The manager table is empty by default. If it is not initialized, the
management pkgs like LLDP will be dropped by hardware. Default entries
need to be added to manager table.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds get_regs support for ethtool cmd.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If the int_gl_idx does not be set, the default interrupt coalesce index
is 0. The TX queues and the RX queues will both use the GL0 as the
interrupt coalesce GL switch. But it should be GL1 for TX queues and GL0
for RX queues.

This patch adds the int_gl_idx setup for TX queues and RX queues.

Fixes: 76ad4f0e ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The statistics of rx/tx packets size greater than 1518
are not detailed. This patch adds more statistics for
different packet size range.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pause parameters include source address, transmit gap and pause time.
The default value of the pause source address is zero in the hardware.
Default pause parameters need to be set to the hardware. Also, when
setting new mac address, the pause source address need to be updated.

Fixes: 9dc2145d ("net: hns3: Add support for PFC setting in TM module")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When initializing the MAC, the MTU vlaue need to be set to the hardware
too. Otherwise, the MTU value of software will be different from the MTU
value of hardware.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When setting MTU, actually what we do is configuring the max frame size
for the hardware. ETH_HLEN、ETH_FCS_LEN and VLAN_HLEN must need to be
considered. And the frame size which is less than the default value
should not be set to the hardware. Because in the hardware, the the max
frame size not only controls the RX packet size, but also controls the
TX packet size. the RX packets whose size are greater than the setting
value will be dropped.

This patch fixes the bug setting a error max frame size to hardware.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit a9c782822166 ("net: hns3: add support for set_pauseparam")
adds set_pauseparam support for ethtool cmd, but forgets to update
fc_mode_last_time when PFC mode is disabled in hclge_cfg_pauseparam().
The wrong fc_mode_last_time will be used to update flow control mode
when lldpad has been running. As a result, when using the ethtool
command "-a", user will get a wrong pause parameter.

This patch adds the fc_mode_last_time update when PFC mode is disabled.

Fixes: a9c782822166 ("net: hns3: add support for set_pauseparam")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The result of tqp statistics query was read with an
error position, fix it according to the user manual.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It takes more than 200 query response messages between
driver and IMP, while updating the packet statistics.
It's too heavy for IMP to update it per second.

Extend the update period of packet statistics data from
1 second to 300 seconds(if too long, the statistics may
overflow).

As a result, we need to update it while querying with
ifconfig tool to keep the statistics data fresh.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The igu_rx_err_pkt indicates the same error with
mac_rx_fcs_err_pkt_num, so remove it.

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix spelling error "overrsize" --> "oversize".

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some members of packet statistics are named in different styles.
This patch unifies them with new internal name rules, the main
modification are below:
trans --> tx
rcv --> rx
rcb_q%d_tx -->  txq#%d
rcb_q%d_rx -->  rxq#%d
sw_err_cnt(tx side) --> tx_dropped
sw_err_cnt(rx side) --> rx_dropped
pkts --> packets
tx_err_cnt --> errors
rx_err_cnt --> errors
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds vlan filter enable switch to
support ethtool -K ethX rx-vlan-filter on/off.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

TC-based sched mode supports SRIOV enabled and SRIOV disabled. This
patch change the TM sched mode to TC-based mode in initialization
process.

Fixes: cc9bb43a ("net: hns3: Add tc-based TM support for sriov enabled port")
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Burstiness of a flow is determined by the depth of a bucket, When the
upper rate of shaper is large, the current depth of a bucket is not
enough.

The default upper rate of shaper is 100G, so increase the depth of
a bucket according to UM.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for querying advertised pause frame by using
ethtool command(ethtool ethx).

Fixes: 496d03e9 ("net: hns3: Add Ethtool support to HNS3 driver")
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

commit c4fb2cdf575d ("net: hns3: fix a bug for phy supported feature
initialization") adds default supported features for phy, but our hardware
also supports Asym Pause. This patch adds Asym Pause support to phy
default features to prevent Asym Pause can not be advertised when the phy
negotiates flow control.

Fixes: c4fb2cdf575d ("net: hns3: fix a bug for phy supported feature initialization")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When auto-negotiation is enabled, the MAC flow control settings is
based on the flow control negotiation result. And it should be configured
after a valid link has been established. This patch adds support to update
flow control settings after auto-negotiation has completed.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds set_pauseparam support for ethtool cmd.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When phy exists, we use the value of phydev.autoneg to represent the
auto-negotiation state of hardware. Otherwise, we use the value of
mac.autoneg to represent it.

