This enables scanning pages in fixed interval to determine their access
frequency (hot/cold). The result is exported to user land on basis of
memory cgroup by "memory.idle_page_stats". The design is highlighted as
below:

   * A kernel thread is spawn when this feature is enabled by writing
     non-zero value to "/sys/kernel/mm/kidled/scan_period_in_seconds".
     The thread sequentially scans the nodes and their pages that have
     been chained up in LRU list.

   * For each page, its corresponding age information is stored in the
     page flags or array in node. The age represents the scanning intervals
     in which the page isn't accessed. Also, the page flag (PG_idle) is
     leveraged. The page's age is increased by one if the idle flag isn't
     cleared in two consective scans. Otherwise, the page's age is cleared out.
     Also, the page's age information is cleared when it's free'd so that
     the stale age information won't be fetched when it's allocated.

   * Initially, the flag is set, while the access bit in its PTE is cleared
     out by the thread. In next scanning period, its PTE access bit is
     synchronized with the page flag: clear the flag if access bit is set.
     The flag is kept otherwise. For unmapped pages, the flag is cleared
     when it's accessed.

   * Eventually, the page's aging information is updated to the unstable
     bucket of its corresponding memory cgroup, taking as statistics. The
     unstable bucket (statistics) is copied to stable bucket when all pages
     in all nodes are scanned for once. The stable bucket (statistics) is
     exported to user land through "memory.idle_page_stats".

TESTING
=======

   * cgroup1, unmapped pagecache

     # dd if=/dev/zero of=/ext4/test.data oflag=direct bs=1M count=128
     #
     # echo 1 > /sys/kernel/mm/kidled/use_hierarchy
     # echo 15 > /sys/kernel/mm/kidled/scan_period_in_seconds
     # mkdir -p /cgroup/memory
     # mount -tcgroup -o memory /cgroup/memory
     # echo 1 > /cgroup/memory/memory.use_hierarchy
     # mkdir -p /cgroup/memory/test
     # echo 1 > /cgroup/memory/test/memory.use_hierarchy
     #
     # echo $$ > /cgroup/memory/test/cgroup.procs
     # dd if=/ext4/test.data of=/dev/null bs=1M count=128
     # < wait a few minutes >
     # cat /cgroup/memory/test/memory.idle_page_stats | grep cfei
     # cat /cgroup/memory/test/memory.idle_page_stats | grep cfei
       cfei   0   0   0   134217728   0   0   0   0
     # cat /cgroup/memory/memory.idle_page_stats | grep cfei
       cfei   0   0   0   134217728   0   0   0   0

   * cgroup1, mapped pagecache

     # < create same file and memory cgroups as above >
     #
     # echo $$ > /cgroup/memory/test/cgroup.procs
     # < run program to mmap the whole created file and access the area >
     # < wait a few minutes >
     # cat /cgroup/memory/test/memory.idle_page_stats | grep cfei
       cfei   0   134217728   0   0   0   0   0   0
     # cat /cgroup/memory/memory.idle_page_stats | grep cfei
       cfei   0   134217728   0   0   0   0   0   0

   * cgroup1, mapped and locked pagecache

     # < create same file and memory cgroups as above >
     #
     # echo $$ > /cgroup/memory/test/cgroup.procs
     # < run program to mmap the whole created file and mlock the area >
     # < wait a few minutes >
     # cat /cgroup/memory/test/memory.idle_page_stats | grep cfui
       cfui   0   134217728   0   0   0   0   0   0
     # cat /cgroup/memory/memory.idle_page_stats | grep cfui
       cfui   0   134217728   0   0   0   0   0   0

   * cgroup1, anonymous and locked area

     # < create memory cgroups as above >
     #
     # echo $$ > /cgroup/memory/test/cgroup.procs
     # < run program to mmap anonymous area and mlock it >
     # < wait a few minutes >
     # cat /cgroup/memory/test/memory.idle_page_stats | grep csui
       csui   0   0   134217728   0   0   0   0   0
     # cat /cgroup/memory/memory.idle_page_stats | grep csui
       csui   0   0   134217728   0   0   0   0   0

   * Rerun above test cases in cgroup2 and the results are no exceptional.
     However, the cgroups are populated in different way as below:

     # mkdir -p /cgroup
     # mount -tcgroup2 none /cgroup
     # echo "+memory" > /cgroup/cgroup.subtree_control
     # mkdir -p /cgroup/test
Signed-off-by: NGavin Shan <shan.gavin@linux.alibaba.com>
Reviewed-by: NYang Shi <yang.shi@linux.alibaba.com>
Reviewed-by: NXunlei Pang <xlpang@linux.alibaba.com>

Introduce a new interface, wmark_scale_factor, which defines the
distance between wmark_high and wmark_low.  The unit is in fractions of
10,000. The default value of 50 means the distance between wmark_high
and wmark_low is 0.5% of the max limit of the cgroup.  The maximum value
is 1000, or 10% of the max limit.

The distance between wmark_low and wmark_high have impact on how hard
memcg kswapd would reclaim.
Reviewed-by: NGavin Shan <shan.gavin@linux.alibaba.com>
Reviewed-by: NXunlei Pang <xlpang@linux.alibaba.com>
Signed-off-by: NYang Shi <yang.shi@linux.alibaba.com>

The global kswapd could set memory node to dirty or writeback if current
scan find all pages are unqueued dirty or writeback.  Then kswapd would
write out dirty pages or wait for writeback done.  The memcg kswapd
behaves like global kswapd, and it should set dirty or writeback state
to memcg too if the same condition is met.

Since direct reclaim can't write out page caches, the system depends on
kswapd to write out dirty pages if scan finds too many dirty pages in
order to avoid pre-mature OOM.  But, if page cache is dirtied too fast,
writing out pages definitely can't catch up with dirtying pages.  It is
the responsibility of dirty page balance to throttle dirtying pages.
Reviewed-by: NGavin Shan <shan.gavin@linux.alibaba.com>
Reviewed-by: NXunlei Pang <xlpang@linux.alibaba.com>
Signed-off-by: NYang Shi <yang.shi@linux.alibaba.com>

Since background water mark reclaim is scheduled by workqueue, it could
do more work than direct reclaim, i.e. write out dirty page, etc.

