The new flag PCI_DEV_FLAGS_NO_RELAXED_ORDERING has been added
to indicate that Relaxed Ordering Attributes (RO) should not
be used for Transaction Layer Packets (TLP) targeted toward
these affected Root Port, it will clear the bit4 in the PCIe
Device Control register, so the PCIe device drivers could
query PCIe configuration space to determine if it can send
TLPs to Root Port with the Relaxed Ordering Attributes set.

With this new flag  we don't need the config ARCH_WANT_RELAX_ORDER
to control the Relaxed Ordering Attributes for the ixgbe drivers
just like the commit 1a8b6d76 ("net:add one common config...") did,
so revert this commit.
Signed-off-by: NDing Tianhong <dingtianhong@huawei.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In ixgbe_clear_udp_tunnel_port(), we read the IXGBE_VXLANCTRL register
and then try to mask some bits out of the value, using the logical
instead of bitwise and operator.

Fixes: a21d0822 ("ixgbe: add support for geneve Rx offload")
Signed-off-by: NSabrina Dubroca <sd@queasysnail.net>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In cases where PHY register access is not supported, don't mislead
a caller into thinking that it is supported by returning a PHY
address. Instead, return -EOPNOTSUPP when PHY access is not
supported.
Signed-off-by: NMark Rustad <mark.d.rustad@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When a bundling message is received, the function tipc_link_input()
calls function tipc_msg_extract() to unbundle all inner messages of
the bundling message before adding them to input queue.

The function tipc_msg_extract() just clones all inner skb for all
inner messagges from the bundling skb. This means that the skb
headroom of an inner message overlaps with the data part of the
preceding message in the bundle.

If the message in question is a name addressed message, it may be
subject to a secondary destination lookup, and eventually be sent out
on one of the interfaces again. But, since what is perceived as headroom
by the device driver in reality is the last bytes of the preceding
message in the bundle, the latter will be overwritten by the MAC
addresses of the L2 header. If the preceding message has not yet been
consumed by the user, it will evenually be delivered with corrupted
contents.

This commit fixes this by uncloning all messages passing through the
function tipc_msg_lookup_dest(), hence ensuring that the headroom
is always valid when the message is passed on.
Signed-off-by: NTung Nguyen <tung.q.nguyen@dektech.com.au>
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We change the initialization of the skb transmit buffer queues
in the functions tipc_bcast_xmit() and tipc_rcast_xmit() to also
initialize their spinlocks. This is needed because we may, during
error conditions, need to call skb_queue_purge() on those queues
further down the stack.
Signed-off-by: NJon Maloy <jon.maloy@ericsson.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When gso_size reset to zero for the tail segment in skb_segment(), later
in ipv6_gso_segment(), __skb_udp_tunnel_segment() and gre_gso_segment()
we will get incorrect results (payload length, pcsum) for that segment.
inet_gso_segment() already has a check for gso_size before calculating
payload.

The issue was found with LTP vxlan & gre tests over ixgbe NIC.

Fixes: 07b26c94 ("gso: Support partial splitting at the frag_list pointer")
Signed-off-by: NAlexey Kodanev <alexey.kodanev@oracle.com>
Acked-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In commit fc922bb0 ("mlxsw: spectrum_router: Use one LPM tree for
all virtual routers") I increased the scale of supported VRFs by having
all of them share the same LPM tree.

In order to avoid look-ups for prefix lengths that don't exist, each
route removal would trigger an aggregation across all the active virtual
routers to see which prefix lengths are in use and which aren't and
structure the tree accordingly.

With the way the data structures are currently laid out, this is a very
expensive operation. When preformed repeatedly - due to the invocation
of the abort mechanism - and with enough VRFs, this can result in a hung
task.

For now, avoid this optimization until it can be properly re-added in
net-next.

Fixes: fc922bb0 ("mlxsw: spectrum_router: Use one LPM tree for all virtual routers")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NDavid Ahern <dsa@cumulusnetworks.com>
Tested-by: NDavid Ahern <dsa@cumulusnetworks.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

while processing Rx = Ry instruction the verifier does
regs[insn->dst_reg] = regs[insn->src_reg]
which often clears write mark (when Ry doesn't have it)
that was just set by check_reg_arg(Rx) prior to the assignment.
That causes mark_reg_read() to keep marking Rx in this block as
REG_LIVE_READ (since the logic incorrectly misses that it's
screened by the write) and in many of its parents (until lucky
write into the same Rx or beginning of the program).
That causes is_state_visited() logic to miss many pruning opportunities.

