Modules: HDA Codec driver

Added the SSID of another HP laptop for the model 'hp' with AD1981HD.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Modules: PCM Midlevel,ALSA<-OSS emulation

Fix Oops of PCM OSS emulation occuring when multiple playback is used.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Modules: ALSA<-OSS emulation

Fix Oops due to a typo in snd_pcm_oss.c.
Signed-off-by: NOGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

These are the last conversions of pci_set_dma_mask(),
pci_set_consistent_dma_mask() and pci_dma_supported() to use DMA_xBIT_MASK
constants from linux/dma-mapping.h
Signed-off-by: NTobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix misleading help text for SND_SEQUENCER_OSS config option.
Signed-off-by: NFrederik Deweerdt <frederik.deweerdt@gmail.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds a mixer control which allows the user to switch the Aux
playback between the internal Aux jack, Wavetable, and Rear Line-In on
Aureon Universe cards.

For switching, a PCA9554 (8-line GPIO with I2C interface) and a 74HC4052
(dual 4-way mux/demux) are used.  Output 0 and 1 of the PCA9554 are
connected to the select pins of the 74HC4052. The I2C interface of the
PCA9554 is connected to the card's internal SPI bus which is also used
to control the WM8770 and CS8415. SPI and I2C on the same lines...

To communicate with the PCA9554 the WM8770 and CS8415 are disabled and
an I2C Stop Condition is generated before the Start Condition (needed
for synchronisation because other SPI traffic appear to confuse the
PCA9554). Then a normal I2C data transfer takes place.  Programming must
be done ridiculously slow; in theory, 4.7us is the minimum delay time
for normal-speed I2C according to the datasheet, but even with 10us
switching was unreliable.  The Windows driver from Terratec does the
programming very slowly, too (checked with an oscilloscope).

PCA9554 datasheet:
http://www.semiconductors.philips.com/acrobat/datasheets/PCA9554_9554A_6.pdf

74HC4052 datasheet:
http://www.semiconductors.philips.com/acrobat/datasheets/74HC_HCT4052_4.pdfSigned-off-by: NMaximilian Rehkopf <otakon@gmx.net>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

On a new board revision for pcxhr boards, the
PCXHR_CHIPSC_GPI_USERI bit is no more supported.
The cards concerned have a REV01 in their PCI ID.

As the current driver tests this bit and does not load the
first Xilinx binary when it's 1, the card will crash on Xilinx
access over PCI. (the PCI will freeze ....)

The fix (fix to version 1.0.11rc4) works for both REV00 and
REV01 cards.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

process_unsol_events() seems to assume a singlethread one (IOW, racey).
So, this patch uses create_singlethread_workqueue() instead of
create_workqueue().
Signed-off-by: NOGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

This patch adds support for high definition audio on ATI SB600.
Signed-off-by: NFelix Kuehling <fkuehlin@ati.com>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix the check of timeout in probe routines to work properly
reagrdless of HZ (ALSA bug#1976).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix the check of right channel in mixer volume put callback.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Test the volume of usb audio whether actually it works and adjusts
the resolution value according to it.

Some USB audio devices report a lower resolution than it reacts.
The only possible check is to write and read a volume value.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

- fix brown-paper-bag locking bug (lock() / return / unlock())
- improve central function snd_m3_update_ptr()
  (avoid expensive integer divisions)
- add cpu_relax() to busy-wait I/O loop as recommended
  (does this require special macro support in ALSA for older kernels??)
- constify several structs
- spelling updates
Signed-off-by: NAndreas Mohr <andi@lisas.de>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

The following patch relative to CVS from 20060324 adds the following
features to the Realtek HDA codec.

1) Define two new pin modes: ALC_PIN_DIR_IN_NOMICBIAS and
   ALC_PIN_DIR_INOUT_NOMICBIAS.  These can be used with jack mode switch
   definitions in mixers to prevent the user being offered the mic bias
   options if the hardware doesn't support it.

2) Add the ability to have different input mux definitions for different
   ADCs.  This is needed because the ALC260 chip uses different mux layouts
   for the two onboard ADCs.  A new field (num_mux_defs) was added to the
   alc_spec and alc_config_preset structures to support this.

3) Adjust numerous comments to make them consistent with the above changes.

4) Utilise the new multi-mux definition functionality for the ALC260 fujitsu
   model to allow recording of the mixer output.

5) Utilise the new multi-mux definition functionality for the ALC260 test
   model to make the mux selections a little less confusing.

6) Allow the headphone jack of the ALC260 acer model to be retasked in
   the mixer.

6) Utilise the new multi-mux definition functionality for the ALC260 acer
   model to give access to the mixer output and the retasked headphone
   jack.

