opregion-based platforms will send ACPI video event 0x80 for a range of
notification types for legacy compatibility. This is interpreted as a
display switch event, which may not be appropriate in the circumstances.
When we receive such an event we should make sure that the platform is
genuinely requesting a display switch before passing that event through
to userspace.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Tested-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NKeith Packard <keithp@keithp.com>

Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The opregion is a shared memory region between ACPI and the graphics
driver. As the ACPI mapping has been changed to cachable in commit
6d5bbf00, mapping the intel opregion
non-cachable now fails. As no bus-master hardware is involved in the
opregion, cachable map should do no harm.

Tested on a Fujitsu Lifebook P8010.
Signed-off-by: NMichael Karcher <kernel@mkarcher.dialup.fu-berlin.de>
[ickle: convert to acpi_os_ioremap for consistency]
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Admittedly, trusting ACPI or the BIOS at all to be correct is littered
with numerous examples where it is wrong. Maybe, just maybe, we will
have better luck using the ACPI OpRegion lid status...
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

The bulk of the change is to convert the growing list of rings into an
array so that the relationship between the rings and the semaphore sync
registers can be easily computed.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

In case of an opregion signature mismatch in intel_opregion_setup(),
iounmap the correct address.
Signed-off-by: NChristoph Fritz <chf.fritz@googlemail.com>
Cc: stable@kernel.org
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

There were two instances of code to control the panel backlight and
neither handled the complete set of device variations.

Fixes:

  Bug 29716 - [GM965] Regression: Backlight resets to minimum when changing resolution
  https://bugs.freedesktop.org/show_bug.cgi?id=29716

And a bug on one of my PineView boxes which overflowed the backlight
value.

Incorporates part of a similar patch by Matthew Garrett that exposes a
native Intel backlight controller.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

It is recommended that we use the Video BIOS tables that were copied
into the OpRegion during POST when initialising the driver. This saves
us from having to furtle around inside the ROM ourselves and possibly
allows the vBIOS to adjust the tables prior to initialisation.

On some systems, such as the Samsung N210, there is no accessible VBIOS
and the only means of finding the VBT is through the OpRegion.

v2: Rearrange the code so that ASLE is enabled along with ACPI
v3: Enable OpRegion parsing even without ACPI
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Matthew Garrett <mjg@redhat.com>

It's part of the generic Intel driver infrastructure so rename it in
prepreparation for using it for VBT.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

If i915 opregion is present, the acpi_video driver doesn't register
itself immediately; it defers that until the i915 opregion code is done.
But if that *fails*, the acpi_video driver was never getting registered.
And thus I have no backlight support on my Lenovo IdeaPad S10-3.

Call acpi_video_register() on the failure path, and it works again.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Acked-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: NMatthew Garrett <mjg@redhat.com>

Within i915_opregion.c there are two blocks of semantically identical
ASLE response codes defined. Only one of those matches the ACPI IGD
OpRegion Specification 0.1, use those.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NMatthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: NEric Anholt <eric@anholt.net>

we used to set the DIDL in the output device detected order.
But some BIOSes requires it to be initialized in the ACPI device order.
e.g. the value of the first field in DIDL stands for the first
ACPI video output device in ACPI namespace.

Now we initialize the DIDL using the device id, i.e. _ADR return value,
of each ACPI video device, if it is not 0.
https://bugzilla.kernel.org/show_bug.cgi?id=15054Signed-off-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

IGD* isn't a useful name.  Replace with the codenames, as sourced from
pci.ids.
Signed-off-by: NAdam Jackson <ajax@redhat.com>
[anholt: Fixed up for merge with pineview/ironlake changes]
Signed-off-by: NEric Anholt <eric@anholt.net>

Add the support of ACPI opregion on Ironlake so that the backlight
brightness can be adjusted by using ACPI interface
   >/sys/class/backlight/acpi_video0/brightness
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Tested-by: NZhao Yakui <yakui.zhao@intel.com>
[zhenyuw: cleanups, fix typo for checking GSE irq and convert to
current irq handling logic.]
Signed-off-by: NZhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Replace the DRM_DEBUG with DRM_DEBUG_DRIVER in generic i915 driver.
Then the debug info can be obtained by adding the boot option of
"drm.debug=0x02".

At the same time the debug info in increase/decrease clock is also
printed by using DRM_DEBUG_DRIVER instead of DRM_DEBUG_KMS.
Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

BLC_PWM_CTL2 is for 965+ only, so add device model check for
legacy backlight control.

For native backlight control, it maps the backlight value (0~255)
in opregion ASLE[BCLP] to backlight duty cycle (0~max_backlight)
and set into control register.

It also add support for IGD device, which follows opregion spec.
Signed-off-by: NLi Peng <peng.li@intel.com>
Signed-off-by: NJesse Barnes <jbarnes@virtuousgeek.org>

Sometimes both acpi video and i915 driver are compiled as modules.
And there exists the strict dependency between the two drivers.
The acpi video bus will be unloaded in course of unloading the i915 driver.
If we unload the acpi video driver, then the kernel oops will be triggered.

Add the reference count to avoid unloading the ACPI video bus twice.
The reference count should be checked before unregistering the acpi video bus.
If the reference count is already zero, it won't unregister it again.
And after the acpi video bus is already unregistered, the reference count
will be set to zero.

http://bugzilla.kernel.org/show_bug.cgi?id=13396Signed-off-by: NZhao Yakui <yakui.zhao@intel.com>
Acked-by: NZhang Rui <rui.zhang@intel.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The ACPI video driver defers registration to the i915 driver if the
system supports opregion-mediated backlight control. This registration
was only being performed in the KMS case. Ensure it's done even if we
don't have modesetting enabled.

http://bugzilla.kernel.org/show_bug.cgi?id=13048Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NLen Brown <len.brown@intel.com>

The changes to opregion initialisation order meant that the ASLE setup
code might not be run at the correct time. Ensure that the interrupts are
set up.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

The i915 DRM triggers registration of the ACPI video driver on load. It
should unregister it at unload in order to avoid generating backtraces on
being reloaded.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

The ACPI video driver defers registration to the i915 driver if the
system supports opregion-mediated backlight control. This registration
was only being performed in the KMS case. Ensure it's done even if we
don't have modesetting enabled.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NEric Anholt <eric@anholt.net>

Intel graphics hardware that implements the ACPI IGD OpRegion spec
requires that the list of display devices be populated before any ACPI
video methods are called. Detect when this is the case and defer
registration until the opregion code calls it. Fixes crashes on HP
laptops.

http://bugzilla.kernel.org/show_bug.cgi?id=11259Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Acked-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NLen Brown <len.brown@intel.com>

Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@linux.ie>

The pipestat fields affect reporting of all vblank-related interrupts, so we
have to reset them during the irq_handler, and while enabling vblank
interrupts.  Otherwise, if a pipe status field had been set to non-zero
before enabling reporting, we would never see an interrupt again.

This patch adds i915_enable_pipestat and i915_disable_pipestat to abstract
out the steps needed to change the reported interrupts.
Signed-off-by: NKeith Packard <keithp@keithp.com>
Signed-off-by: NEric Anholt <eric@anholt.net>
Signed-off-by: NDave Airlie <airlied@redhat.com>

This adds the support necessary for allowing ACPI backlight control to
work on some newer Intel-based graphics systems. Tested on Thinkpad T61
and HP 2510p hardware.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NDave Airlie <airlied@linux.ie>