So, add PF_KSWAPD flag, so that current_is_kswapd() would return true
for memcg background reclaim.  The condition "current_is_kswapd() &&
!global_reclaim(sc)" is good enough to tell current is global kswapd or
memcg background reclaim.

And, kswapd is not allowed to break memory.low protection for now, memcg
kswapd should not break it either.
Reviewed-by: NGavin Shan <shan.gavin@linux.alibaba.com>
Reviewed-by: NXunlei Pang <xlpang@linux.alibaba.com>
Signed-off-by: NYang Shi <yang.shi@linux.alibaba.com>

Like v1, add background reclaim support for cgroup v2.  The interfaces
are exactly same with v1.  However, if high limit is setup for v2, the
water mark would be calculated by high limit instead of max limit.
Reviewed-by: NGavin Shan <shan.gavin@linux.alibaba.com>
Reviewed-by: NXunlei Pang <xlpang@linux.alibaba.com>
Signed-off-by: NYang Shi <yang.shi@linux.alibaba.com>

Currently when memory usage exceeds memory cgroup limit, memory cgroup
just can do sync direct reclaim.  This may incur unexpected stall on
some applications which are sensitive to latency.  Introduce background
async page reclaim mechanism, like what kswapd does.

Define memcg memory usage water mark by introducing wmark_ratio interface,
which is from 0 to 100 and represents percentage of max limit.  The
wmark_high is calculated by (max * wmark_ratio / 100), the wmark_low is
(wmark_high - wmark_high >> 8), which is an empirical value.  If wmark_ratio
is 0, it means water mark is disabled, both wmark_low and wmark_high is max,
which is the default value.

If wmark_ratio is setup, when charging page, if usage is greater than
wmark_high, which means the available memory of memcg is low, a work
would be scheduled to do background page reclaim until memory usage is
reduced to wmark_low if possible.

Define a dedicated unbound workqueue for scheduling water mark reclaim
works.
Reviewed-by: NGavin Shan <shan.gavin@linux.alibaba.com>
Reviewed-by: NXunlei Pang <xlpang@linux.alibaba.com>
Signed-off-by: NYang Shi <yang.shi@linux.alibaba.com>

AliOS Cloud Kernel has cgroup writeback support for v1, so the reclaim could be
treated as sane reclaim if cgwb_v1 is enabled.
Reviewed-by: NGavin Shan <shan.gavin@linux.alibaba.com>
Reviewed-by: NXunlei Pang <xlpang@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NCaspar Zhang <caspar@linux.alibaba.com>
Signed-off-by: NYang Shi <yang.shi@linux.alibaba.com>

Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

A performance regression is observed since linux v4.19 when we do aio
test using fio with iodepth 128 on overlayfs. And we found that queue
depth of the device is always 1 which is unexpected.

After investigation, it is found that commit 16914e6f
("ovl: add ovl_read_iter()") and commit 2a92e07e
("ovl: add ovl_write_iter()") use do_iter_readv_writev() to submit
requests to real filesystem. Async IOs are converted to sync IOs here
and cause performance regression.

So implement async IO for stacked reading and writing.

Changes since v1:
  - add a cleanup helper for completion/error handling
  - handle the case when aio_req allocation failed
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

This isn't cause any behavior changes and will be used by overlay
async IO implementation.
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

When events such as direct reclaim and oom occur intensively, soft
lockup is very likely to happen in the instances with 1 vcpu and with
kernel preempt disabled.

The example soft lockup is as follows.

[  160.555984] watchdog: BUG: soft lockup - CPU#0 stuck for 112s! [malloc:2188]
[  160.557975] Modules linked in: button
[  160.559495] CPU: 0 PID: 2188 Comm: malloc Not tainted 4.19.57-15.457.al7.x86_64 #1
[  160.561546] Hardware name: Alibaba Cloud Alibaba Cloud ECS, BIOS 3288b3c 04/01/2014
[  160.563707] RIP: 0010:shrink_node+0x1ae/0x450
[  160.565391] Code: 00 00 00 49 8b 4f 20 ba 01 00 00 00 4c 8b 74 24 10 4d 8b 47 28 49 8b 77 10 48 2b 4c 24 08 41 8b 7f 1c 4d8
[  160.570747] RSP: 0000:ffff9d0ec07a3b58 EFLAGS: 00000286 ORIG_RAX: ffffffffffffff13
[  160.572889] RAX: ffff982ab6014330 RBX: ffff982ab6014000 RCX: 0000000000000000
[  160.574992] RDX: 0000000000000001 RSI: ffff982ab6014000 RDI: ffff982ab6014000
[  160.577106] RBP: ffff982afffb6000 R08: 0000000000000000 R09: ffff982ab6014000
[  160.579219] R10: 0000000000000004 R11: 0000000000aaaaaa R12: 0000000000000000
[  160.581326] R13: 0000000000000000 R14: 0000000000000000 R15: ffff9d0ec07a3c50
[  160.583450] FS:  00007f8b414f7740(0000) GS:ffff982afda00000(0000) knlGS:0000000000000000
[  160.585704] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[  160.587662] CR2: 00007f8adb800010 CR3: 000000007ac9e001 CR4: 00000000003606b0
[  160.589835] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[  160.591971] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[  160.594133] Call Trace:
[  160.595602]  do_try_to_free_pages+0xcc/0x390
[  160.597356]  try_to_free_mem_cgroup_pages+0xf9/0x1d0
[  160.599198]  ? out_of_memory+0xb5/0x4a0
[  160.600882]  try_charge+0x244/0x750
[  160.602522]  ? __pagevec_lru_add_fn+0x1d0/0x330
[  160.604310]  mem_cgroup_try_charge+0xb4/0x1d0
[  160.606085]  mem_cgroup_try_charge_delay+0x1c/0x40
[  160.607892]  do_anonymous_page+0xf7/0x540
[  160.609574]  __handle_mm_fault+0x665/0xa00
[  160.611233]  ? __switch_to_asm+0x35/0x70
[  160.612838]  handle_mm_fault+0x122/0x1e0
[  160.614407]  __do_page_fault+0x1b7/0x470
[  160.615962]  do_page_fault+0x32/0x140
[  160.617474]  ? async_page_fault+0x8/0x30
[  160.619012]  async_page_fault+0x1e/0x30
[  160.620526] RIP: 0033:0x40068e

