Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

This patch adds a new list where all requests which are canceled are
added to, so we don't loose them.  Then, after killing all inflight
urbs on bus reset (and disconnect) we'll walk over the list and clean
them up.

Without this we can end up with aborted requests lingering around in
case of status pipe transfer errors.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Simplifies locking, we'll protect the list with the device spin lock.
Also plugs races which can happen when two devices operate on the
global list.

While being at it rename the list head from "list" to "work", preparing
for the addition of a second list.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

256 luns is what the sam-4 address method 0 can handle and what
the qemu uas emulation supports.  So pick that for now.

[ v2: unlike the other two max_* fields max_channel isn't max+1 ]
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add new function to unlink and abort requests from the work
list, call it on bus reset and disconnect where we kill all
in-flight urbs.  Also reorder calls in disconnect to first
cancel transfers, then remove the scsi hba.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Two changes.  First we check whenever the request is linked in the work
list and if so take it out.  Second check whenever the command is
actually in flight before asking the device to cancel it via task
management, and in case it isn't just zap the data urbs and finish it.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Keep track whenever the request is linked into the work list or not.
Needed for request abort.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

uas_unlink_data_urbs uses this to make sure the the scsi command is
not released while looking at it.  This will be needed when we start
calling uas_unlink_data_urbs in the request cancel code paths.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add uas_unlink_data_urbs function to cancel in-flight data urbs.
Moves existing code into a separate function.

[ v2: also drop the locking, just call usb_unlink_urb no matter what,
      which is safe because the usb core guarantees the completion
      callback is called only once ]
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Streamline control flow so it is easier for gcc to follow which paths
can be taken and which can't.

Fixes "warning: 'cmdinfo' may be used uninitialized in this function"
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Forgot to unlock in the uas_eh_task_mgmt error paths.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Reported-by: NFengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add spinlock to protect uas data structures.

[ v2: s/GFP_NOIO/GFP_ATOMIC/, better don't sleep when holding a spinlock ]
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Properly report aborted commands.
Also don't access cmdinfo after kicking task management,
it may not be valid any more once it returns.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Allocate one tag for task management functions and
use it properly.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add task management support, wind up in abort and device reset error
handlers.  Cancel all in-flight urbs in bus reset handler.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use separate anchors for data and sense urbs, which
I think will be useful when implementing error handling.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

(1) Handle data pipe errors: When the data urb failed we
    didn't transfer anything, update scsi_cmnd accordingly.
(2) Cancel data transfers when we got back an error on the
    status pipe.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Set state bits after submitting data urbs & command urbs, so we know
what is in flight.  Clear data bits when the data urb is finished, clear
command bit when we see the status urb for the command.  Finish the scsi
command after running both status and data completion handlers for the
command.

Add a cmd status logging function for debugging purposes.  Hook it into
the error handler, so we see in the log what status a command is in
which the scsi layer wants cancel.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Stop reusing sense urbs, just allocate a fresh one each time and free it
when done.

Stop storing a sense urb pointer in the scsi request, all you can do
with it is misusing.  For example requeuing the sense urb, then f*ck it
up by picking the wrong one in case tagged requests don't finish in the
same order you've submitted them.  Also note that (not-yet supported)
task management ops don't have a scsi request in the first place.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit ceb3f91f.

IMO the real bug is assigning status urbs to scsi requests.  First there
is no such link in the non-stream case.  Also there isn't nessesarely a
scsi request in the first place, for example when submitting task
management requests.

This patch just papers over the real bug and introduces different status
urb handling in the stream/non-stream case for no good reason.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This reverts commit e4d8318a.

This patch makes uas.c call usb_unlink_urb on data urbs.  The data urbs
get freed in the completion callback.  This is illegal according to the
usb_unlink_urb documentation.

This patch also makes the code expect the data completion callback
being called before the status completion callback.  This isn't
guaranteed to be the case, even though the actual data transfer should
be finished by the time the status is received.