Furthermore mark_reg_read() logic propagates the read mark
for BPF_REG_FP as well (though it's readonly) which causes
harmless but unnecssary work during is_state_visited().
Note that do_propagate_liveness() skips FP correctly,
so do the same in mark_reg_read() as well.
It saves 0.2 seconds for the test below

program               before  after
bpf_lb-DLB_L3.o       2604    2304
bpf_lb-DLB_L4.o       11159   3723
bpf_lb-DUNKNOWN.o     1116    1110
bpf_lxc-DDROP_ALL.o   34566   28004
bpf_lxc-DUNKNOWN.o    53267   39026
bpf_netdev.o          17843   16943
bpf_overlay.o         8672    7929
time                  ~11 sec  ~4 sec

Fixes: dc503a8a ("bpf/verifier: track liveness for pruning")
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NEdward Cree <ecree@solarflare.com>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Should be "802.3ad" like everywhere else in the document.
Signed-off-by: NAxel Beckert <abe@deuxchevaux.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit 35e015e1 ("ipv6: fix net.ipv6.conf.all interface DAD handlers")
was intended to affect accept_dad flag handling in such a way that
DAD operation and mode on a given interface would be selected
according to the maximum value of conf/{all,interface}/accept_dad.

However, addrconf_dad_begin() checks for particular cases in which we
need to skip DAD, and this check was modified in the wrong way.

Namely, it was modified so that, if the accept_dad flag is 0 for the
given interface *or* for all interfaces, DAD would be skipped.

We have instead to skip DAD if accept_dad is 0 for the given interface
*and* for all interfaces.

Fixes: 35e015e1 ("ipv6: fix net.ipv6.conf.all interface DAD handlers")
Acked-by: NStefano Brivio <sbrivio@redhat.com>
Signed-off-by: NMatteo Croce <mcroce@redhat.com>
Reported-by: NErik Kline <ek@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ppp_release() tries to ensure that netdevices are unregistered before
decrementing the unit refcount and running ppp_destroy_interface().

This is all fine as long as the the device is unregistered by
ppp_release(): the unregister_netdevice() call, followed by
rtnl_unlock(), guarantee that the unregistration process completes
before rtnl_unlock() returns.

However, the device may be unregistered by other means (like
ppp_nl_dellink()). If this happens right before ppp_release() calling
rtnl_lock(), then ppp_release() has to wait for the concurrent
unregistration code to release the lock.
But rtnl_unlock() releases the lock before completing the device
unregistration process. This allows ppp_release() to proceed and
eventually call ppp_destroy_interface() before the unregistration
process completes. Calling free_netdev() on this partially unregistered
device will BUG():

 ------------[ cut here ]------------
 kernel BUG at net/core/dev.c:8141!
 invalid opcode: 0000 [#1] SMP

 CPU: 1 PID: 1557 Comm: pppd Not tainted 4.14.0-rc2+ #4
 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1.fc26 04/01/2014

 Call Trace:
  ppp_destroy_interface+0xd8/0xe0 [ppp_generic]
  ppp_disconnect_channel+0xda/0x110 [ppp_generic]
  ppp_unregister_channel+0x5e/0x110 [ppp_generic]
  pppox_unbind_sock+0x23/0x30 [pppox]
  pppoe_connect+0x130/0x440 [pppoe]
  SYSC_connect+0x98/0x110
  ? do_fcntl+0x2c0/0x5d0
  SyS_connect+0xe/0x10
  entry_SYSCALL_64_fastpath+0x1a/0xa5

 RIP: free_netdev+0x107/0x110 RSP: ffffc28a40573d88
 ---[ end trace ed294ff0cc40eeff ]---

We could set the ->needs_free_netdev flag on PPP devices and move the
ppp_destroy_interface() logic in the ->priv_destructor() callback. But
that'd be quite intrusive as we'd first need to unlink from the other
channels and units that depend on the device (the ones that used the
PPPIOCCONNECT and PPPIOCATTACH ioctls).

Instead, we can just let the netdevice hold a reference on its
ppp_file. This reference is dropped in ->priv_destructor(), at the very
end of the unregistration process, so that neither ppp_release() nor
ppp_disconnect_channel() can call ppp_destroy_interface() in the interim.
Reported-by: NBeniamino Galvani <bgalvani@redhat.com>
Fixes: 8cb775bc ("ppp: fix device unregistration upon netns deletion")
Signed-off-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The > should be >= so that we don't write one element beyond the end of
the array.