Fix it by adding cond_resched() in try_charge(), just before goto retry
after OOM_SUCCESS, in order to let OOM free some memory first.
Signed-off-by: NXu Yu <xuyu@linux.alibaba.com>
Reviewed-by: NYang Shi <yang.shi@linux.alibaba.com>
Reviewed-by: NXunlei Pang <xlpang@linux.alibaba.com>

Add a stat file to monitor the ioc_gq stat.
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

commit d256d796279de0bdc227ff4daef565aa7e80c898 upstream.

Single thread fio test (read, bs=4k, ioengine=libaio, iodepth=128,
numjobs=1) over dm-thin device has poor performance versus bare nvme
device.

Further investigation with perf indicates that queue_work_on() consumes
over 20% CPU time when doing IO over dm-thin device. The call stack is
as follows.

- 40.57% thin_map
    + 22.07% queue_work_on
    + 9.95% dm_thin_find_block
    + 2.80% cell_defer_no_holder
      1.91% inc_all_io_entry.isra.33.part.34
    + 1.78% bio_detain.isra.35

In cell_defer_no_holder(), wakeup_worker() is always called, no matter
whether the tc->deferred_bio_list list is empty or not. In single thread
IO model, this list is most likely empty. So skip waking up worker thread
if tc->deferred_bio_list list is empty.

Single thread IO performance improves from 448 MiB/s to 646 MiB/s (+44%)
once the needless wake_worker() calls are properly skipped.
Signed-off-by: NJeffle Xu <jefflexu@linux.alibaba.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

Currently in blk_throtl_bio(), if one bio exceeds its throtl_grp's bps
or iops limit, this bio will be queued throtl_grp's throtl_service_queue,
then obviously mm subsys will submit more pages, even underlying device
can not handle these io requests, also this will make large amount of pages
entering writeback prematurely, later if some process writes some of these
pages, it will wait for long time.

I have done some tests: one process does buffered writes on a 1GB file,
and make this process's blkcg max bps limit be 10MB/s, I observe this:
	#cat /proc/meminfo  | grep -i back
	Writeback:        900024 kB
	WritebackTmp:          0 kB

I think this Writeback value is just too big, indeed many bios have been
queued in throtl_grp's throtl_service_queue, if one process try to write
the last bio's page in this queue, it will call wait_on_page_writeback(page),
which must wait the previous bios to finish and will take long time, we
have also see 120s hung task warning in our server.

 INFO: task kworker/u128:0:30072 blocked for more than 120 seconds.
       Tainted: G            E 4.9.147-013.ali3000_015_test.alios7.x86_64 #1
 "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
 kworker/u128:0  D    0 30072      2 0x00000000
 Workqueue: writeback wb_workfn (flush-8:16)
  ffff882ddd066b40 0000000000000000 ffff882e5cad3400 ffff882fbe959e80
  ffff882fa50b1a00 ffffc9003a5a3768 ffffffff8173325d ffffc9003a5a3780
  00ff882e5cad3400 ffff882fbe959e80 ffffffff81360b49 ffff882e5cad3400
 Call Trace:
  [<ffffffff8173325d>] ? __schedule+0x23d/0x6d0
  [<ffffffff81360b49>] ? alloc_request_struct+0x19/0x20
  [<ffffffff81733726>] schedule+0x36/0x80
  [<ffffffff81736c56>] schedule_timeout+0x206/0x4b0
  [<ffffffff81036c69>] ? sched_clock+0x9/0x10
  [<ffffffff81363073>] ? get_request+0x403/0x810
  [<ffffffff8110ca10>] ? ktime_get+0x40/0xb0
  [<ffffffff81732f8a>] io_schedule_timeout+0xda/0x170
  [<ffffffff81733f90>] ? bit_wait+0x60/0x60
  [<ffffffff81733fab>] bit_wait_io+0x1b/0x60
  [<ffffffff81733b28>] __wait_on_bit+0x58/0x90
  [<ffffffff811b0d91>] ? find_get_pages_tag+0x161/0x2e0
  [<ffffffff811aff62>] wait_on_page_bit+0x82/0xa0
  [<ffffffff810d47f0>] ? wake_atomic_t_function+0x60/0x60
  [<ffffffffa02fc181>] mpage_prepare_extent_to_map+0x2d1/0x310 [ext4]
  [<ffffffff8121ff65>] ? kmem_cache_alloc+0x185/0x1a0
  [<ffffffffa0305a2f>] ? ext4_init_io_end+0x1f/0x40 [ext4]
  [<ffffffffa0300294>] ext4_writepages+0x404/0xef0 [ext4]
  [<ffffffff81508c64>] ? scsi_init_io+0x44/0x200
  [<ffffffff81398a0f>] ? fprop_fraction_percpu+0x2f/0x80
  [<ffffffff811c139e>] do_writepages+0x1e/0x30
  [<ffffffff8127c0f5>] __writeback_single_inode+0x45/0x320
  [<ffffffff8127c942>] writeback_sb_inodes+0x272/0x600
  [<ffffffff8127cf6b>] wb_writeback+0x10b/0x300
  [<ffffffff8127d884>] wb_workfn+0xb4/0x380
  [<ffffffff810b85e9>] ? try_to_wake_up+0x59/0x3e0
  [<ffffffff810a5759>] process_one_work+0x189/0x420
  [<ffffffff810a5a3e>] worker_thread+0x4e/0x4b0
  [<ffffffff810a59f0>] ? process_one_work+0x420/0x420
  [<ffffffff810ac026>] kthread+0xe6/0x100
  [<ffffffff810abf40>] ? kthread_park+0x60/0x60
  [<ffffffff81738499>] ret_from_fork+0x39/0x50