Background:  The ehci irq handler for example only know that there are
finished transfers, it then has go check the QHs & TDs to see which
transfers did actually finish.  It has no way to figure in which order
the transfers did complete.  The xhci driver can call the callbacks in
completion order thanks to the event queue.  This does nicely explain
why the driver is solid on a (usb2) xhci port whereas it goes crazy on
ehci in my testing.
Signed-off-by: NGerd Hoffmann <kraxel@redhat.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Just run into the following:
- new disk arrived in the system
- udev couldn't wait to get its hands on to to run ata_id /dev/sda
- this sent the cdb 0xa1 to the device.
- my UAS-gadget recevied the cdb and had no idea what to do with it. It
  decided to send a status URB back with sense set to invalid opcode.
- the host side received it status and completed the scsi command.
- the host sent another scsi with 4kib data buffer
- Now I was confused why the data transfer is only 512 bytes instead of
  4kib since the host is always allocating the complete transfer in one
  go.
- Finally the system crashed while walking through the sg list.

This patch adds three new flags in order to distinguish between DATA
URB completed and outstanding. If we receive status before data, we
cancel data and let data complete the command.
This solves the problem for IN and OUT transfers but does not work for
BIDI.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The protocol specific structures and defines which are used by UAS are
moved into a header files by this patch so it can be accessed by the UAS
gadget as well.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The UAS driver requires SG support by the HCD operating the device. This
patch stops UAS from operating on a HCD without sg support and prints a
message to let him know.

The spec says:
|For [USB2] backward compatibility, the device shall present [BOT] as
|alternate interface zero (primary) and [UAS] as alternate interface one
|(secondary). A device which does not need backward compatibility with
|[BOT] shall present [UAS] as alternate interface zero. In [USB2]
|systems, the [BOT] driver or an associated filter driver may need to
|issue a SET INTERFACE request for alternate interface one and then allow
|the [UAS] driver to load.

If the user used usb_modeswitch to switch to UAS then he can go back to
BOT or use a different HCD. In case UAS is the only interface then there
is currently no way out.
In future usb_sg_wait() should be extended to provide a non-blocking
interface so it can work with the UAS driver.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>

The status/sense URB is allocated on per-command basis. A read/write
looks the following way on a stream-less connection:

- send cmd tag X, queue status
- receive status, oh it is a read for tag X. queue status & read
- receive read
- receive status, oh I'm done for tag X. Cool call complete and free
  status urb.

This block repeats itself 1:1 for further commands and looks great so
far. Lets take a look now what happens if we do allow multiple commands:

- send cmd tag X, queue statusX (belongs to the command with the X tag)
- send cmd tag Y, queue statusY (belongs to the command with the Y tag)
- receive statusX, oh it is a read for tag X. queue statusX & a read
- receive read
- receive statusY, oh I'm done for tag X. Cool call complete and free statusY.
- receive statusX, oh it is a read for tag Y. queue statusY & before we
  queue the read the the following message can be observed:
  |sd 0:0:0:0: [sda] sense urb submission failure
  followed by a second attempt with the same result.

In order to address this problem we will use only one status URB for
each scsi host in case we don't have stream support (as suggested by
Matthew). This URB is requeued until the device removed. Nothing changes
on stream based endpoints.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>

In "usb/uas: use unique tags for all LUNs" we make sure to create unique
tags across all LUNs. This patch uses scsi_host_find_tag() to obtain the
correct command which is associated with the tag.
The following changes are required:
- don't use sdev->current_cmnd anymore
  Since we can have devices which don't support command queueing we must
  ensure that we can tell the two commands apart. Even if a device
  supports comand queuing we send the INQUIRY command "untagged" for
  LUN1 while we can send a tagged command to LUN0 at the same time.
  devinfo->cmnd is used for stashing the one "untagged" command.
- tag number is altered. If stream support is used then the tag number
  must match the stream number. Therefore we can't use tag 0 and must
  start at tag 1.
  In case we have untagged commands (at least the first command) we must
  be able to distinguish between command tag 0 (which becomes 1) and
  untagged command (which becomes curently also 1).
  The following tag numbers are used:
  0: never
  1: for untagged commands (devinfo->cmnd)
  2+: tagged commands.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>

