The same check is placed twice in fimd/decon_update_plane(), remove
one of them.
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Get rid of legacy DRM vblank function that are less clear to use.
The new ones basically requires only the crtc as parameters.

It also clean ups exynos_drm_crtc_finish_pageflip() parameters as a
consequence.
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Instead of giving -1 to as arg to  drm_send_vblank_event() pass the
correct pipe number to it.
Signed-off-by: NGustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

This is simplest solution about reported problem[1]. It's no problem to
clear channel only when iommu is enabled, if we consider that we cannot
recognize iommu errors when iommu is disabled and it have been valid
until now. But this cannot be nice solution.

[1] https://lkml.org/lkml/2015/7/21/404Reported-by: NKrzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Already drm_iommu_attach_device checks whether support iommu internally.
It should clear channels always regardless iommu support. We didn't know
because we can detect the problem when iommu is enabled, so we don't
have to use drm_iommu_attach_device_if_possible and then we can remove
drm_iommu_attach_device_if_possible and clear_channels function pointer.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The vidi is virtual kms driver and now it is registered earlier than
actual hw kms drivers, so it will occupy crtc index 0. Some users
assume the condition yet that actual hw kms driver has crtc index 0.
It may or may not be matter but let's arrange register order.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Driver uses only VSYNC interrupts, so we need to cache VSYNC bit state only.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The driver uses bool protected by mutex to track power state.
The patch replaces this combo with single bit and atomic bitops.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Already drm_iommu_attach_device and drm_iommu_detach_device check
whether support iommu internally, so we don't have to call
is_drm_iommu_supported before call them.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

If CONFIG_ARM_DMA_USE_IOMMU is disable, CONFIG_DRM_EXYNOS_IOMMU also is
disable. When CONFIG_DRM_EXYNOS_IOMMU is disable,
is_drm_iommu_supported() returns always false, so we can remove to use
ifdef CONFIG_ARM_DMA_USE_IOMMU in is_drm_iommu_supported().
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Tested-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The unique results of all the combination of rotation and flip can
be represented by just 8 states. This patch handles all the combination
correctly.
Signed-off-by: NHyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch removes intermediate struct for HDMIv14 register configuration,
instead registry values are calculated on the fly.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch removes intermediate struct for HDMIv13 register configuration,
instead registry values are calculated on the fly.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch removes redundant fields from hdmi_conf_regs. Their values
can be calculated from current_mode. This patch is the first step to remove
whole hdmi_conf_regs structure.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The patch replaces duplicated driver data fields in private context with
pointer to driver data. It also simplifies driver data lookup code.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Most of the code is called by drm core framework, so it is already synchronized.
The only async function is irq routine which only calls drm framework so it
does not need to be synchronized.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

GPIO is tested only in hdmi_detect, so there is no reason to set it in
other places and to preserve its value in context.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

s5p_hdmi_platform_data were used before device tree introduction.
As HDMI driver is DT only we can drop this struct completely.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Once pm_runtime_set_active() gets called, the kernel assumes that given
device has already enabled runtime pm and will call pm_runtime_suspend()
without matching pm_runtime_resume(). In case of DRM FIMC IPP driver,
this will result in calling clk_disable() without respective call to
clk_enable(). This patch removes call to pm_runtime_set_active() to
ensure that pm_runtime_suspend/resume calls will match.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

INT_EN cache field was updated only by mixer_enable_vblank.
The patch adds update also by mixer_disable_vblank function.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Specification advises to clear vsync indicator before configuring vsync.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The driver used incorrect flags to clear interrupt status.
The patch fixes it.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

edid returned by drm_get_edid should be freed.
The patch fixes it.
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

The bits for rotation are not used as exclusively. So GSC_IN_ROT_270 can
not be used for swap detection. The definition of it is same with
GSC_IN_ROT_MASK. It is enough to check GSC_IN_ROT_90 bit is set or not to
check whether width / height size swapping is needed.
Signed-off-by: NHyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: NInki Dae <inki.dae@samsung.com>

Instead of using the legacy VBLANK API, use the new KMS API. This is
part of an effort to convert all existing users so that the KMS API can
be changed to properly use per-CRTC data.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some of the functions are documented inconsistently. Add Returns:
sections where missing and use consistent style to describe the return
value.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Name all references to the pipe number (CRTC index) consistently to make
it easier to distinguish which is a pipe number and which is a pointer
to struct drm_crtc.

While at it also make all references to the pipe number unsigned because
there is no longer any reason why it should ever be negative.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When accessing the array of per-CRTC VBLANK structures we must always
check that the index into the array is valid before dereferencing to
avoid crashing.
Signed-off-by: NThierry Reding <treding@nvidia.com>
[danvet: Squash in my own whitespace ocd fixup in drm_vblank_count.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The drm_send_vblank_event() function treats negative CRTC indices as
meaning that a driver doesn't have proper VBLANK handling. This is the
only place where DRM needs negative CRTC indices, so in order to enable
subsequent cleanup, remove this special case and replace it by the more
obvious check for whether or not VBLANK support was initialized.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Rather than a mix of the the sized uint32_t and signed integer, use an
unsized unsigned int to specify the format count.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

debugfs_remove() gracefully ignores NULL parameters, so the explicit
checks can be removed.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Wrap overly long lines to make checkpatch happy. While at it, also add
blank lines after declarations to eliminate additional problems flagged
by checkpatch.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Use pr_fmt() to define the "vga_switcheroo: " prefix that is prepended
to all output messages emitted by pr_*() functions. This allows making
existing strings much shorter and eliminates a bunch of warnings from
checkpatch about lines being overly long.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The header comment uses a weird combination of formatting styles. Make
it consistent.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This silences a bunch of checkpatch warnings and makes the code shorter.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Wrap overly long lines (offending lines were mostly comments, so trivial
to fix up) and a number of other coding style issues pointed out by the
checkpatch tool.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Define the pr_fmt() macro to causes all messages emitted by pr_*()
functions to be prefixed with "vgaarb: ".
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Some setups do not register a default VGA device, in which case the VGA
arbiter will still complain about the (non-existent) PCI device being a
non-VGA device.

Fix this by making the error message conditional on a default VGA device
having been set up. Note that the easy route of erroring out early isn't
going to work because otherwise priv->target won't be properly updated.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This patch fixes null pointer access incurred when
encoder driver didn't set its own mode_fixup callback.

mode_fixup callback shoudn't be called if the callback
of drm_encoder_helper_funcs is NULL.

Changelog v2:
- change it to else if
Signed-off-by: NInki Dae <inki.dae@samsung.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Instead of our own duplicated one. This fixes a bug in the driver
unload code if DRM_FBDEV_EMULATION=n but DRM_I915_FBDEV=y because we
try to unregister the nonexistent fbdev drm_framebuffer.

Cc: Archit Taneja <architt@codeaurora.org>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reported-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>