To fix this issue, we can simply limit throtl_service_queue's max queued
bios, currently we limit it to throtl_grp's bps_limit or iops limit, if it
still exteeds, we just sleep for a while.
Signed-off-by: NXiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Reviewed-by: NLiu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

Now we have counters for wait_time and service_time, but no completed
ios, so the average latency can not be measured.
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NXiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

This patch does the code cleanup because the seq_show handlers for tg
counters are the same. No functional changes.
Signed-off-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

Add 2 interfaces to stat io throttle information:
  blkio.throttle.total_io_queued
  blkio.throttle.total_bytes_queued

These interfaces are used for monitoring throttled io/bytes and
analyzing if delay has relation with io throttle.
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NGavin Shan <shan.gavin@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NXiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

io throtl stats will blkg_get at the beginning of throttle and then
blkg_put at the new introduced bi_tg_end_io. This will cause blkg to be
freed if end_io is called twice like dm-thin, which will save origin
end_io first, and call its overwrite end_io and then the saved end_io.
After that, access blkg is invalid and finally BUG:

[ 4417.235048] BUG: unable to handle kernel NULL pointer dereference at 00000000000001e0
[ 4417.236475] IP: [<ffffffff812e7c71>] throtl_update_dispatch_stats+0x21/0xb0
[ 4417.237865] PGD 98395067 PUD 362e1067 PMD 0
[ 4417.239232] Oops: 0000 [#1] SMP
......
[ 4417.274070] Call Trace:
[ 4417.275407]  [<ffffffff812ea93d>] blk_throtl_bio+0xfd/0x630
[ 4417.276760]  [<ffffffff810b3613>] ? wake_up_process+0x23/0x40
[ 4417.278079]  [<ffffffff81094c04>] ? wake_up_worker+0x24/0x30
[ 4417.279387]  [<ffffffff81095772>] ? insert_work+0x62/0xa0
[ 4417.280697]  [<ffffffff8116c2c7>] ? mempool_free_slab+0x17/0x20
[ 4417.282019]  [<ffffffff8116c6c9>] ? mempool_free+0x49/0x90
[ 4417.283326]  [<ffffffff812c9acf>] generic_make_request_checks+0x16f/0x360
[ 4417.284637]  [<ffffffffa0340d97>] ? thin_map+0x227/0x2c0 [dm_thin_pool]
[ 4417.285951]  [<ffffffff812c9ce7>] generic_make_request+0x27/0x130
[ 4417.287240]  [<ffffffffa0230b3d>] __map_bio+0xad/0x100 [dm_mod]
[ 4417.288503]  [<ffffffffa023257e>] __clone_and_map_data_bio+0x15e/0x240 [dm_mod]
[ 4417.289778]  [<ffffffffa02329ea>] __split_and_process_bio+0x38a/0x500 [dm_mod]
[ 4417.291062]  [<ffffffffa0232c91>] dm_make_request+0x131/0x1a0 [dm_mod]
[ 4417.292344]  [<ffffffff812c9da2>] generic_make_request+0xe2/0x130
[ 4417.293626]  [<ffffffff812c9e61>] submit_bio+0x71/0x150
[ 4417.294909]  [<ffffffff8121ab1d>] ? bio_alloc_bioset+0x20d/0x360
[ 4417.296195]  [<ffffffff81215acb>] _submit_bh+0x14b/0x220
[ 4417.297484]  [<ffffffff81215bb0>] submit_bh+0x10/0x20
[ 4417.298744]  [<ffffffffa016d8d8>] jbd2_journal_commit_transaction+0x6c8/0x19a0 [jbd2]
[ 4417.300014]  [<ffffffff810135b8>] ? __switch_to+0xf8/0x4c0
[ 4417.301268]  [<ffffffffa01731e9>] kjournald2+0xc9/0x270 [jbd2]
[ 4417.302524]  [<ffffffff810a0fd0>] ? wake_up_atomic_t+0x30/0x30
[ 4417.303753]  [<ffffffffa0173120>] ? commit_timeout+0x10/0x10 [jbd2]
[ 4417.304950]  [<ffffffff8109ffef>] kthread+0xcf/0xe0
[ 4417.306107]  [<ffffffff8109ff20>] ? kthread_create_on_node+0x140/0x140
[ 4417.307255]  [<ffffffff81647f18>] ret_from_fork+0x58/0x90
[ 4417.308349]  [<ffffffff8109ff20>] ? kthread_create_on_node+0x140/0x140
......

Now we introduce a new bio flag BIO_THROTL_STATED to make sure
blkg_get/put only get called once for the same bio.
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NXiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

Add blkio.throttle.io_service_time and blkio.throttle.io_wait_time to
get per-cgroup io delay statistics.
io_service_time represents the time spent after io throttle to io
completion, while io_wait_time represents the time spent on throttle
queue.
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Reviewed-by: NXiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

We found huge performance lost on below particular Intel's disk drive
when discard zeroout functionality is enabled on it. The issue was
found when we have ext4 filesystem mounted on the disk drive and
started regular FIO testing. With it disabled, we don't observe
performance lost any more.

81:00.0 Non-Volatile memory controller: Intel Corporation \
             PCIe Data Center SSD (rev 01)

This imposes to disable the discard zero-out functionality on above
disk drive in order to regain the high performance that NVMe disk
driver supposes to provide.