At this stage the *_NOMICBIAS modes are not used.  We have reports that the
"Line" jack of at least some Acer models doesn't pass the bias out, and we
also know that NIDs 0x0f and 0x10 don't seem to accept the mic bias requests
at all.  However, I feel we need to collect more evidence on both counts
before committing to the use of *_NOMICBIAS.  In the case of the Acers, it's
not clear whether this issue (probably caused by the inclusion of DC
blocking capacitors) affects all Acer models or just a small number.  With
the issue with NIDs 0x0f and 0x10 it's unclear whether this is a hardware
bug which will be addressed in later chip revisions or if it's an
intentional restriction.  The datasheet makes no mention of the restriction
so at this stage I'm inclined to consider it a hardware bug.  Comments in
the source reflect this reasoning.

On a similar theme, the headphone jack of the Fujitsu S7020 also doesn't
appear to pass mic bias voltage.  I'm still investigating this however.

With the ability to retask the headphone jack, owners of ALC260-based Acer
laptops should now be able to record 4 channels of audio if they desire. The
multiple mux definitions allow this jack to be presented from both ADCs
(since this mux input is one of those which differs between the muxes).

This patch has been tested on a Fujitsu S7020 laptop and appears to behave
itself both for the "test" and "fujitsu" models.  Definitions using only a
single mux specification also work.  Other ALC chips should be fine but I
cannot test these myself.  The "auto" modes should also continue to function
but again I have not verified this.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Attached you'll find an ALSA driver for AdLib FM cards. An AdLib card is
just an OPL2, which was already supported by sound/drivers/opl3, so only
very minimal bus-glue is needed. The patch applies cleanly to both
2.6.16 and 2.6.16-mm1.

The driver has been tested with an actual ancient 8-bit ISA AdLib card
and works fine. It also works fine for an OPL3 {,emulation} as still
found on many ISA soundcards but given that AdLib cards don't have their
own mixer, upping the volume from 0 might be a problem without the card
driver already loaded and driving the OPL3.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

- Fix possible race of referring the setup hook from the running PCM
- Fix memory leak in an error path of proc write
- Clean up the setup hook parser
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

- Clean up initialization and destruction of substream instance
  Now snd_pcm_open_substream() alone does most initialization jobs.
  Add pcm_release callback for cleaning up at snd_pcm_release_substream()
- Tidy up PCM oss code
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

- Make snd_pcm_prepare() static
- Clean up snd_pcm_kernel_*_ioctl() functions, reduce exports
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix the wrong check of enable option in cmi8330 driver.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fixed the compilation, removing obsolete kfree_nocheck() call
for memory debugging.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fixed the compilation, removing obsolete kfree_nocheck() call
for memory debugging.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added snd-als300 driver for Avance Logic ALS300/ALS300+ soundcards
by Ash Willis.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add snd-riptide driver for Conexant Riptide chip by Peter Gruber.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fixed the noisy output wtih AD1986A 3stack model using 2 channels.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fix the re-initialization of unsolicited events at resume of stac92xx codecs.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Removed from CONFIG_EXPERIMENTAL from CONFIG_SND_CS46XX_NEW_DSP, and
make default to yes.  This option works fine for years.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added snd-miro driver for miroSOUND PCM by Martin Langer.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Removed the unused file argument of snd_power_wait().
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

I have just discovered I made an error in the register value set in 'Limit
dmx6fire to 6 dacs' patch (bug1472).  The value set should be '2a' not '0a'
as in the original patch, which unintentionally disables the 2nd MPU 401
UART.
Signed-off-by: NAlan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Added the dxs_support entry for EPoX EP-8KRAI (ALSA bug#1423).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Fixed VREF level of Mic inputs on STAC92xx codecs (ALSA bug#1953).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Add support of LG LW20 laptop with ALC880 codec (ALSA bug#1572).
Signed-off-by: NTakashi Iwai <tiwai@suse.de>

Instead of the DEV_OK macro, drivers should use pcmcia_dev_present().
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Instead of the two status values struct pcmcia_device->p_state and state,
use descriptive bitfields. Most value-checking in drivers was invalid, as
the core now only calls the ->remove() (a.k.a. detach) function in case the
attachement _and_ configuration was successful.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Most of the driver initialization isn't done in the .probe function, but in
the internal _config() functions. Make them return a value, so that .probe
can properly report whether the probing of the device succeeded or not.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

dev_link_t * and client_handle_t both mean struct pcmcai_device * by now.
Therefore, remove all such indirections.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Embed dev_link_t into struct pcmcia_device(), as they basically address the
same entity. The actual contents of dev_link_t will be cleaned up step by step.
This patch includes a bugfix from and signed-off-by Andrew Morton.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

As we do not allow setting Vcc in the pcmcia core, and Vpp1 and
Vpp2 can only be set to the same value, a lot of code can be
streamlined.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

In all but one case, the suspend and resume functions of PCMCIA drivers
contain mostly of calls to pcmcia_release_configuration() and
pcmcia_request_configuration(). Therefore, move this code out of the
drivers and into the core.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>

Convert the remaining drivers which use pcmcia_release_io or
pcmcia_release_irq, and remove the EXPORT of these symbols.
Signed-off-by: NDominik Brodowski <linux@dominikbrodowski.net>