Fixes: 16e78122 ("selftests/net: Add a test to validate behavior of rx timestamps")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull power management fix from Rafael Wysocki:
 "This fixes a code ordering issue in the main suspend-to-idle loop that
  causes some "low power S0 idle" conditions to be incorrectly reported
  as unmet with suspend/resume debug messages enabled"

* tag 'pm-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM / s2idle: Invoke the ->wake() platform callback earlier

* pm-sleep:
  PM / s2idle: Invoke the ->wake() platform callback earlier

Merge tag 'for-4.14/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm

Pull device mapper fixes from Mike Snitzer:

 - a stable fix for the alignment of the event number reported at the
   end of the 'DM_LIST_DEVICES' ioctl.

 - a couple stable fixes for the DM crypt target.

 - a DM raid health status reporting fix.

* tag 'for-4.14/dm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
  dm raid: fix incorrect status output at the end of a "recover" process
  dm crypt: reject sector_size feature if device length is not aligned to it
  dm crypt: fix memory leak in crypt_ctr_cipher_old()
  dm ioctl: fix alignment of event number in the device list

There are three important fields that indicate the overall health and
status of an array: dev_health, sync_ratio, and sync_action.  They tell
us the condition of the devices in the array, and the degree to which
the array is synchronized.

This commit fixes a condition that is reported incorrectly.  When a member
of the array is being rebuilt or a new device is added, the "recover"
process is used to synchronize it with the rest of the array.  When the
process is complete, but the sync thread hasn't yet been reaped, it is
possible for the state of MD to be:
 mddev->recovery = [ MD_RECOVERY_RUNNING MD_RECOVERY_RECOVER MD_RECOVERY_DONE ]
 curr_resync_completed = <max dev size> (but not MaxSector)
 and all rdevs to be In_sync.
This causes the 'array_in_sync' output parameter that is passed to
rs_get_progress() to be computed incorrectly and reported as 'false' --
or not in-sync.  This in turn causes the dev_health status characters to
be reported as all 'a', rather than the proper 'A'.

This can cause erroneous output for several seconds at a time when tools
will want to be checking the condition due to events that are raised at
the end of a sync process.  Fix this by properly calculating the
'array_in_sync' return parameter in rs_get_progress().

Also, remove an unnecessary intermediate 'recovery_cp' variable in
rs_get_progress().
Signed-off-by: NJonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

Pull sound fixes from Takashi Iwai:
 "A collection of small fixes, mostly with stable ones:

 - X32 ABI fix for PCM; likely not so many people suffer from it, but
   still better to fix

 - Two minor kernel warning fixes on USB audio devices spotted by
   syzkaller

 - Regression fix of echoaudio due to its inconsistent dimension

 - Fix for HBR support on Intel DP audio, on some recent chips

 - USB-audio quirk for yet another Plantronics devices

 - Fix for potential double-fetch in ASIHPI FIFO queue"

* tag 'sound-4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: usx2y: Suppress kernel warning at page allocation failures
  Revert "ALSA: echoaudio: purge contradictions between dimension matrix members and total number of members"
  ALSA: usb-audio: Check out-of-bounds access by corrupted buffer descriptor
  ALSA: pcm: Fix structure definition for X32 ABI
  ALSA: usb-audio: Add sample rate quirk for Plantronics C310/C520-M
  ALSA: hda - program ICT bits to support HBR audio
  ALSA: asihpi: fix a potential double-fetch bug when copying puhm
  ALSA: compress: Remove unused variable

Pull HID subsystem fixes from Jiri Kosina:

 - buffer management size fix for i2c-hid driver, from Adrian Salido

 - tool ID regression fixes for Wacom driver from Jason Gerecke

 - a few small assorted fixes and a few device ID additions

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  Revert "HID: multitouch: Support ALPS PTP stick with pid 0x120A"
  HID: hidraw: fix power sequence when closing device
  HID: wacom: Always increment hdev refcount within wacom_get_hdev_data
  HID: wacom: generic: Clear ABS_MISC when tool leaves proximity
  HID: wacom: generic: Send MSC_SERIAL and ABS_MISC when leaving prox
  HID: i2c-hid: allocate hid buffers for real worst case
  HID: rmi: Make sure the HID device is opened on resume
  HID: multitouch: Support ALPS PTP stick with pid 0x120A
  HID: multitouch: support buttons and trackpoint on Lenovo X1 Tab Gen2
  HID: wacom: Correct coordinate system of touchring and pen twist
  HID: wacom: Properly report negative values from Intuos Pro 2 Bluetooth
  HID: multitouch: Fix system-control buttons not working
  HID: add multi-input quirk for IDC6680 touchscreen
  HID: wacom: leds: Don't try to control the EKR's read-only LEDs
  HID: wacom: bits shifted too much for 9th and 10th buttons