Differential Revision: https://aone.alibaba-inc.com/code/D377540Signed-off-by: NWenwei Tao <wenwei.tao@linux.alibaba.com>
Reviewed-by: NGavin Shan <shan.gavin@linux.alibaba.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NXiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

After turning off the memcg kmem charging, we still suffer
from various zombie memcg problems on production environment
because of its non-zero reference count from both page caches
and per-memcg writeback related structure(bdi_writeback takes
a reference).

After we reclaimed all the page caches of the zombie memcg,
it still can't be dropped due to its bdi_writeback.

bdi_writeback is further referenced by the inodes of files,
so the memcg can't be truely released until the inodes are
destroyed afterwards which is quite unlikely in short term.

When memcg is offlining, change it's bdi_writeback to root,
and call css_put to formally release it. We've tested on
product environment, it yields pretty good effect.

Ditto for wb_blkcg_offline().
Reviewed-by: NYang Shi <yang.shi@linux.alibaba.com>
Reviewed-by: NGavin Shan <shan.gavin@linux.alibaba.com>
Signed-off-by: NXunlei Pang <xlpang@linux.alibaba.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

Indeed tool iostat's await is not good enough, which is somewhat sketchy
and could not show request's latency on device driver's side.

Here we add a new counter to track io request's d2c time, also with this
patch, we can extend iostat to show this value easily.

Note:
I had checked how iostat is implemented, it just reads fields it needs,
so iostat won't be affected by this change, so does tsar.
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Signed-off-by: NXiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

The failover of fuse userspace daemon will reuse the existing fuse conn,
without unmounting it, during daemon crashing and recovery procedure.
But some requests might be in process in the daemon before sending out reply,
when the crash happens. This will stuck the application since it will
never get the reply after the failover.

We add the sysfs api to flush these requests, after the daemon crash, before
recovery. It is easy to reproduce the issue in the fuse userspace daemon,
just exit after receiving the request and before sending the reply back.
The application will hang up in some read/write operation, before
echo 1 > /sys/fs/fuse/connection/xxx/flush. The flush operation will make
the io fail and return the error to the application.
Signed-off-by: NMa Jie Yue <majieyue@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NXiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

When jbd2 tries to get write access to one buffer, and if this buffer
is under writeback with BH_Shadow flag, jbd2 will wait until this buffer
has been written to disk, but sometimes the time taken to wait may be
much long, especially disk capacity is almost full.

Here add a proc entry "force-copy", if its value is not zero, jbd2 will
always do meta buffer copy-cout, then we can eliminate the unnecessary
wating time here, and reduce long tail latency for buffered-write.

I construct such test case below:

$cat offline.fio
; fio-rand-RW.job for fiotest

[global]
name=fio-rand-RW
filename=fio-rand-RW
rw=randrw
rwmixread=60
rwmixwrite=40
bs=4K
direct=0
numjobs=4
time_based=1
runtime=900

[file1]
size=60G
ioengine=sync
iodepth=16

$cat online.fio
; fio-seq-write.job for fiotest

[global]
name=fio-seq-write
filename=fio-seq-write
rw=write
bs=256K
direct=0
numjobs=1
time_based=1
runtime=60

[file1]
rate=50m
size=10G
ioengine=sync
iodepth=16

With this patch:
$cat /proc/fs/jbd2/sda5-8/force_copy
0

online fio almost always get such long tail latency:

Jobs: 1 (f=1), 0B/s-0B/s: [W(1)][100.0%][w=50.0MiB/s][w=200 IOPS][eta
00m:00s]
file1: (groupid=0, jobs=1): err= 0: pid=17855: Thu Nov 15 09:45:57 2018
  write: IOPS=200, BW=50.0MiB/s (52.4MB/s)(3000MiB/60001msec)
    clat (usec): min=135, max=4086.6k, avg=867.21, stdev=50338.22
     lat (usec): min=139, max=4086.6k, avg=871.16, stdev=50338.22
    clat percentiles (usec):
     |  1.00th=[    141],  5.00th=[    143], 10.00th=[    145],
     | 20.00th=[    147], 30.00th=[    147], 40.00th=[    149],
     | 50.00th=[    149], 60.00th=[    151], 70.00th=[    153],
     | 80.00th=[    155], 90.00th=[    159], 95.00th=[    163],
     | 99.00th=[    255], 99.50th=[    273], 99.90th=[    429],
     | 99.95th=[    441], 99.99th=[3640656]

$cat /proc/fs/jbd2/sda5-8/force_copy
1

online fio latency is much better.

Jobs: 1 (f=1), 0B/s-0B/s: [W(1)][100.0%][w=50.0MiB/s][w=200 IOPS][eta
00m:00s]
file1: (groupid=0, jobs=1): err= 0: pid=8084: Thu Nov 15 09:31:15 2018
  write: IOPS=200, BW=50.0MiB/s (52.4MB/s)(3000MiB/60001msec)
    clat (usec): min=137, max=545, avg=151.35, stdev=16.22
     lat (usec): min=140, max=548, avg=155.31, stdev=16.65
    clat percentiles (usec):
     |  1.00th=[  143],  5.00th=[  145], 10.00th=[  145], 20.00th=[
147],
     | 30.00th=[  147], 40.00th=[  147], 50.00th=[  149], 60.00th=[
149],
     | 70.00th=[  151], 80.00th=[  155], 90.00th=[  157], 95.00th=[
161],
     | 99.00th=[  239], 99.50th=[  269], 99.90th=[  420], 99.95th=[
429],
     | 99.99th=[  537]

As to the cost: because we'll always need to copy meta buffer, will
consume minor cpu time and some memory(at most 32MB for 128MB journal
size).
Signed-off-by: NXiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Reviewed-by: NLiu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

In ext4_writepages(), for every iteration, mpage_prepare_extent_to_map()
will try to find 2048 pages to map and normally one bio can contain 256
pages at most. If we really found 2048 pages to map, there will be 4 bios
and 4 ext4_io_submit() calls which are called both in ext4_writepages()
and mpage_map_and_submit_extent().