I observed that on a device with multiple LUNs UAS was re-using the same
tag number for requests which were issued at the same time to both LUNs.
This patch uses scsi_init_shared_tag_map() to use unique tags for all
LUNs. With this patch I haven't seen the same tag number during the init
sequence anymore. Tag 1 is used for devices which do not adverise
command queueing.
This patch initilizes the queue before adding the scsi host like the
other two user in tree.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>

In the UAS status URB completion handler, we need to free the URB, no
matter what happens.  Fix a bug where we would leak the URB (and its
buffer) if we couldn't find a SCSI command that is associated with this
status phase.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>

UAS can work with either USB 3.0 devices that support bulk streams, or
USB 2.0 devices that do not support bulk streams.  When we're working
with a non-streams device, we need to be able to uniquely identify a
SCSI command with a tag in the IU.  Devices will barf and abort all
queued commands if they find a duplicate tag.

uas_queuecommand_lck() sets cmdinfo->stream to zero if the device
doesn't support streams, which is later passed into uas_alloc_cmd_urb()
as the variable stream.  This means the UAS driver was setting the tag
in all commands to zero for non-stream devices.  So the UAS driver won't
currently work with USB 2.0 devices.

Use the SCSI command tag instead of the stream ID for the command IU
tag.  We have to add one to the SCSI command tag because SCSI tags are
zero-based, but stream IDs are one-based, and the command tag must match
the stream ID that we're queueing the data IUs for.  Untagged SCSI
commands use stream ID 1.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>

If the original submission (or allocation) of the URBs for a SCSI
command fails, the UAS driver sticks the command structure in a
workqueue and schedules uas_do_work() to run.  That function removes the
entire queue before walking across it and attempting to resubmit.

Unfortunately, if the second submission fails, we will leak memory
(because an allocated URB was not submitted) and possibly leave the SCSI
command partially enqueued on some of the stream rings.  Fix this by
checking whether the second submission failed and re-queueing the
command to the UAS workqueue and scheduling it.
Signed-off-by: NSarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>

This converts the drivers in drivers/usb/* to use the
module_usb_driver() macro which makes the code smaller and a bit
simpler.

Added bonus is that it removes some unneeded kernel log messages about
drivers loading and/or unloading.

Cc: Simon Arlott <cxacru@fire.lp0.eu>
Cc: Duncan Sands <duncan.sands@free.fr>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Pete Zaitcev <zaitcev@redhat.com>
Cc: Oliver Neukum <oliver@neukum.name>
Cc: Juergen Stuber <starblue@users.sourceforge.net>
Cc: Cesar Miquel <miquel@df.uba.ar>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Lucas De Marchi <lucas.demarchi@profusion.mobi>
Cc: Michael Hund <mhund@ld-didactic.de>
Cc: Zack Parsons <k3bacon@gmail.com>
Cc: Melchior FRANZ <mfranz@aon.at>
Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: Dan Carpenter <error27@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The situation up to this point meant that module.h was pretty
much everywhere, regardless of whether you asked for it or not.
We are fixing that, so give the USB folks who want it an actual
include of it.
Signed-off-by: NPaul Gortmaker <paul.gortmaker@windriver.com>

If swap is on a UAS device, we could recurse into the driver by using
GFP_KERNEL.  Using GFP_NOIO ensures we won't.
Reported-by: NJames Bottomley <James.Bottomley@suse.de>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

While all existing UAS devices use alternate interface 1, this is not
guaranteed, and it has caused confusion with people trying to bind the
uas driver to non-uas devices.
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The spec calls this the status pipe.  While it is used to receive sense IUs,
it is also used to receive other IUs, so this can be confusing.
Reported-by: NLuben Tuikov <ltuikov@yahoo.com>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The IUs are not being fully initialised by the driver (due to the reserved
space).  Since we should be zeroing reserved fields, use kzalloc to do
it for us.
Reported-by: NLuben Tuikov <ltuikov@yahoo.com>
Signed-off-by: NMatthew Wilcox <willy@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>