The mvneta driver supports the Ethernet IP found in the Armada 370, XP,
380 and 385 SoCs. Since at least one more hardware feature is available
for the Armada XP SoCs then a way to identify them is needed.

This patch introduces a new compatible string "marvell,armada-xp-neta".
Signed-off-by: NSimon Guinot <simon.guinot@sequanux.org>
Fixes: c5aff182 ("net: mvneta: driver for Marvell Armada 370/XP network unit")
Cc: <stable@vger.kernel.org> # v3.8+
Acked-by: NGregory CLEMENT <gregory.clement@free-electrons.com>
Acked-by: NThomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a typo in the IPG_FRAMETOOLONGERRORS constant.
Signed-off-by: NNik Nyby <nikolas@gnu.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"reigster" -> "register"
Signed-off-by: NNik Nyby <nikolas@gnu.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes a typo in the MMC_RX_CRC_ERROR constant.
Signed-off-by: NNik Nyby <nikolas@gnu.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The vfree() function performs also input parameter validation.
Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Bump up the driver version number to reflect the changes done to
work with vmxnet3 adapter version 2
Signed-off-by: NShreyas N Bhatewara <sbhatewara@vmware.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When allocating Rx related buffers, alloc_pages is called using an order
number that is decreased until successful. A system under stress can
experience failures during this allocation process resulting in a warning
being issued. This message can be of concern to end users even though the
failure is not fatal. Since the failure is not fatal and can occur
multiple times, the driver should include the __GFP_NOWARN flag to
suppress the warning message from being issued.
Signed-off-by: NTom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All BCM7xxx integrated Gigabit PHYs have an issue in their MDIO
management controller which will make the initial read or write to them
to fail and return 0xffff. This is a real issue as the typical first
thing we do is read from MII_PHYSID1 and MII_PHYSID2 from get_phy_id()
to register a driver for these PHYs.

Coupled with the workaround in drivers/net/phy/bcm7xxx.c, this
workaround for the MDIO bus controller consists in scanning the list of
PHYs to do this initial read workaround for as part of the MDIO bus
reset routine which is invoked prior to mdiobus_scan().

Once we have a proper PHY driver/device registered, all workarounds are
located there (e.g: power management suspend/resume calls).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

All BCM7xxx integrated Gigabit PHYs have an issue in their MDIO
management controller which will make the initial read or write to them
to fail and return 0xffff. This is a real issue as the typical first
thing we do is read from MII_PHYSID1 and MII_PHYSID2 from get_phy_id()
to register a driver for these PHYs.

Coupled with the workaround in drivers/net/phy/bcm7xxx.c, this
workaround for the MDIO bus controller consists in scanning the list of
PHYs to do this initial read workaround for as part of the MDIO bus
reset routine which is invoked prior to mdiobus_scan().

Once we have a proper PHY driver/device registered, all workarounds are
located there (e.g: power management suspend/resume calls).
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The initial MDIO read or write towards the BCM7xxx integrated PHY may
fail, workaround this by inserting a dummy MII_BMSR read to force the
MDIO management controller to see at least one valid transaction and get
out of stuck state out of reset.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

With CONFIG_DMA_API_DEBUG=y bnx2x triggers the error "DMA-API: device
driver frees DMA memory with wrong function".
On archs where PAGE_SIZE > SGE_PAGE_SIZE it also triggers "DMA-API:
device driver frees DMA memory with different size".

Fix this by making the mapping and unmapping symmetric:
 - Do not map the whole pool page at once. Instead map the
   SGE_PAGE_SIZE-sized pieces individually, so they can be unmapped in
   the same manner.
 - What's mapped using dma_map_page() must be unmapped using
   dma_unmap_page().

Tested on ppc64.

Fixes: 4cace675 ("bnx2x: Alloc 4k fragment for each rx ring buffer element")
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If NO_DMA=y:

    ERROR: "dma_sync_single_for_cpu" [drivers/net/ethernet/via/via-rhine.ko] undefined!
    ERROR: "dma_set_mask" [drivers/net/ethernet/via/via-rhine.ko] undefined!
    ERROR: "dma_mapping_error" [drivers/net/ethernet/via/via-rhine.ko] undefined!
    ERROR: "dma_map_single" [drivers/net/ethernet/via/via-rhine.ko] undefined!
    ERROR: "dma_alloc_coherent" [drivers/net/ethernet/via/via-rhine.ko] undefined!
    ERROR: "dma_free_coherent" [drivers/net/ethernet/via/via-rhine.ko] undefined!
    ERROR: "dma_unmap_single" [drivers/net/ethernet/via/via-rhine.ko] undefined!
    ERROR: "dma_map_page" [drivers/net/ethernet/via/via-velocity.ko] undefined!
    ERROR: "dma_sync_single_for_cpu" [drivers/net/ethernet/via/via-velocity.ko] undefined!
    ERROR: "dma_free_coherent" [drivers/net/ethernet/via/via-velocity.ko] undefined!
    ERROR: "dma_unmap_single" [drivers/net/ethernet/via/via-velocity.ko] undefined!
    ERROR: "dma_map_single" [drivers/net/ethernet/via/via-velocity.ko] undefined!
    ERROR: "dma_alloc_coherent" [drivers/net/ethernet/via/via-velocity.ko] undefined!