Pull networking fixes from David Miller:

 1) Check iwlwifi 9000 reorder buffer out-of-space condition properly,
    from Sara Sharon.

 2) Fix RCU splat in qualcomm rmnet driver, from Subash Abhinov
    Kasiviswanathan.

 3) Fix session and tunnel release races in l2tp, from Guillaume Nault
    and Sabrina Dubroca.

 4) Fix endian bug in sctp_diag_dump(), from Dan Carpenter.

 5) Several mlx5 driver fixes from the Mellanox folks (max flow counters
    cap check, invalid memory access in IPoIB support, etc.)

 6) tun_get_user() should bail if skb->len is zero, from Alexander
    Potapenko.

 7) Fix RCU lookups in inetpeer, from Eric Dumazet.

 8) Fix locking in packet_do_bund().

 9) Handle cb->start() error properly in netlink dump code, from Jason
    A. Donenfeld.

10) Handle multicast properly in UDP socket early demux code. From Paolo
    Abeni.

11) Several erspan bug fixes in ip_gre, from Xin Long.

12) Fix use-after-free in socket filter code, in order to handle the
    fact that listener lock is no longer taken during the three-way TCP
    handshake. From Eric Dumazet.

13) Fix infoleak in RTM_GETSTATS, from Nikolay Aleksandrov.

14) Fix tail call generation in x86-64 BPF JIT, from Alexei Starovoitov.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (77 commits)
  net: 8021q: skip packets if the vlan is down
  bpf: fix bpf_tail_call() x64 JIT
  net: stmmac: dwmac-rk: Add RK3128 GMAC support
  rndis_host: support Novatel Verizon USB730L
  net: rtnetlink: fix info leak in RTM_GETSTATS call
  socket, bpf: fix possible use after free
  mlxsw: spectrum_router: Track RIF of IPIP next hops
  mlxsw: spectrum_router: Move VRF refcounting
  net: hns3: Fix an error handling path in 'hclge_rss_init_hw()'
  net: mvpp2: Fix clock resource by adding an optional bus clock
  r8152: add Linksys USB3GIGV1 id
  l2tp: fix l2tp_eth module loading
  ip_gre: erspan device should keep dst
  ip_gre: set tunnel hlen properly in erspan_tunnel_init
  ip_gre: check packet length and mtu correctly in erspan_xmit
  ip_gre: get key from session_id correctly in erspan_rcv
  tipc: use only positive error codes in messages
  ppp: fix __percpu annotation
  udp: perform source validation for mcast early demux
  IPv4: early demux can return an error code
  ...

If the vlan is down, free the packet instead of proceeding with other
processing, or counting it as received.  If vlan interfaces are used
as slaves for bonding, with arp monitoring for connectivity, if the rx
counter is seen to be incrementing, then the bond device will not
observe that the interface is down.

CC: David S. Miller <davem@davemloft.net>
Signed-off-by: NVishakha Narvekar <Vishakha.Narvekar@dell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pull ARM SoC fixes from Olof Johansson:
 "Our first batch of fixes this release cycle, unfortunately a bit
  noisier than usual. Two major groups stand out:

   - Some pinctril dts/dtsi changes for stm32 due to a new driver being
     merged during the merge window, and this aligns the DT contents
     between the old format and the new. This could arguably be moved to
     the next merge window but it also seemed relatively harmless to
     include now.

   - Amlogic/meson had driver changes merged that required devicetree
     changes to avoid functional/performance regressions. I've already
     asked them to be more careful about this going forward, and making
     sure drivers are compatible with older DTs when they make these
     kind of changes. The platform is actively being upstreamed so
     there's a few things in flight, we've seen this happen before and
     sometimes it's hard to catch in time.

