Signed-off-by: NVikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: NChad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

A previous commit changed the mfs checking to ensure the new
mfs is less or equal to the mfs supported by the FCF. This
doesn't work for BRDCM cards as they set an mfs of 2048 regardless
of whether the switch returns a larger mfs.

This patch validates the new mfs against the upper and lower spec
defined boundries for a FCoE mfs.
Signed-off-by: NVasu Dev <vasu.dev@intel.com>
Signed-off-by: NBhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: NRobert Love <robert.w.love@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This reverts commit a692b0ee.

Tom reports:

[    8.741033] ------------[ cut here ]------------
[    8.741038] WARNING: at fs/sysfs/dir.c:508 sysfs_add_one+0xc1/0xf0()
[    8.741040] Hardware name: To Be Filled By O.E.M.
[    8.741041] sysfs: cannot create duplicate filename

...and missing 2 out of 4 drives connected to mvsas.  Commit a692b0ee
made the assumption that all the phy ids an lldd registers to libsas are
unique.  However, in the "multi-chip" case mvsas does a rather annoying
duplication of phy ids in the array passed to libsas.  So, for example,
chip0 has phy0-3 at ha phy index 0-3 and chip1 has its phy0-3 at ha phy
index 4-7.  The more natural model would be to create a scsi_host (and
sas_ha) per chip (controller), but for now revert the naming fix which
unfortunately means dealing with unpredictable end-device names for a
bit longer.

Cc: Xiangliang Yu <yuxiangl@marvell.com>
Cc: Patrick Thomson <patrick.s.thomson@intel.com>
Reported-by: NTom Rini <trini@ti.com>
Tested-by: NTom Rini <trini@ti.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Normalize phy->attached_sas_addr to return a zero-address in the case
when device-type == NO_DEVICE or the linkrate is invalid to handle
expanders that put non-zero sas addresses in the discovery response:

 sas: ex 5001b4da000f903f phy02:U:0 attached: 0100000000000000 (no device)
 sas: ex 5001b4da000f903f phy01:U:0 attached: 0100000000000000 (no device)
 sas: ex 5001b4da000f903f phy03:U:0 attached: 0100000000000000 (no device)
 sas: ex 5001b4da000f903f phy00:U:0 attached: 0100000000000000 (no device)
Reported-by: NAndrzej Jakowski <andrzej.jakowski@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

This changes the ordering of initialization and probing events from:
  1/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
  2/ allocate ata_port and schedule port probe in DISCE_PROBE
...to:
  1/ allocate ata_port in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
  2/ allocate rphy in PORTE_BYTES_DMAED, DISCE_REVALIDATE_DOMAIN
  3/ schedule port probe in DISCE_PROBE

This ordering prevents PHYE_SIGNAL_LOSS_EVENTS from sneaking in to
destrory ata devices before they have been fully initialized:

  BUG: unable to handle kernel paging request at 0000000000003b10
  IP: [<ffffffffa0053d7e>] sas_ata_end_eh+0x12/0x5e [libsas]
  ...
  [<ffffffffa004d1af>] sas_unregister_common_dev+0x78/0xc9 [libsas]
  [<ffffffffa004d4d4>] sas_unregister_dev+0x4f/0xad [libsas]
  [<ffffffffa004d5b1>] sas_unregister_domain_devices+0x7f/0xbf [libsas]
  [<ffffffffa004c487>] sas_deform_port+0x61/0x1b8 [libsas]
  [<ffffffffa004bed0>] sas_phye_loss_of_signal+0x29/0x2b [libsas]

...and kills the awkward "sata domain_device briefly existing in the
domain without an ata_port" state.
Reported-by: NMichal Kosciowski <michal.kosciowski@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

The check_ready implementation in the expander-attached ata device case
polls on sas_ex_phy_discover().  The effect is that the ex_phy fields
(critically ->attached_sas_addr) can change.  When ata_eh ends and
libsas comes along to revalidate the domain
sas_unregister_devs_sas_addr() can fail to lookup devices to remove, or
fail to re-add an ata device that ata_eh marked as disabled.  So change
the code to skip the sas_address and change count updates when ata_eh is
active.