Before, the symbols depended implicitly on HAS_DMA through PCI or
USE_OF.  Add explicit dependencies on HAS_DMA to fix this.

Fixes: b7d3282a ("net: via/Kconfig: replace USE_OF with OF_???")
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As some C45 10G PHYs(e.g. Cortina CS4315/CS4340 PHY) have
zero Devices In package, current driver can't get correct
devices_in_package value by non-zero Devices In package.
so let's probe more with zero Devices In package to support
more C45 PHYs.
Signed-off-by: NShengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Michel reported following lockdep splat

[   44.718117] INFO: trying to register non-static key.
[   44.723081] the code is fine but needs lockdep annotation.
[   44.728559] turning off the locking correctness validator.
[   44.734036] CPU: 8 PID: 5483 Comm: ethtool Not tainted 4.1.0
[   44.770289] Call Trace:
[   44.772741]  [<ffffffff816eb1cd>] dump_stack+0x4c/0x65
[   44.777879]  [<ffffffff8111d921>] ? console_unlock+0x1f1/0x510
[   44.783708]  [<ffffffff811121f5>] __lock_acquire+0x1d05/0x1f10
[   44.789538]  [<ffffffff8111370a>] ? mark_held_locks+0x6a/0x90
[   44.795276]  [<ffffffff81113835>] ? trace_hardirqs_on_caller+0x105/0x1d0
[   44.801967]  [<ffffffff8111390d>] ? trace_hardirqs_on+0xd/0x10
[   44.807793]  [<ffffffff811330fa>] ? hrtimer_try_to_cancel+0x4a/0x250
[   44.814142]  [<ffffffff81112ba6>] lock_acquire+0xb6/0x290
[   44.819537]  [<ffffffff810d6675>] ? flush_work+0x5/0x280
[   44.824844]  [<ffffffff810d66ad>] flush_work+0x3d/0x280
[   44.830061]  [<ffffffff810d6675>] ? flush_work+0x5/0x280
[   44.835366]  [<ffffffff816f3c43>] ? schedule_hrtimeout_range+0x13/0x20
[   44.841889]  [<ffffffff8112ec9b>] ? usleep_range+0x4b/0x50
[   44.847365]  [<ffffffff8111370a>] ? mark_held_locks+0x6a/0x90
[   44.853102]  [<ffffffff810d8585>] ? __cancel_work_timer+0x105/0x1c0
[   44.859359]  [<ffffffff81113835>] ? trace_hardirqs_on_caller+0x105/0x1d0
[   44.866045]  [<ffffffff810d851f>] __cancel_work_timer+0x9f/0x1c0
[   44.872048]  [<ffffffffa0010982>] ? bnx2x_func_stop+0x42/0x90 [bnx2x]
[   44.878481]  [<ffffffff810d8670>] cancel_work_sync+0x10/0x20
[   44.884134]  [<ffffffffa00259e5>] bnx2x_chip_cleanup+0x245/0x730 [bnx2x]
[   44.890829]  [<ffffffff8110ce02>] ? up+0x32/0x50
[   44.895439]  [<ffffffff811306b5>] ? del_timer_sync+0x5/0xd0
[   44.901005]  [<ffffffffa005596d>] bnx2x_nic_unload+0x20d/0x8e0 [bnx2x]
[   44.907527]  [<ffffffff811f1aef>] ? might_fault+0x5f/0xb0
[   44.912921]  [<ffffffffa005851c>] bnx2x_reload_if_running+0x2c/0x50 [bnx2x]
[   44.919879]  [<ffffffffa005a3c5>] bnx2x_set_ringparam+0x2b5/0x460 [bnx2x]
[   44.926664]  [<ffffffff815d498b>] dev_ethtool+0x55b/0x1c40
[   44.932148]  [<ffffffff815dfdc7>] ? rtnl_lock+0x17/0x20
[   44.937364]  [<ffffffff815e7f8b>] dev_ioctl+0x17b/0x630
[   44.942582]  [<ffffffff815abf8d>] sock_do_ioctl+0x5d/0x70
[   44.947972]  [<ffffffff815ac013>] sock_ioctl+0x73/0x280
[   44.953192]  [<ffffffff8124c1c8>] do_vfs_ioctl+0x88/0x5b0
[   44.958587]  [<ffffffff8110d0b3>] ? up_read+0x23/0x40
[   44.963631]  [<ffffffff812584cc>] ? __fget_light+0x6c/0xa0
[   44.969105]  [<ffffffff8124c781>] SyS_ioctl+0x91/0xb0
[   44.974149]  [<ffffffff816f4dd7>] system_call_fastpath+0x12/0x6f