  Besides that there is the usual mix of minor fixes"

* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (33 commits)
  ARM: dts: stm32: use right pinctrl compatible for stm32f469
  ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
  ARM: defconfig: update Gemini defconfig
  ARM: defconfig: FRAMEBUFFER_CONSOLE can no longer be =m
  arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
  reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
  ARM: dts: da850-evm: add serial and ethernet aliases
  ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry
  ARM: dts: am33xx: Add spi alias to match SOC schematics
  ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both
  ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux
  ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1
  ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts
  arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
  arm64: dt marvell: Fix AP806 system controller size
  MAINTAINERS: add Macchiatobin maintainers entry
  ARC: reset: remove the misleading v1 suffix all over
  ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
  ARC: reset: Only build on archs that have IOMEM
  ARM: at91: Replace uses of virt_to_phys with __pa_symbol
  ...

Update my imgtec.com and personal email address to my kernel.org one in
a few places as MIPS will soon no longer be part of Imagination
Technologies, and add mappings in .mailcap so get_maintainer.pl reports
the right address.
Signed-off-by: NJames Hogan <jhogan@kernel.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Merge tag 'stm32-dt-fixes-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into fixes

STM32 fixes for v4.14:
---------------------

-Fix STMPE1600 bindings for stm32429i-eval board
-Use right compatible for stm32f469 pinctrl. It implies to use
pinctrl dedicated files for F4 SoCs.

* tag 'stm32-dt-fixes-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
  ARM: dts: stm32: use right pinctrl compatible for stm32f469
  ARM: dts: stm32: Fix STMPE1600 binding on stm32429i-eval board
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into fixes

Amlogic 64-bit DT updates for v4.14 (round 3)
- updates for new MMC driver features/fixes
- support high-speed modes

* tag 'amlogic-dt64-3' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic:
  ARM64: dts: meson-gxbb: nanopi-k2: enable sdr104 mode
  ARM64: dts: meson-gxbb: nanopi-k2: enable sdcard UHS modes
  ARM64: dts: meson-gxbb: p20x: enable sdcard UHS modes
  ARM64: dts: meson-gxl: libretech-cc: enable high speed modes
  ARM64: dts: meson-gxl: libretech-cc: add card regulator settle times
  ARM64: dts: meson-gxbb: nanopi-k2: add card regulator settle times
  ARM64: dts: meson: add mmc clk gate pins
  ARM64: dts: meson: remove cap-sd-highspeed from emmc nodes
  ARM64: dts: meson-gx: Use correct mmc clock source 0
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge misc fixes from Andrew Morton:
 "A lot of stuff, sorry about that. A week on a beach, then a bunch of
  time catching up then more time letting it bake in -next. Shan't do
  that again!"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (51 commits)
  include/linux/fs.h: fix comment about struct address_space
  checkpatch: fix ignoring cover-letter logic
  m32r: fix build failure
  lib/ratelimit.c: use deferred printk() version
  kernel/params.c: improve STANDARD_PARAM_DEF readability
  kernel/params.c: fix an overflow in param_attr_show
  kernel/params.c: fix the maximum length in param_get_string
  mm/memory_hotplug: define find_{smallest|biggest}_section_pfn as unsigned long
  mm/memory_hotplug: change pfn_to_section_nr/section_nr_to_pfn macro to inline function
  kernel/kcmp.c: drop branch leftover typo
  memremap: add scheduling point to devm_memremap_pages
  mm, page_alloc: add scheduling point to memmap_init_zone
  mm, memory_hotplug: add scheduling point to __add_pages
  lib/idr.c: fix comment for idr_replace()
  mm: memcontrol: use vmalloc fallback for large kmem memcg arrays
  kernel/sysctl.c: remove duplicate UINT_MAX check on do_proc_douintvec_conv()
  include/linux/bitfield.h: remove 32bit from FIELD_GET comment block
  lib/lz4: make arrays static const, reduces object code size
  exec: binfmt_misc: kill the onstack iname[BINPRM_BUF_SIZE] array
  exec: binfmt_misc: fix race between load_misc_binary() and kill_node()
  ...

Merge branch 'fixes-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security

Pull smack fix from James Morris:
 "It fixes a bug in xattr_getsecurity() where security_release_secctx()
  was being called instead of kfree(), which leads to a memory leak in
  the capabilities code. smack_inode_getsecurity is also fixed to behave
  correctly when called from there"

* 'fixes-v4.14-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
  lsm: fix smack_inode_removexattr and xattr_getsecurity memleak

Pull tracing fixlets from Steven Rostedt:
 "Two updates:

   - A memory fix with left over code from spliting out ftrace_ops and
     function graph tracer, where the function graph tracer could reset
     the trampoline pointer, leaving the old trampoline not to be freed
     (memory leak).