Cc: Jack Wang <jack_wang@usish.com>
Tested-by: NMaciej Patelczyk <maciej.patelczyk@intel.com>
Tested-by: NBartek Nowakowski <bartek.nowakowski@intel.com>
Tested-by: NJacek Danecki <jacek.danecki@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Since the domain_device can out live the scsi_target we need the rphy to
follow suit otherwise we run into issues like:

  BUG: unable to handle kernel NULL pointer dereference at 0000000000000050
  IP: [<ffffffffa011561b>] sas_ata_printk+0x43/0x6f [libsas]
  PGD 0
  Oops: 0000 [#1] SMP
  CPU 1
  Modules linked in: ses enclosure isci libsas scsi_transport_sas fuse sunrpc cpufreq_ondemand acpi_cpufreq freq_table mperf microcode pcspkr igb joydev iTCO_wdt ioatdma iTCO_vendor_support i2c_i801 i2c_core dca wmi hed ipv6 pata_acpi ata_generic [last unloaded: scsi_wait_scan]

  Pid: 129, comm: kworker/u:3 Not tainted 3.3.0-rc5-isci+ #1 Intel Corporation SandyBridge Platform/To be filled by O.E.M.
  RIP: 0010:[<ffffffffa011561b>] [<ffffffffa011561b>] sas_ata_printk+0x43/0x6f [libsas]
  RSP: 0018:ffff88042232dd70 EFLAGS: 00010282
  RAX: 0000000000000000 RBX: ffff8804283165b8 RCX: ffff88042232dda0
  RDX: ffff88042232dd78 RSI: ffff8804283165b8 RDI: ffffffffa01188d7
  RBP: ffff88042232ddd0 R08: ffff880388454000 R09: ffff8803edfde1f8
  R10: ffff8803edfde1f8 R11: ffff8803edfde1f8 R12: ffff880428316750
  R13: ffff880388454000 R14: ffff8803f88b31d0 R15: ffff8803f8b21d50
  FS: 0000000000000000(0000) GS:ffff88042ee20000(0000) knlGS:0000000000000000
  CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
  CR2: 0000000000000050 CR3: 0000000001a05000 CR4: 00000000000406e0
  DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
  DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
  Process kworker/u:3 (pid: 129, threadinfo ffff88042232c000, task ffff88042230c920)
  Stack:
  0000000000000000 ffff880400000018 ffff88042232dde0 ffff88042232dda0
  ffffffffa01188c4 ffff88042ee93af0 ffff88042232ddb0 ffffffff8100e047
  ffff88042232de10 ffff880420e5a2c8 ffff8803f8b21d50 ffff8803edfde1f8
  Call Trace:
  [<ffffffff8100e047>] ? load_TLS+0xb/0xf
  [<ffffffffa01156ad>] async_sas_ata_eh+0x66/0x95 [libsas]
  [<ffffffff810655e1>] async_run_entry_fn+0x9e/0x131
Reported-by: NTom Jackson <thomas.p.jackson@intel.com>
Tested-by: NTom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Commit 899fcf40 "[SCSI] libsas: set attached device type and target
protocols for local phys" setup 'phy' to be dereferenced after
list_for_each_entry(phy, &port->phy_list, port_phy_el) (i.e. phy ==
&port->phy_list) resulting in reports like:

  BUG: unable to handle kernel NULL pointer dereference at 00000000000002b0
  IP: [<ffffffffa00ce948>] sas_discover_domain+0x29e/0x4fb [libsas]

...fix by deferring sas_phy_set_target() to the end of
sas_get_port_device().
Reported-by: NTom Jackson <thomas.p.jackson@intel.com>
Tested-by: NTom Jackson <thomas.p.jackson@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

If an expander reports 'PHY VACANT' for a phy index prior to the one
that generated a BCN libsas fails rediscovery.  Since a vacant phy is
defined as a valid phy index that will never have an attached device
just continue the search.

Cc: <stable@vger.kernel.org>
Signed-off-by: NThomas Jackson <thomas.p.jackson@intel.com>
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

When requeuing work to a draining workqueue the last work instance may
not be idle, so sas_queue_work() must not touch work->entry.  Introduce
sas_work with a drain_node list_head to have a private list for
collecting work deferred due to drain collision.

Fixes reports like:
  BUG: unable to handle kernel NULL pointer dereference at           (null)
  IP: [<ffffffff810410d4>] process_one_work+0x2e/0x338
Signed-off-by: NDan Williams <dan.j.williams@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Use scsi_add_host_with_dma in ata_scsi_add_hosts to pass in the
correct DMA device(ATA host).

Bug report: http://marc.info/?l=linux-ide&m=133177818318187&w=2Reported-and-tested-by: NJörg Sommer <joerg@alea.gnuu.de>
Acked-by: NJeff Garzik <jgarzik@redhat.com>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Currently, __scsi_alloc_queue uses SCSI host's parent device
as DMA device to set segment boundary. But the parent device may not
refer to the DMA device. For example, for ATA disk, SCSI host's parent
device now refers to ATA port.