As bnx2x_init_ptp() is only called if bp->flags contains PTP_SUPPORTED,
we also need to guard bnx2x_stop_ptp() with same condition, otherwise
ptp_task workqueue is not initialized and kernel barfs on
cancel_work_sync()

Fixes: eeed018c ("bnx2x: Add timestamping and PTP hardware clock support")
Reported-by: NMichel Lespinasse <walken@google.com>
Signed-off-by: NEric Dumazet <edumazet@google.com>
Cc: Michal Kalderon <Michal.Kalderon@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: David Decotigny <decot@google.com>
Acked-by: NSony Chacko <sony.chacko@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not all silicon implementations of the Freescale FEC hardware module
have the RACC (Receive Accelerator Function) register, so we should not
be trying to access it on those that don't. Currently none of the ColdFire
based parts with a FEC have it.

Support for RACC was introduced by commit 4c09eed9 ("net: fec: Enable imx6
enet checksum acceleration"). A fix was introduced in commit d1391930
("net: fec: Fix build for MCF5272") that disables its use on the ColdFire
M5272 part, but it doesn't fix the general case of other ColdFire parts.

To fix we create a quirk flag, FEC_QUIRK_HAS_RACC, and check it before
working with the RACC register.
Signed-off-by: NGreg Ungerer <gerg@uclinux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When limiting phy link speed using "max-speed" to 100mbps or less on a
giga bit phy, phy never completes auto negotiation and phy state
machine is held in PHY_AN. Fixing this issue by comparing the giga
bit advertise though phydev->supported doesn't have it but phy has
BMSR_ESTATEN set. So that auto negotiation is restarted as old and
new advertise are different and link comes up fine.
Signed-off-by: NMugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_ACPI=n:

    drivers/net/ethernet/apm/xgene/xgene_enet_main.c: In function ‘xgene_enet_get_resources’:
    drivers/net/ethernet/apm/xgene/xgene_enet_main.c:951: warning: ‘ret’ may be used uninitialized in this function

If the driver is bound to a legacy platform device, ret will contain
arbitrary data. If it is non-zero, it will be returned to the caller as
an error code.
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function netif_set_real_num_tx_queues() will return -EINVAL if
the second parameter < 1, so call this function with the second
parameter set to 0 is meaningless.
Signed-off-by: NLiang Li <liang.z.li@intel.com>
Reviewed-by: NDavid Vrabel <david.vrabel@citrix.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver will only configure as many queues as there are available
CPUs, up the maximum number of queues. However, it always configures
RSS as though it is using the maximum number of queues. This can cause
the device to drop a lot of RX traffic, as the packets get assigned to
nonfunctional queues.

Fix this by only configuring RSS with the number of active queues.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Down was requesting queue disables, but then exited immediately
without waiting for the queues to actually disable.  This could
allow any function called after i40evf_down to run immediately,
including i40evf_up, and causes a memory leak.

Removing the whole reinit_locked function is the best way
to go about this, and allows for the driver to handle the
state changes by requesting reset from the periodic timer.

Also, add a couple WARN_ONs in slow path to help us recognize
if we re-introduce this issue or missed any cases.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NJesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In SPT hardware does not require this driver workaround.
Removed the conditional that caused K1 workaround execution on SPT.
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to clocking changes in the Skylake platform, there was i219
data corruption. To work around this, HW team reported the need
to increase the minimum gap between the PHY FIFO read and write pointers.
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In SPT/i219, there were CRC errors in speed 10/100 full duplex.
The solution given by the HW team is to increase the IPG from 8 to 0xC
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In i219, there is a hardware bug that prevented ULP entry.
A side effect of the original software fix for this was that EEE in
Sx couldn't be enabled.
This patch implements a modified flow that allows both ULP and EEE in Sx.
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

On power up, the MAC - PHY interface needs to be set to PCIe, even if
cable is disconnected.  In ME systems, the ME handles this on exit from
Sx state. In non-ME, the driver handles it. Added a check for non-ME
system to the driver code that handles that.
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

e1000e_disable_aspm called pci_disable_link_state_locked which requires
pci_bus_sem to be held, but is also called from places where this semaphore
was not previously acquired. This patch implements two flavors of
disable_aspm, one that acquires the lock, and the other (_locked) which
should be called when the semaphore is already acquired.
Signed-off-by: NYanir Lubetkin <yanirx.lubetkin@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump version of igb to igb-5.2.18
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Disable IPv6 extension header processing as per hardware errata.

