Like other subsystems we should be able to define slave devices outside
of the w1 directory. To do this we move public facing interface
definitions to include/linux/w1.h and rename the internal definition
file to w1_internal.h.

As w1_family.h and w1_int.h contained almost entirely public
driver interface definitions we simply removed these files and
moved the remaining definitions into w1_internal.h.

With this we can now start to move slave devices out of w1/slaves and
into the subsystem based on the function they implement, again like
other drivers.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Reviewed-by: NSebastian Reichel <sre@kernel.org>
Acked-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The only use of assert() is in matrox_w1.c and is used to check the input
to probe() from the PCI subsystem for NULL values, these are guaranteed
to be populated and no other PCI driver makes this check, remove this.

As this was the only definition in w1_log.h, remove this also.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove filename from file, this is not done anymore as it doesn't
add anything and usually is incorrect as filename change often.

Also shorten the GPL to the more common address-less version and
remove excess white-space.
Signed-off-by: NAndrew F. Davis <afd@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds a driver for a DS2405 1-wire single-channel addressable switch.
The DS2405 can also work as a single-channel binary remote sensor.

This driver supports two attributes: "state" and "output" which are the
same attribute names as supported by existing DS2406, DS2408 and DS2413
drivers.
Signed-off-by: NMaciej S. Szmigiero <mail@maciej.szmigiero.name>
Acked-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NJiri Kosina <jkosina@suse.cz>

Switch the code documentation format style to DocBook format, enable
DocBook documentation generation, and fix some comments.
Signed-off-by: NDavid Fries <David@Fries.net>
Acked-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch offers the possibility to disables irqs during w1_write_bit()
and w1_reset_bus() operations as timing requirements are very strict for
the 1-wire bus protocol. Per default interrupts are enabled but can be
disabled via the module parameter "w1_disable_irqs".

Extend 1-wire reset pulse length from 480us to 500us as 480us is the
minimum requirement for the 1-wire reset/presence pulse.
Signed-off-by: NMarkus Franke <franm@hrz.tu-chemnitz.de>
Acked-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Interrupting w1_delay() in w1_read_bit() results in missing the low level
on the w1 line and receiving "1" instead of "0".

Add local_irq_save()/local_irq_restore() around the critical section
Signed-off-by: NJan Weitzel <j.weitzel@phytec.de>
Acked-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The first patch adds generic functionnality to w1_io for Resume Command
[A5h] lots of slaves support.  I found it useful for multi-commands/reset
workflows with the same slave on a multi-slave bus.

This DS2408 w1 slave driver is not complete for all the features of the
chip, but its sufficient if you use it as a simple IO expander.  Enjoy!

The ds1wm had Kconfig dependencies towards ARM && HAVE_CLK.  I took them
out since I was using the ds1wm on an x86_64 platform (ds1wm in a FPGA
through pcie) and found them irrelevant.

The clock freq/divisors at the top of ds1wm.c did not have the MSB set to
1.  This bit is CLK_EN which turns the whole prescaler and dividers on.
The driver never mentionned this bit either, so I just included this bit
right in the table entries.  I also took the liberty to add a couple of
entries to the table.  The spec doesn't explicitely mentions these
possibilities but the description and examination of the core shows the
prescalers & dividers can be used for more than the table explicitely
shows.  The table I enlarged still doesn't cover all possibilities, but
it's a good start.

I also made a few tweaks to a couple of the read and write algorithms
which made sense while I had my head very deep in the ds1wm documentation.
 We stressed it a lot with 10+ slaves on the bus, many ds2408, ds2431 and
ds2433 at the same time doing extensive interaction.  It proved quite
stable in our production environment.

This patch:

Add generic functionnality to w1_io for Resume Command [A5h] lots of
slaves support.
Signed-off-by: NJean-François Dagenais <dagenaisj@sonatest.com>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Szabolcs Gyurko <szabolcs.gyurko@tlt.hu>
Cc: Matt Reimer <mreimer@vpop.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This fixes a number of coding style issues I stubled over.
Acked-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Writes and returns sampled data back to userspace.
Signed-off-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

During test of the w1-gpio driver i found that in "w1.c:679
w1_slave_found()" the device id is converted to little-endian with
"cpu_to_le64()", but its not converted back to cpu format in "w1_io.c:293
w1_reset_select_slave()".

Based on a patch created by Andreas Hummel.

[akpm@linux-foundation.org: remove unneeded cast]
Reported-by: NAndreas Hummel <andi_hummel@gmx.de>
Signed-off-by: NEvgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Export the w1_read_8 function for use of drivers.  The OMAP HDQ
driver(drivers/w1/masters/omap_hdq.c) uses this function.