   - The update to Paul's patch that added the unnecessary READ_ONCE().
     This removes the unnecessary READ_ONCE() instead of having to
     rebase the branch to update the patch that added it"

* tag 'trace-v4.14-rc1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  rcu: Remove extraneous READ_ONCE()s from rcu_irq_{enter,exit}()
  ftrace: Fix kmemleak in unregister_ftrace_graph

If a crypt mapping uses optional sector_size feature, additional
restrictions to mapped device segment size must be applied in
constructor, otherwise the device activation will fail later.

Fixes: 8f0009a2 ("dm crypt: optionally support larger encryption sector size")
Cc: stable@vger.kernel.org # 4.12+
Signed-off-by: NMilan Broz <gmazyland@gmail.com>
Signed-off-by: NMike Snitzer <snitzer@redhat.com>

Currently, same stm32f429-pinctrl driver is used for stm32f429 and
stm32f469. As pin map is different between those 2 MCUs,
a stm32f469-pinctrl driver has been recently added.
This patch
 -allows to use stm32f469-pinctrl driver for stm32f469 boards
 -reworks stm32 devicetree files to fit with stm32f429 / stm32f469

In the same time it fixes an issue when only MACH_STM32F469 flag is
selected in menuconfig.

Fixes: d28bcd53 ("ARM: stm32: Introduce MACH_STM32F469 flag")
Reported-by: NNicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: NAlexandre Torgue <alexandre.torgue@st.com>

To declare gpio interrupt line for STMPE1600, 2 possibilities are offered:
-use gpio binding (and then the gpiolib interface inside driver)
-use interrupt binding as each gpio-controller are also interrupt controller
 on stm32f429.

In STMPE 1600 node both (gpio and interrupt) bindings are defined.
This patch fixes this issue and use only interrupt binding.

Fixes: c04b2e72 ("ARM: dts: stm32: Enable STMPE1600 gpio expander of STM32F429-EVAL board")
Signed-off-by: NAlexandre Torgue <alexandre.torgue@st.com>

security_inode_getsecurity() provides the text string value
of a security attribute. It does not provide a "secctx".
The code in xattr_getsecurity() that calls security_inode_getsecurity()
and then calls security_release_secctx() happened to work because
SElinux and Smack treat the attribute and the secctx the same way.
It fails for cap_inode_getsecurity(), because that module has no
secctx that ever needs releasing. It turns out that Smack is the
one that's doing things wrong by not allocating memory when instructed
to do so by the "alloc" parameter.

The fix is simple enough. Change the security_release_secctx() to
kfree() because it isn't a secctx being returned by
security_inode_getsecurity(). Change Smack to allocate the string when
told to do so.

Note: this also fixes memory leaks for LSMs which implement
inode_getsecurity but not release_secctx, such as capabilities.
Signed-off-by: NCasey Schaufler <casey@schaufler-ca.com>
Reported-by: NKonstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: stable@vger.kernel.org
Signed-off-by: NJames Morris <james.l.morris@oracle.com>

Merge tag 'omap-for-v4.14/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes

Fixes for omaps for v4.14-rc cycle

Few minor fixes for omaps, mostly just boot time warning fixes:

- Drop undocumented camera binding that got merged during the merge window by
  accident as I applied before Sakari's comments

- Fix soft reset warning for dra7 kexec boot for gpio1 as the optional clocks
  need to be enabled for reset

- Fix dra7 kexec boot clock rate for McASP as the rate is no longer the default
  rate after kexec

- Fix omap3 pandora MMC warning during boot

- Add am33xx SPI alias like we have on other SoCs

- Remove node for non-existing CPSW EMAC Ethernet on am43xx-epos-evm

* tag 'omap-for-v4.14/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  ARM: dts: am43xx-epos-evm: Remove extra CPSW EMAC entry
  ARM: dts: am33xx: Add spi alias to match SOC schematics
  ARM: OMAP2+: hsmmc: fix logic to call either omap_hsmmc_init or omap_hsmmc_late_init but not both
  ARM: dts: dra7: Set a default parent to mcasp3_ahclkx_mux
  ARM: OMAP2+: dra7xx: Set OPT_CLKS_IN_RESET flag for gpio1
  ARM: dts: nokia n900: drop unneeded/undocumented parts of the dts
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'v4.14-rockchip-dts64fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into fixes

Adding the operating points on rk3368 like they were did not end up well
for the boards as all of them are missing their cpu supplies, the OPPs
actually need to follow the <target min max> format as the regulator is
shared between both clusters and the one rk3368 board I have, somehow also
doesn't like the higher opps at all - all of which I only realized after
I brought my rk3368 board online again, after its bootloader broke.
So we revert that OPP addition for now.