But note that in mpage_map_and_submit_extent(), we hold a valid jbd2 handle,
when dioread_nolock is enabled and extent is unwritten, jbd2 commit thread
will wait this handle to finish, so wait the unwritten extent is written to
disk, this will introduce unnecessary stall time, especially longer when
the writeback operation is io throttled, need to fix this issue.

Here for this scene, we accumulate bios in ext4_io_submit's io_bio, and
only submit these bios after dropping the jbd2 handle.
Signed-off-by: NXiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Reviewed-by: NLiu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

This is a temporary workaround plan to avoid the limitation when
creating hard link cross two projids.
Signed-off-by: Nzhangliguang <zhangliguang@linux.alibaba.com>
Reviewed-by: NLiu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

/proc/fs/jbd2/${device}/info only shows whole average statistical
info about jbd2's life cycle, but it can not show jbd2 info in
specified time interval and sometimes this capability is very useful
for trouble shooting. For example, we can not see how rs_locked and
rs_flushing grows in specified time interval, but these two indexes
can explain some reasons for app's behaviours.

Here we add a new "stats" proc file like /proc/diskstats, then we can
implement a simple tool jbd2_stats which'll display detailed jbd2 info
in specified time interval. Like below(time interval 5s):

[lege@localhost ~]$ cat /proc/fs/jbd2/vdb1-8/stats
51 30 8192 0 1 241616 0 0 22 0 47158 891 942 1000 1000

[lege@localhost ~]$ gcc -o jbd2_stat jbd2_stat.c ; ./jbd2_stat

Device              tid     trans   handles    locked  flushing
logging
vdb1-8             1861       158       359     13.00      0.00
2.00

Device              tid     trans   handles    locked  flushing
logging
vdb1-8             1974       113       389     26.00      0.00
5.00

Device              tid     trans   handles    locked  flushing
logging
vdb1-8             2188       214       308     10.00      0.00
7.00

Device              tid     trans   handles    locked  flushing
logging
vdb1-8             2344       156       332     19.00      0.00
4.00
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NLiu Bo <bo.liu@linux.alibaba.com>
Signed-off-by: NXiaoguang Wang <xiaoguang.wang@linux.alibaba.com>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

This is trying to do jbd2 checkpoint in a specific kernel thread, then
checkpoint won't be under io throttle control.
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NJiufei Xue <jiufei.xue@linux.alibaba.com>
Signed-off-by: Nzhangliguang <zhangliguang@linux.alibaba.com>
Reviewed by: Baoyou Xie <baoyou.xie@linux.alibaba.com>
Reviewed-by: NLiu Bo <bo.liu@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

When backporting commit 0e4b01df8659 ("mm, memcg: throttle allocators
when failing reclaim over memory.high"), memory stall section was
inadvertently missing. Fix this issue by adding it back.

Fixes: eda29cc0 ("mm, memcg: throttle allocators when failing reclaim over memory.high")
Signed-off-by: NCaspar Zhang <caspar@linux.alibaba.com>
Acked-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

commit 3b238a64c3009fed36eaea1af629d9377759d87d upstream.

The Intel SDM states that bit 13 of Icelake's MSR_OFFCORE_RSP_x
register is valid, and used for counting hardware generated prefetches
of L3 cache. Update the bitmask to allow bit 13.

Before:
$ perf stat -e cpu/event=0xb7,umask=0x1,config1=0x1bfff/u sleep 3
 Performance counter stats for 'sleep 3':
   <not supported>      cpu/event=0xb7,umask=0x1,config1=0x1bfff/u

After:
$ perf stat -e cpu/event=0xb7,umask=0x1,config1=0x1bfff/u sleep 3
 Performance counter stats for 'sleep 3':
             9,293      cpu/event=0xb7,umask=0x1,config1=0x1bfff/u
Signed-off-by: NYunying Sun <yunying.sun@intel.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: NKan Liang <kan.liang@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: acme@kernel.org
Cc: alexander.shishkin@linux.intel.com
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: jolsa@redhat.com
Cc: namhyung@kernel.org
Link: https://lkml.kernel.org/r/20190724082932.12833-1-yunying.sun@intel.comSigned-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NLin Wang <lin.x.wang@intel.com>
Acked-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

commit faaeff98666c24376cebd0b106504d05a36881d1 upstream.

Add new model number for Icelake desktop and server to perf.

The data source encoding for Icelake server is the same as Skylake
server.
Signed-off-by: NKan Liang <kan.liang@linux.intel.com>
Signed-off-by: NPeter Zijlstra (Intel) <peterz@infradead.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: bp@alien8.de
Cc: qiuxu.zhuo@intel.com
Cc: rui.zhang@intel.com
Cc: tony.luck@intel.com
Link: https://lkml.kernel.org/r/20190603134122.13853-2-kan.liang@linux.intel.comSigned-off-by: NIngo Molnar <mingo@kernel.org>
Signed-off-by: NLin Wang <lin.x.wang@intel.com>
Acked-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

commit f26621e60b35369bca9228bc936dc723b3e421af upstream.

Add the missing kernel-doc style function parameters documentation.
Signed-off-by: NBorislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: akpm@linux-foundation.org
Cc: linux-tip-commits@vger.kernel.org
Cc: rdunlap@infradead.org
Fixes: b69c2e20f6e4 ("resource: Clean it up a bit")
Link: http://lkml.kernel.org/r/20181105093307.GA12445@zn.tnicSigned-off-by: NIngo Molnar <mingo@kernel.org>
[joseph: fix find_next_iomem_res() documentation]
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NCaspar Zhang <caspar@linux.alibaba.com>

commit f75d651587f719a813ebbbfeee570e6570731d55 upstream.

The first group of warnings is caused by a "/**" kernel-doc notation
marker but the function comments are not in kernel-doc format.
Also add another error return value here.