Also fix copyright date.
Signed-off-by: NTodd Fujinaka <todd.fujinaka@intel.com>
Tested-by: NAaron Brown <aaron.f.brown@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Due to FW constraints, driver must make sure that transmitted SKBs will
not be too fragmented, or in the case that they are - that each 'window'
of fragments passed to the FW would contain at least an mss worth of data.

For encapsultaed packets the calculation is wrong, since it ignores the
inner headers in the calculation of the headers' length.
This could lead to a FW assertion in case of a too-fragmented encapsulated
packet.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During an error flow when trying to access the nvram the driver doesn't
release the hw lock it acquired.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since driver statistics flow access MACs and those might reset during
link re-configurations, when we're about to change link properties we
have to make sure that statistics are not operational.
Statisics would be re-enabled [i.e., gathering of statistics would
re-commence] once physical link is achieved again.

Since driver employs a link-flap avoidance scheme, there are scenarios
where driver will receive no indication that the new link is up, and
as a result the statistics would not be re-enabled.

Preventing LFA from working in such cases would guarantee that we'll
always receive such indications and thus will fix statistics gathering.
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

20g-capable devices are not configured properly for self-test, using
10g as their speed which cause the link indication to remain down and
fail the internal loopback test.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There's a bug in today's driver where VF requests to add/remove MAC filters
always reach the Hypervisor as add requests.
This prevents the VF from changing its MAC address, as it cannot remove the
previously configured MAC and runs out of MAC credits.
Signed-off-by: NShahed Shaikh <Shahed.Shaikh@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The scratchpad is a shared block between all functions of a given device.
Due to HW limitations, we can't properly close its parity notifications
to all functions on legal flows.
E.g., it's possible that while taking a register dump from one function
a parity error would be triggered on other functions.

Today driver doesn't consider this parity as a 'real' parity unless its
being accompanied by additional indications [which would happen in a real
parity scenario]; But it does print notifications for such events in the
system logs.

This eliminates such prints - in case of real parities driver would have
additional indications; But if this is the only signal user will not even
see a parity being logged in the system.
Signed-off-by: NManish Chopra <Manish.Chopra@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Each time a flow finishes reads from the classification shadow
configuration in the driver, that flow would check for pending commands
and pass them to FW if possible.
In case there's already a completion pending command, I.e., a ramrod
that has been sent to the FW and is yet to be completed while said flow
tries to configure the pending command we would get a false error message
in logs [and panic if SOE was used for driver compilation] since the
command could not have been completed.

This prevents said print [and panic]; The pending command will be sent by
the time the completion of the current sent command would arrive.
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NAriel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ethtool shows KR supported/advertised speeds incorrectly as baseT
in cases the board is in fact KR-base.
Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This fixes several issues relating to asymmetric configuration:
 1. When user requests to disable TX, the local-device needs to
    advertise both PAUSE and ASM_DIR, but to avoid transmitting pause
    frames. In the 578xx, it would ignore the TX disable.

 2. When user advertises RX-only, ASM_DIR was advertised instead of
    PAUSE/ASM_DIR.

 3. When changing mode, the advertised PAUSE/ASM_DIR was not cleared
    before setting new one, so disabling RX or TX had no impact on the
    'advertised' as appeared in the 'ethtool -a' output.
Signed-off-by: NYaniv Rosner <Yaniv.Rosner@qlogic.com>
Signed-off-by: NYuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We use spinlock to access a single flag. We can avoid spin_locks by using
atomic variable and atomic_cmpxchg(). Use atomic_cmpxchg to set the flag
for idle to poll. And a simple atomic_set to unlock (set idle from poll).

In napi poll, if gro is enabled, we call napi_gro_receive() to deliver the
packets. Before we call napi_complete(), i.e while re-polling, if low
latency busy poll is called, we use netif_receive_skb() to deliver the packets.
At this point if there are some skb's held in GRO, busy poll could deliver the
packets out of order. So we call napi_gro_flush() to flush skbs before we
move the napi poll to idle.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vitesse VSC8641 is compatible with Vitesse 82xx
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

CONFIG_GIANFAR is not depended on FSL_SOC, it
can be built on non-PPC platforms.
Signed-off-by: NAlison Wang <alison.wang@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>