And also two fixes for the mipi dsi controller on rk3399, which was
referencing a clock to high up in the clock-tree so that an intermediate
gate could be disabled inadvertently and also needs a clock for its area
in the general register files of the rk3399 soc.

* tag 'v4.14-rockchip-dts64fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  arm64: dts: rockchip: add the grf clk for dw-mipi-dsi on rk3399
  arm64: dts: rockchip: Correct MIPI DPHY PLL clock on rk3399
  Revert "arm64: dts: rockchip: Add basic cpu frequencies for RK3368"
Signed-off-by: NOlof Johansson <olof@lixom.net>

mvebu fixes for 4.14 (part 1)

Update MAINTAINERS for the Macchiatobin board (Armada 8K based)
Fix AP806 system controller size on Armada 7K/8K

* tag 'mvebu-fixes-4.14-1' of git://git.infradead.org/linux-mvebu:
  arm64: dt marvell: Fix AP806 system controller size
  MAINTAINERS: add Macchiatobin maintainers entry
Signed-off-by: NOlof Johansson <olof@lixom.net>

Reset controller fixes for v4.14

- Remove misleading HSDK v1 suffix, as there is no v2 planned
- Add missing DT binding documentation for HSDK reset driver
- Fix HSDK reset driver dependencies

* tag 'reset-fixes-for-4.14' of git://git.pengutronix.de/git/pza/linux:
  reset: Restrict RESET_HSDK to ARC_SOC_HSDK or COMPILE_TEST
  ARC: reset: remove the misleading v1 suffix all over
  ARC: reset: add missing DT binding documentation for HSDKv1 reset driver
  ARC: reset: Only build on archs that have IOMEM
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'davinci-fixes-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes

A fix for random ethernet mac address problem
on DA850 EVM.

* tag 'davinci-fixes-for-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
  ARM: dts: da850-evm: add serial and ethernet aliases
Signed-off-by: NOlof Johansson <olof@lixom.net>

Merge tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into fixes

Fixes for 4.14:
- three DT fixes for the newly introduced sama5d27_som1_ek board
- one treewide modification that didn't touch this new PM code: we
  synchronize now to be coherent with the other ARM platforms

* tag 'at91-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
  ARM: at91: Replace uses of virt_to_phys with __pa_symbol
  ARM: dts: at91: sama5d27_som1_ek: fix USB host vbus
  ARM: dts: at91: sama5d27_som1_ek: fix typos
  ARM: dts: at91: sama5d27_som1_ek: update pinmux/pinconf for LEDs and USB
Signed-off-by: NOlof Johansson <olof@lixom.net>

This updates the Gemini defconfig with drivers merged
for v4.13 or v4.14:
- ATA driver is merged
- DMA driver is merged
- RTC driver gets selected from default Kconfig
Signed-off-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

It is no longer possible to load this at runtime, so let's
change the few remaining users to have it built-in all
the time.

arch/arm/configs/zeus_defconfig:115:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE
arch/arm/configs/viper_defconfig:116:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE
arch/arm/configs/pxa_defconfig:474:warning: symbol value 'm' invalid for FRAMEBUFFER_CONSOLE
Reported-by: Nkernelci.org bot <bot@kernelci.org>
Fixes: 6104c370 ("fbcon: Make fbcon a built-time depency for fbdev")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Signed-off-by: NOlof Johansson <olof@lixom.net>

Before commit 9c5d760b ("mm: split gfp_mask and mapping flags into
separate fields") the private_* fields of struct adrress_space were
grouped together and using "ditto" in comments describing the last
fields was correct.

With introduction of gpf_mask between private_lock and private_list
"ditto" references the wrong description.

Fix it by using the elaborate description.

Link: http://lkml.kernel.org/r/1507009987-8746-1-git-send-email-rppt@linux.vnet.ibm.comSigned-off-by: NMike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Michal Hocko <mhocko@suse.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>