Since commit d139b9bd([SCSI] scsi_lib_dma: fix bug with dma maps on
nested scsi objects), a new field Scsi_Host->dma_dev was introduced
to refer to the real DMA device.

Use ->dma_dev in __scsi_alloc_queue to correctly set segment
boundary.

Bug report: http://marc.info/?l=linux-ide&m=133177818318187&w=2Reported-and-tested-by: NJörg Sommer <joerg@alea.gnuu.de>
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJames Bottomley <JBottomley@Parallels.com>

Pull nfsd bugfixes from J. Bruce Fields:
 "One bugfix, and one minor header fix from Jeff Layton while we're
  here"

* 'for-3.4' of git://linux-nfs.org/~bfields/linux:
  nfsd: include cld.h in the headers_install target
  nfsd: don't fail unchecked creates of non-special files

Pull drm fixes from Dave Airlie:
 "It's like a grab bag of one liners:

  - core: fix page flip error path, reorder object teardown.
  - usb: fix the drm_usb module license.
  - i915: VT switch on SNB with non-native modes fix, and a regression
    fix from 3.3.
  - radeon: missing unreserve on SI, AGP/VRAM setup fix (fixes radeon on
    IA64, but its a generic bug), an rn50 regression from 3.3, turn off
    MSIs on rv515 (it loses rearms every so often)."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  nouveau: Set special lane map for the right chipset
  drm/radeon: fix load detect on rn50 with hardcoded EDIDs.
  drm: Releasing FBs before releasing GEM objects during drm_release
  drm/nouveau/pm: don't read/write beyond end of stack buffer
  drivers: gpu: drm: gma500: mdfld_dsi_output.h: Remove not unneeded include of version.h
  radeon: fix r600/agp when vram is after AGP (v3)
  drm: fix page_flip error handling
  drm/radeon/kms: fix the regression of DVI connector check
  drm/usb: fix module license on drm/usb layer.
  drm/i915: Do not set "Enable Panel Fitter" on SNB pageflips
  drm/i915: Hold mode_config lock whilst changing mode for lastclose()
  drm/radeon/si: add missing radeon_bo_unreserve in si_rlc_init() v2
  drm/radeon: disable MSI on RV515
  drm/i915: don't clobber the special upscaling lvds timings

Pull KVM updates from Marcelo Tosatti.

* git://git.kernel.org/pub/scm/virt/kvm/kvm:
  KVM: lock slots_lock around device assignment
  KVM: VMX: Fix kvm_set_shared_msr() called in preemptible context
  KVM: unmap pages from the iommu when slots are removed
  KVM: PMU emulation: GLOBAL_CTRL MSR should be enabled on reset

The refactoring of the nv50 logic, introduced in 8663bc7c, modified the
test for the special lane map used on some Apple computers with Nvidia
chipsets. The tested MBA3,1 would still boot, but resume from suspend
stopped working. This patch restores the old test, which fixes the problem.
Signed-off-by: NHenrik Rydberg <rydberg@euromail.se>
Acked-by: NBen Skeggs <bskeggs@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

When the force changes went in back in 3.3.0, we ended up returning
disconnected in the !force case, and the connected in when forced,
as it hit the hardcoded check.

Fix it so all exits go via the hardcoded check and stop spurious
modesets on platforms with hardcoded EDIDs.

Reported-by: Evan McNabb (Red Hat)
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDave Airlie <airlied@redhat.com>

During DRM release, all the FBs and gem objects are released. If
a gem object is being used as a FB and set to a crtc, it must not
be freed before releasing the framebuffer first.

If FBs are released first, the crtc using the FB is disabled first
so now the GEM object can be freed safely. The CRTC will be enabled
again when the driver restores fbdev mode.
Signed-off-by: NPrathyush K <prathyush.k@samsung.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

NUL-terminate after strncpy.

If the parameter "profile" has length 16 or more, then strncpy
leaves "string" with no NUL terminator, so the following search
for '\n' may read beyond the end of that 16-byte buffer.
If it finds a newline there, then it will also write beyond the
end of that stack buffer.
Signed-off-by: NJim Meyering <meyering@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

The output of "make versioncheck" points a incorrect include of
version.h in the drivers/gpu/drm/gma500/mdfld_dsi_output.h:

drivers/gpu/drm/gma500/mdfld_dsi_output.h: 32 linux/version.h not needed.

If we take a look in the file, we can agree to remove it.

