
                     ^~~~~~~
drivers/net/ethernet/freescale/fec_main.c:3517:3: note: 'sprintf' output between 5 and 14 bytes into a destination of size 8
   sprintf(irq_name, "int%d", i);
   ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~

It appears this has never shown on ppc32 or arm32 for an unknown reason, but
now gcc fails to identify that the 'irq_cnt' loop index has an upper bound
of 3, and instead uses a bogus range.

To work around the warning, this changes the sprintf to snprintf with the
correct buffer length.

Fixes: 78cc6e7e ("net: ethernet: freescale: Allow FEC with COMPILE_TEST")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NFugang Duan <fugang.duan@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As we keep the offloaded TC rules for NIC and e-switch in two different
places, make sure to return the number of offloaded flows according
to the use-case and not blindly from the priv.

Fixes: 655dc3d2 ('net/mlx5e: Use shared table for offloaded TC eswitch flows')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reported-by: NPaul Blakey <paulb@mellanox.com>
Reviewed-by: NPaul Blakey <paulb@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

When mlx5_fpga_conn_unmap_buf is called buf->sg[0].size
should equal the actual buffer size, not the message size.
Otherwise we will trigger the following dma debug warning
"DMA-API: device driver frees DMA memory with different size"

Fixes: 537a5057 ('net/mlx5: FPGA, Add high-speed connection routines')
Signed-off-by: NIlya Lesokhin <ilyal@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Properly initialize dma direction on fpga conn send.
Do not rely on dma_dir == 0 (DMA_BIDIRECTIONAL).
Signed-off-by: NIlya Lesokhin <ilyal@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

In the case that the reported max number of QPs capability
equals to zero, abort FPGA init.
Signed-off-by: NYevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: NAdi Nissim <adin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add print of the following values on init:
1. ieee vendor id
2. sandbox product id
3. sandbox product version
Signed-off-by: NIlan Tayari <ilant@mellanox.com>
Signed-off-by: NAdi Nissim <adin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add device name for Mellanox FPGA devices.
Signed-off-by: NIlan Tayari <ilant@mellanox.com>
Signed-off-by: NAdi Nissim <adin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add doxygen comments for enum mlx5_fpga_access_type.
Signed-off-by: NIlan Tayari <ilant@mellanox.com>
Signed-off-by: NAdi Nissim <adin@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

So far, the PCI BAR0 register is used for triggering FW reset. However,
that is a legacy attitude and it is recommended to use MRSR to perform
reset instead. So do that. Move the reset into init() function as
the cmd interface needs to be used. With that, IRQ initialization needs
to be moved as well. As a side effect, the reset move simplifies
the devlink reload flow.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is an exception in command interface processing in case the MRSR
register is written to. The register triggers FW reset and during the
reset FW returns an error. So handle this by ignoring this error while
writing to MRSR register.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit "net: qcom/emac: Encapsulate sgmii ops under one structure"
introduced the sgmii_ops structure, but did not correctly initialize
it on device tree platforms.  This resulted in compiler warnings when
ACPI is not enabled.
Reported-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NTimur Tabi <timur@codeaurora.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With CONFIG_TLS=m and MLX5_CORE_EN=y, we get a link failure:

drivers/net/ethernet/mellanox/mlx5/core/en_accel/tls_rxtx.o: In function `mlx5e_tls_handle_ooo':
tls_rxtx.c:(.text+0x24c): undefined reference to `tls_get_record'
drivers/net/ethernet/mellanox/mlx5/core/en_accel/tls_rxtx.o: In function `mlx5e_tls_handle_tx_skb':
tls_rxtx.c:(.text+0x9a8): undefined reference to `tls_device_sk_destruct'

This narrows down the dependency to only allow the configurations
that will actually work. The existing dependency on TLS_DEVICE is
not sufficient here since MLX5_EN_TLS is a 'bool' symbol.

Fixes: c83294b9 ("net/mlx5e: TLS, Add Innova TLS TX support")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Acked-by: NBoris Pismenny <borisp@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

the message be freed immediately, no need to trim it
back to the previous size.

Inspired by commit 7a9b3ec1 ("nl80211: remove unnecessary genlmsg_cancel() calls")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report the stat diff to make sure MQ stats add up to child stats.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for MQ offload and setting RED parameters
on queue-by-queue basis.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allocate the PF representor as multi-queue to allow setting
the configuration per-queue.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a handful of statistics exposing some internal details
of the implementation.  Expose those via ethtool.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow nfp apps to add extra ethtool stats.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Report basic and extended RED statistics back to TC.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: NDirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Offload simple RED configurations.  For now support only DCTCP
like scenarios where min and max are the same.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Queue levels for simple ECN marking are stored in _abi_nfd_out_q_lvls_X
symbol, where X is the PCIe PF id.  Find out the location of that symbol
and add helpers for modifying it.
Signed-off-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>