  ../kernel/resource.c:337: warning: Function parameter or member 'start' not described in 'find_next_iomem_res'
  ../kernel/resource.c:337: warning: Function parameter or member 'end' not described in 'find_next_iomem_res'
  ../kernel/resource.c:337: warning: Function parameter or member 'flags' not described in 'find_next_iomem_res'
  ../kernel/resource.c:337: warning: Function parameter or member 'desc' not described in 'find_next_iomem_res'
  ../kernel/resource.c:337: warning: Function parameter or member 'first_lvl' not described in 'find_next_iomem_res'
  ../kernel/resource.c:337: warning: Function parameter or member 'res' not described in 'find_next_iomem_res'

Add the missing function parameter documentation for the other warnings:

  ../kernel/resource.c:409: warning: Function parameter or member 'arg' not described in 'walk_iomem_res_desc'
  ../kernel/resource.c:409: warning: Function parameter or member 'func' not described in 'walk_iomem_res_desc'
Signed-off-by: NRandy Dunlap <rdunlap@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Borislav Petkov <bp@suse.de>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: b69c2e20f6e4 ("resource: Clean it up a bit")
Link: http://lkml.kernel.org/r/dda2e4d8-bedd-3167-20fe-8c7d2d35b354@infradead.orgSigned-off-by: NIngo Molnar <mingo@kernel.org>
[joseph: fix find_next_iomem_res() documentation]
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NCaspar Zhang <caspar@linux.alibaba.com>

commit ab3a9f2ccc080d27873f76869c9a780be45e581e upstream.

The commit 665ac7e92757 ("acpi/hmat: Register processor domain to its
memory") introduced an uninitialized "struct memory_target" that could
cause an incorrect branching.

drivers/acpi/hmat/hmat.c:385:6: warning: variable 'target' is used
uninitialized whenever 'if' condition is false
[-Wsometimes-uninitialized]
        if (p->flags & ACPI_HMAT_MEMORY_PD_VALID) {
            ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/acpi/hmat/hmat.c:392:6: note: uninitialized use occurs here
        if (target && p->flags & ACPI_HMAT_PROCESSOR_PD_VALID) {
            ^~~~~~
drivers/acpi/hmat/hmat.c:385:2: note: remove the 'if' if its condition
is always true
        if (p->flags & ACPI_HMAT_MEMORY_PD_VALID) {
        ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/acpi/hmat/hmat.c:369:30: note: initialize the variable 'target'
to silence this warning
        struct memory_target *target;
                                    ^
                                     = NULL
Signed-off-by: NQian Cai <cai@lca.pw>
Reviewed-by: NMukesh Ojha <mojha@codeaurora.org>
Fixes: 665ac7e92757 ("acpi/hmat: Register processor domain to its memory")
Reviewed-by: NNathan Chancellor <natechancellor@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Reviewed-by: NCaspar Zhang <caspar@linux.alibaba.com>

commit d6a9f7336d925364daca00557afa59a68e78b422 upstream.

I10NM_EDAC depends on CONFIG_ACPI so make that dependency explicit.
Reported-by: NBorislav Petkov <bp@suse.de>
Signed-off-by: NTony Luck <tony.luck@intel.com>
Signed-off-by: NBorislav Petkov <bp@suse.de>
Cc: Aristeu Rozanski <aris@redhat.com>
Cc: James Morse <james.morse@arm.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: https://lkml.kernel.org/r/20190205180200.26865-1-tony.luck@intel.comSigned-off-by: NCaspar Zhang <caspar@linux.alibaba.com>
Reviewed-by: NJoseph Qi <joseph.qi@linux.alibaba.com>

commit 0ceb5499a8001e5ddac2c8bd7b45eb4c643469ad upstream.

To get the changes in:

  878068ea270e ("perf/x86: Support outputting XMM registers")

That will be used in a followup patch to allow users to ask for some or
all of those registers to be collected in certain contatexts.

This silences the following perf build warning:

  Warning: Kernel ABI header at 'tools/arch/x86/include/uapi/asm/perf_regs.h' differs from latest version at 'arch/x86/include/uapi/asm/perf_regs.h'
  diff -u tools/arch/x86/include/uapi/asm/perf_regs.h arch/x86/include/uapi/asm/perf_regs.h

Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: https://lkml.kernel.org/n/tip-6pjnnrzqt3x3n2cd6br3wk7k@git.kernel.orgSigned-off-by: NArnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: NJeffle Xu <jefflexu@linux.alibaba.com>
Acked-by: NJoseph Qi <joseph.qi@linux.alibaba.com>
Acked-by: NCaspar Zhang <caspar@linux.alibaba.com>

commit 31e4ca92a7dd4cdebd7fe1456b3b0b6ace9a816f upstream

Patch series ""Hotremove" persistent memory", v6.

Recently, adding a persistent memory to be used like a regular RAM was
added to Linux.  This work extends this functionality to also allow hot
removing persistent memory.

We (Microsoft) have an important use case for this functionality.

The requirement is for physical machines with small amount of RAM (~8G)
to be able to reboot in a very short period of time (<1s).  Yet, there
is a userland state that is expensive to recreate (~2G).

The solution is to boot machines with 2G preserved for persistent
memory.

Copy the state, and hotadd the persistent memory so machine still has
all 8G available for runtime.  Before reboot, offline and hotremove
device-dax 2G, copy the memory that is needed to be preserved to pmem0
device, and reboot.

The series of operations look like this:

1. After boot restore /dev/pmem0 to ramdisk to be consumed by apps.
   and free ramdisk.
2. Convert raw pmem0 to devdax
   ndctl create-namespace --mode devdax --map mem -e namespace0.0 -f
3. Hotadd to System RAM
   echo dax0.0 > /sys/bus/dax/drivers/device_dax/unbind
   echo dax0.0 > /sys/bus/dax/drivers/kmem/new_id
   echo online_movable > /sys/devices/system/memoryXXX/state
4. Before reboot hotremove device-dax memory from System RAM
   echo offline > /sys/devices/system/memoryXXX/state
   echo dax0.0 > /sys/bus/dax/drivers/kmem/unbind
5. Create raw pmem0 device
   ndctl create-namespace --mode raw  -e namespace0.0 -f
6. Copy the state that was stored by apps to ramdisk to pmem device
7. Do kexec reboot or reboot through firmware if firmware does not
   zero memory in pmem0 region (These machines have only regular
   volatile memory). So to have pmem0 device either memmap kernel
   parameter is used, or devices nodes in dtb are specified.