Cc: David Airlie <airlied@linux.ie>
Cc: <dri-devel@lists.freedesktop.org>
Signed-off-by: NMarcos Paulo de Souza <marcos.souza.org@gmail.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

If AGP is placed in the middle, the size_af is off-by-one, it results
in VRAM being placed at 0x7fffffff instead of 0x8000000.

v2: fix the vram_start setup.
v3: also fix r7xx & newer ASIC

Reported-by: russiane39 on #radeon
Signed-off-by: NJerome Glisse <jglisse@redhat.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Free event and restore event_space only when page_flip->flags has
DRM_MODE_PAGE_FLIP_EVENT if page_flip() is failed.
Signed-off-by: NJoonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: NMichel Dänzer <michel.daenzer@amd.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
  drm/i915: Do not set "Enable Panel Fitter" on SNB pageflips
  drm/i915: Hold mode_config lock whilst changing mode for lastclose()
  drm/i915: don't clobber the special upscaling lvds timings

The check of the encoder type in the commit [e00e8b5e: drm/radeon/kms:
fix analog load detection on DVI-I connectors] is obviously wrong, and
it's the culprit of the regression on my workstation with DVI-analog
connection resulting in the blank output.

Fixed the typo now.
Signed-off-by: NTakashi Iwai <tiwai@suse.de>
Reviewed-by: NAlex Deucher <alexander.deucher@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Allows this module to load correctly with certain debugging options on.

Reported on irc by scientes
Signed-off-by: NDave Airlie <airlied@redhat.com>

My 9ce70c02 "memcg: fix deadlock by inverting lrucare nesting" put a
nasty little bug into v3.3's version of mem_cgroup_replace_page_cache(),
sometimes used for FUSE.  Replacing __mem_cgroup_commit_charge_lrucare()
by __mem_cgroup_commit_charge(), I used the "pc" pointer set up earlier:
but it's for oldpage, and needs now to be for newpage.  Once oldpage was
freed, its PageCgroupUsed bit (cleared above but set again here) caused
"Bad page state" messages - and perhaps worse, being missed from newpage.
(I didn't find this by using FUSE, but in reusing the function for tmpfs.)
Signed-off-by: NHugh Dickins <hughd@google.com>
Cc: stable@vger.kernel.org [v3.3 only]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  security: fix compile error in commoncap.c

As pointed out by Jason Baron, when assigning a device to a guest
we first set the iommu domain pointer, which enables mapping
and unmapping of memory slots to the iommu.  This leaves a window
where this path is enabled, but we haven't synchronized the iommu
mappings to the existing memory slots.  Thus a slot being removed
at that point could send us down unexpected code paths removing
non-existent pinnings and iommu mappings.  Take the slots_lock
around creating the iommu domain and initial mappings as well as
around iommu teardown to avoid this race.
Signed-off-by: NAlex Williamson <alex.williamson@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Add missing "personality.h"
security/commoncap.c: In function 'cap_bprm_set_creds':
security/commoncap.c:510: error: 'PER_CLEAR_ON_SETID' undeclared (first use in this function)
security/commoncap.c:510: error: (Each undeclared identifier is reported only once
security/commoncap.c:510: error: for each function it appears in.)
Signed-off-by: NJonghwan Choi <jhbird.choi@samsung.com>
Acked-by: NSerge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: NJames Morris <james.l.morris@oracle.com>

kvm_set_shared_msr() may not be called in preemptible context,
but vmx_set_msr() does so:

  BUG: using smp_processor_id() in preemptible [00000000] code: qemu-kvm/22713
  caller is kvm_set_shared_msr+0x32/0xa0 [kvm]
  Pid: 22713, comm: qemu-kvm Not tainted 3.4.0-rc3+ #39
  Call Trace:
   [<ffffffff8131fa82>] debug_smp_processor_id+0xe2/0x100
   [<ffffffffa0328ae2>] kvm_set_shared_msr+0x32/0xa0 [kvm]
   [<ffffffffa03a103b>] vmx_set_msr+0x28b/0x2d0 [kvm_intel]
   ...