This patch fixes for getting a error value of auto-negotiation state in
hclge_get_autoneg().

Fixes: 46a3df9f ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support")
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When checking whether auto-negotiation is on, driver only needs to
check the value of mac.autoneg(SW) directly, and does not need to
query it from hardware. Because this value is always synchronized
with the auto-negotiation state of hardware.

This patch removes the mac auto-negotiation state query.
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds offload command related to "ethtool -K".
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds vlan offload config commands, initializes
the rules of tx/rx vlan tag handle for hw.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sets vlan masked, in order to avoid the received
packets being filtered.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add configuration for rss_size_max in hdev but not hardcode it.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NMingguang Qu <qumingguang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the support to change tqps number for PF driver
by using ehtool -L command.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NMingguang Qu <qumingguang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the support to query tqps number for PF driver
by using ehtool -l command.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NMingguang Qu <qumingguang@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All PF mailbox events are conveyed through a common interrupt
(vector 0). This interrupt vector is shared by reset and mailbox.

This patch adds the handling of mailbox interrupt event and its
deferred processing in context to a separate mailbox task.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is required to support ring-vector binding and reset
of TQPs requested by the VF driver to the PF driver. Mailbox
handler is added with corresponding VF commands/messages to
handle the request.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Command queue provides the provision of Mailbox command which
can be used for communication between PF and VF. PF handles
messages from various VFs for fetching various information like,
queue, vlan, link status related etc. It also handles the request
from various VFs to perform certain privileged operations.

This patch adds the support of a message handler for handling
such various command requests from VF.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Most of the NAPI handling interface, skb buffer management,
management of the RX/TX descriptors, ethool interface etc.
has quite a bit of code which is common to VF and PF driver.

This patch makes the exisitng PF's HNS3 ENET driver as the
common ENET driver for both Virtual & Physical Function. This
will help in reduction of redundancy and better management of
code.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In exisiting code, the way to detect if driver/client reset should
be executed or if hardware should be be soft resetted was overly
complex.

Existing code use to read the interrupt status register from task
context to figure out if the interrupt source event was reset and
then use clear the interrupt source for reset while waiting for the
hardware to finish the reset. This behaviour again was confusing
and overly complex in terms of the flow.

This patch simplifies the handling of the requested reset and the
pending reset(i.e. reset which have already been asserted by the
software and hardware has acknowledged back to driver that it is
processing the hardware reset through interrupt)
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Existing common service task was being used to service the reset
requests. This patch tries to make the handling of reset cleaner
by separating task to handle the reset requests. This might in
turn help in adapting similar handling approach for other
interrupt events like mailbox, sharing vector 0 interrupt.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The reset interrupt event shares common miscellaneous interrupt
Vector 0. In the existing reset interrupt handling we disable
the Vector 0 interrupt in misc interrupt handler and re-enable
them later in context to common service task.

This also means other event sources like mailbox would also be
deferred or if the interrupt event was due to mailbox(which shall
be supported for VF soon), it could delay the reset handling.

This patch reorganizes the reset interrupt handling logic and
makes it more fair to other events.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: Nlipeng <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch migrates the HNS3 driver code from use of depricated PCI
MSI/MSI-X interrupt vector allocation/free APIs to new common APIs.
Signed-off-by: NSalil Mehta <salil.mehta@huawei.com>
Suggested-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When checking whether auto-negotiation is on, driver only needs to
check the value of mac.autoneg(SW) directly, and does not need to
query it from hardware. Because this value is always synchronized
with the auto-negotiation state of hardware.

This patch removes mac auto-negotiation state query in
hclge_update_speed_duplex().

Fixes: 46a3df9f (net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support)
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver gets phy address from NCL_config file and uses the phy address
to initialize phydev. There are 5 bits for phy address. And C22 phy
address has 5 bits. So 0-31 are all valid address for phy. If there
is no phy, it will crash. Because driver always get a valid phy address.

This patch fixes the phy address to 8 bits, and use 0xff to indicate
invalid phy address.

Fixes: 46a3df9f (net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support)
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Change TC_SETUP_MQPRIO to TC_SETUP_QDISC_MQPRIO to match the new
convention.
Signed-off-by: NNogah Frankel <nogahf@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a bug for phy supported feature initialization.
Currently, the value of phydev->supported is initialized by kernel.
So it includes many features that we do not support, such as
SUPPORTED_FIBRE and SUPPORTED_BNC. This patch fixes it.

Fixes: 256727da (net: hns3: Add MDIO support to HNS3 Ethernet driver for hip08 SoC)
Signed-off-by: NFuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: NLipeng <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>