This patch (of 3):

When add_memory() fails, the resource and the memory should be freed.

Link: http://lkml.kernel.org/r/20190517215438.6487-2-pasha.tatashin@soleen.com
Fixes: c221c0b0308f ("device-dax: "Hotplug" persistent memory for use like normal RAM")
Signed-off-by: NPavel Tatashin <pasha.tatashin@soleen.com>
Reviewed-by: NDave Hansen <dave.hansen@intel.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Huang Ying <ying.huang@intel.com>
Cc: James Morris <jmorris@namei.org>
Cc: Jérôme Glisse <jglisse@redhat.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Ross Zwisler <zwisler@kernel.org>
Cc: Sasha Levin <sashal@kernel.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: NYang Shi <yang.shi@linux.alibaba.com>
Reviewed-by: NGavin Shan <shan.gavin@linux.alibaba.com>

commit 40cdc60ac16a42eb4e013f84d0e7aa1d6ee060d3 upstream

device-dax based devices were missing a 'resource' attribute to indicate
the physical address range contributed by the device in question. This
information is desirable to userspace tooling that may want to use the
dax device as system-ram, and wants to selectively hotplug and online
the memory blocks associated with a given device.

Without this, the tooling would have to parse /proc/iomem for the memory
ranges contributed by dax devices, which can be a workaround, but it is
far easier to provide this information in the sysfs hierarchy.

Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NVishal Verma <vishal.l.verma@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NYang Shi <yang.shi@linux.alibaba.com>
Reviewed-by: NGavin Shan <shan.gavin@linux.alibaba.com>

commit 67476656febd7ec5f1fe1aeec3c441fcf53b1e45 upstream

This move the dependency to DEV_DAX_PMEM_COMPAT such that only
if DEV_DAX_PMEM is built as module we can allow the compat support.

This allows to test the new code easily in a emulation setup where we
often build things without module support.

Cc: <stable@vger.kernel.org>
Fixes: 730926c3b099 ("device-dax: Add /sys/class/dax backwards compatibility")
Signed-off-by: NAneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NYang Shi <yang.shi@linux.alibaba.com>
Reviewed-by: NGavin Shan <shan.gavin@linux.alibaba.com>

commit c221c0b0308fd01d9fb33a16f64d2fd95f8830a4 upstream

This is intended for use with NVDIMMs that are physically persistent
(physically like flash) so that they can be used as a cost-effective
RAM replacement.  Intel Optane DC persistent memory is one
implementation of this kind of NVDIMM.

Currently, a persistent memory region is "owned" by a device driver,
either the "Direct DAX" or "Filesystem DAX" drivers.  These drivers
allow applications to explicitly use persistent memory, generally
by being modified to use special, new libraries. (DIMM-based
persistent memory hardware/software is described in great detail
here: Documentation/nvdimm/nvdimm.txt).

However, this limits persistent memory use to applications which
*have* been modified.  To make it more broadly usable, this driver
"hotplugs" memory into the kernel, to be managed and used just like
normal RAM would be.

To make this work, management software must remove the device from
being controlled by the "Device DAX" infrastructure:

	echo dax0.0 > /sys/bus/dax/drivers/device_dax/unbind

and then tell the new driver that it can bind to the device:

	echo dax0.0 > /sys/bus/dax/drivers/kmem/new_id

After this, there will be a number of new memory sections visible
in sysfs that can be onlined, or that may get onlined by existing
udev-initiated memory hotplug rules.

This rebinding procedure is currently a one-way trip.  Once memory
is bound to "kmem", it's there permanently and can not be
unbound and assigned back to device_dax.

The kmem driver will never bind to a dax device unless the device
is *explicitly* bound to the driver.  There are two reasons for
this: One, since it is a one-way trip, it can not be undone if
bound incorrectly.  Two, the kmem driver destroys data on the
device.  Think of if you had good data on a pmem device.  It
would be catastrophic if you compile-in "kmem", but leave out
the "device_dax" driver.  kmem would take over the device and
write volatile data all over your good data.

This inherits any existing NUMA information for the newly-added
memory from the persistent memory device that came from the
firmware.  On Intel platforms, the firmware has guarantees that
require each socket's persistent memory to be in a separate
memory-only NUMA node.  That means that this patch is not expected
to create NUMA nodes, but will simply hotplug memory into existing
nodes.

Because NUMA nodes are created, the existing NUMA APIs and tools
are sufficient to create policies for applications or memory areas
to have affinity for or an aversion to using this memory.

There is currently some metadata at the beginning of pmem regions.
The section-size memory hotplug restrictions, plus this small
reserved area can cause the "loss" of a section or two of capacity.
This should be fixable in follow-on patches.  But, as a first step,
losing 256MB of memory (worst case) out of hundreds of gigabytes
is a good tradeoff vs. the required code to fix this up precisely.
This calculation is also the reason we export
memory_block_size_bytes().
Signed-off-by: NDave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: NDan Williams <dan.j.williams@intel.com>
Reviewed-by: NKeith Busch <keith.busch@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Ross Zwisler <zwisler@kernel.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Michal Hocko <mhocko@suse.com>
Cc: linux-nvdimm@lists.01.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mm@kvack.org
Cc: Huang Ying <ying.huang@intel.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Yaowei Bai <baiyaowei@cmss.chinamobile.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jerome Glisse <jglisse@redhat.com>
Reviewed-by: NVishal Verma <vishal.l.verma@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NYang Shi <yang.shi@linux.alibaba.com>
Reviewed-by: NGavin Shan <shan.gavin@linux.alibaba.com>