Making kvm_set_shared_msr() work in preemptible is cleaner, but
it's used in the fast path.  Making two variants is overkill, so
this patch just disables preemption around the call.
Reported-by: NDave Jones <davej@redhat.com>
Signed-off-by: NAvi Kivity <avi@redhat.com>
Signed-off-by: NMarcelo Tosatti <mtosatti@redhat.com>

Pull fuse updates from Miklos Szeredi.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
  fuse: use flexible array in fuse.h
  fuse: allow nanosecond granularity
  fuse: O_DIRECT support for files
  fuse: fix nlink after unlink

Pull s390 updates from Martin Schwidefsky:
 "A couple of bug fixes, one of them is a TLB flush fix.  Included as
  well is one small coding style patch and a patch to update the default
  configuration."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
  [S390] Fix compile error in swab.h
  [S390] Fix stfle() lowcore protection problem
  [S390] cpum_cf: get rid of compile warnings
  [S390] irq: simple coding style change
  [S390] update default configuration
  [S390] fix tlb flushing for page table pages
  [S390] kernel: Use local_irq_save() for memcpy_real()
  [S390] s390/char/vmur.c: fix memory leak
  [S390] drivers/s390/block/dasd_eckd.c: add missing dasd_sfree_request

Pull security subsystem fixes from James Morris.

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  fcaps: clear the same personality flags as suid when fcaps are used
  mpi: Avoid using freed pointer in mpi_lshift_limbs()
  Smack: move label list initialization

The BCJ filters were meant to be enabled already on these
archs, but the xz_wrap.sh script was buggy. Enabling the
filters should give smaller kernel images.

xz_wrap.sh will now use $SRCARCH instead of $ARCH to detect
the architecture. That way it doesn't need to care about the
subarchs (like i386 vs. x86_64) since the BCJ filters don't
care either.
Signed-off-by: NLasse Collin <lasse.collin@tukaani.org>
Acked-by: NJan Beulich <jbeulich@suse.com>
Acked-by: NH. Peter Anvin <hpa@zytor.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Pull libara fixes from Jeff Garzik:

 - Notable regression fix.  Forbid dynamic runtime power management by
   default, due to issues with suspend/resume and hotplug.

   To re-enable, use sysfs.

 - make ata_print_id atomic, due to ref from multiple contexts

 - sata_mv warning fix

 - ata_piix new PCI ID

* tag 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  libata: forbid port runtime pm by default, fixing regression
  libata: make ata_print_id atomic
  sata_mv: silence an uninitialized variable warning
  ata_piix: IDE-mode SATA patch for Intel DH89xxCC DeviceIDs

Forbid port runtime pm by default because it has known hotplug issue.
User can allow it by, for example

echo auto > /sys/devices/pci0000:00/0000:00:1f.2/ata2/power/control
Signed-off-by: NLin Ming <ming.m.lin@intel.com>
Signed-off-by: NJeff Garzik <jgarzik@redhat.com>

This reverts commit 6fe0d062.

Paul bisected this regression.

The conversion was done blindly and is wrong, as it does not provide a
primary handler to disable the level type irq on the device level.
Neither does it set the IRQF_ONESHOT flag which handles that at the irq
line level.  This can't be done as the interrupt might be shared, though
we might extend the core to force it.

So an interrupt on this line will wake up the thread, but immediately
unmask the irq after that.  Due to the interrupt being level type the
hardware interrupt is raised over and over and prevents the irq thread
from handling it.  Fail.

request_irq() unfortunately does not refuse such a request and the patch
was obviously never tested with real interrupts.
Bisected-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Not only do the pageflip work without it at non-native modes (i.e. with
the panel fitter enabled), it also causes normal (non-pageflipped)
modesets to fail.
Reported-by: NAdam Jackson <ajax@redhat.com>
Tested-by: NAdam Jackson <ajax@redhat.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Wanted-by-for-fixes: Dave Airlie <airlied@gmail.com>
Signed-Off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

If a process increases permissions using fcaps all of the dangerous
personality flags which are cleared for suid apps should also be cleared.
Thus programs given priviledge with fcaps will continue to have address space
randomization enabled even if the parent tried to disable it to make it
easier to attack.
Signed-off-by: NEric Paris <eparis@redhat.com>
Reviewed-by: NSerge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: NJames Morris <james.l.morris@oracle.com>

At the start of the function we assign 'a->d' to 'ap'. Then we use the
RESIZE_IF_NEEDED macro on 'a' - this may free 'a->d' and replace it
with newly allocaetd storage. In that case, we'll be operating on
freed memory further down in the function when we index into 'ap[]'.
Since we don't actually need 'ap' until after the use of the
RESIZE_IF_NEEDED macro we can just delay the assignment to it until
after we've potentially resized, thus avoiding the issue.

While I was there anyway I also changed the integer variable 'n' to be
const. It might as well be since we only assign to it once and use it
as a constant, and then the compiler will tell us if we ever assign to
it in the future.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NDmitry Kasatkin <dmitry.kasatkin@intel.com>
Signed-off-by: NJames Morris <james.l.morris@oracle.com>