[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Madhusudhan Chikkature<madhu.cr@ti.com>
Acked-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

w1_reset_bus, added some comments about the timing and switched to msleep
for the later delay.  I don't have the hardware to test the sleep after
reset change.  The one wire doesn't have a timing requirement between
commands so it is fine.  I do have the USB hardware and it would be in big
trouble with 10ms interrupt transfers to find that the reset completed.
Signed-off-by: NDavid Fries <david@fries.net>
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Add a strong pullup option to the w1 system.  This supplies extra power
for parasite powered devices.  There is a w1_master_pullup sysfs entry and
enable_pullup module parameter to enable or disable the strong pullup.

The one wire bus requires at a minimum one wire and ground.  The common
wire is used for sending and receiving data as well as supplying power to
devices that are parasite powered of which temperature sensors can be one
example.  The bus must be idle and left high while a temperature
conversion is in progress, in addition the normal pullup resister on
larger networks or even higher temperatures might not supply enough power.
 The pullup resister can't provide too much pullup current, because
devices need to pull the bus down to write a value.  This enables the
strong pullup for supported hardware, which can supply more current when
requested.  Unsupported hardware will just delay with the bus high.

The hardware USB 2490 one wire bus master has a bit on some commands which
will enable the strong pullup as soon as the command finishes executing.
To use strong pullup, call the new w1_next_pullup function to register the
duration.  The next write command will call set_pullup before sending the
data, and reset the duration to zero once it returns.

Switched from simple_strtol to strict_strtol.
Signed-off-by: NDavid Fries <david@fries.net>
Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

w1_control_thread was removed which would wake up every second and process
newly registered family codes and complete some final cleanup for a
removed master.  Those routines were moved to the threads that were
previously requesting those operations.  A new function
w1_reconnect_slaves takes care of reconnecting existing slave devices when
a new family code is registered or removed.  The removal case was missing
and would cause a deadlock waiting for the family code reference count to
decrease, which will now happen.  A problem with registering a family code
was fixed.  A slave device would be unattached if it wasn't yet claimed,
then attached at the end of the list, two unclaimed slaves would cause an
infinite loop.

The struct w1_bus_master.search now takes a pointer to the struct
w1_master device to avoid searching for it, which would have caused a
lock ordering deadlock with the removal of w1_control_thread.
Signed-off-by: NDavid Fries <david@fries.net>
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This patch contains the following possible cleanups:
- the following file did't #include the header with the prototypes for
  it's global functions:
  - w1_int.c
- #if 0 the following unused global function:
  - w1_family.c: w1_family_get()
- make the following needlessly global functions static:
  - w1_family.c: __w1_family_put()
  - w1_io.c: w1_delay()
  - w1_io.c: w1_touch_bit()
  - w1_io.c: w1_read_8()
- remove the following unused EXPORT_SYMBOL's:
  - w1_family.c: w1_family_put
  - w1_family.c: w1_family_registered
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

From: Andrew Morton <akpm@osdl.org>

WARNING: "w1_read_block" [drivers/w1/slaves/w1_therm.ko] undefined!
WARNING: "w1_write_8" [drivers/w1/slaves/w1_therm.ko] undefined!
WARNING: "w1_reset_select_slave" [drivers/w1/slaves/w1_therm.ko] undefined!
WARNING: "w1_reset_bus" [drivers/w1/slaves/w1_ds2433.ko] undefined!
WARNING: "w1_write_8" [drivers/w1/slaves/w1_ds2433.ko] undefined!
WARNING: "w1_read_block" [drivers/w1/slaves/w1_ds2433.ko] undefined!
WARNING: "w1_write_block" [drivers/w1/slaves/w1_ds2433.ko] undefined!
WARNING: "w1_reset_select_slave" [drivers/w1/slaves/w1_ds2433.ko] undefined!

Cc: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There are three types of messages between w1 core and userspace:
1. Events. They are generated each time new master or slave device found
	either due to automatic or requested search.
2. Userspace commands. Includes read/write and search/alarm search comamnds.
3. Replies to userspace commands.

From: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch contains the following cleanups:
- make needlessly global code static
- declarations for global code belong into header files
- w1.c: #if 0 the unused struct w1_slave_device
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Acked-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

sending either a skip rom or a rom match.

Patch from Ben Gardner <bgardner@wabtec.com>
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adds the triplet w1 master method and changes w1_search() to use it.
Signed-off-by: NBen Gardner <bgardner@wabtec.com>
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Cleans up usage of touch_bit/w1_read_bit/w1_write_bit.
Signed-off-by: NBen Gardner <bgardner@wabtec.com>
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

 - white space changes.
 - list_for_each_entry/list_for_each_entry_safe and reverse changes.
 - small coding style changes.
 - removed redundant NULL checks.
 - use attribute group and macros instead of direct device attributes.
Patch is havily based on work from Adrian Bunk and Dmitry Torokhov,
thanks guys.
Signed-off-by: NEvgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!